Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Table of Contents
Related Manuals for Adam Equipment WBZ 3
Summary of Contents for Adam Equipment WBZ 3
- Page 1 Adam Equipment WBZ SERIES (with EC type Approval) (P.N. 9042, Rev. G, November 2009) Software rev.: 2.22 and above © Adam Equipment Company 2009...
- Page 2 © Adam Equipment Company 2009...
-
Page 3: Table Of Contents
AUTO POWER OFF.................... 13 13.4 AUTO CLEAR ..................... 14 13.5 CURRENCY SYMBOL ..................15 14.0 ERROR CODES..................... 16 15.0 REPLACEMENT PARTS AND ACCESSORIES ............ 16 16.0 SERVICE INFORMATION..................17 17.0 WARRANTY INFORMATION ................. 18 18.0 APPENDIX ....................... 19 © Adam Equipment Company 2009... - Page 4 © Adam Equipment Company 2009...
-
Page 5: Introduction
231 x 265 x 153 mm Battery Life 50 hours typical* Power 12 VDC, 800 mA Power Supply Module- supplied as standard Net Weight 3.3 kg / 7.26 lb *Battery Life is less when the backlight is used. © Adam Equipment Company 2009... -
Page 6: Installation
Keep the scales clean. Do not stack material • on the scales when they are not in use. UNPACKING Inside the box you will find- The Scale Stainless Steel Pan Power supply Module An Instruction manual © Adam Equipment Company 2009... -
Page 7: Setting Up
• At the end of the self-test it will display zero weight, if the zero condition has been achieved and the weighing unit that was in use last. A stable and zero symbol indicators are also displayed. © Adam Equipment Company 2009... -
Page 8: Keypad
NOTE: Not applicable for South Africa and Far East as this feature is disabled at the factory. 3. The Total Price window displays the price of the items on the scale. A symbol for the active currency is also shown. © Adam Equipment Company 2009... -
Page 9: Symbols And Indicators
The low battery symbol will flash during the time the battery is being charged. The scale need not be turned on, however the symbol will not be on if the scale is off. © Adam Equipment Company 2009... -
Page 10: Backlight
However you may need to press [ ] again to re-zero the Z scale if small amounts of weight are shown when the platform is empty. © Adam Equipment Company 2009... -
Page 11: Taring
[Tare] once more. Note: If the capacity of the scale is 6000g and a container weighing 2350g is used and tared, the scale can then be used to weigh the material of up to 3650g. © Adam Equipment Company 2009... -
Page 12: Weighing
• If a different unit price is required simply enter a new unit price. It may be necessary to remove the weight to return the scale to zero before a new value is allowed to be entered. © Adam Equipment Company 2009... -
Page 13: Rs-232
A metal pin or wire can be passed through the loops and sealed using a lead-wire seal. Ensure the seal is secured enough to prevent removing the cover without breaking the seal or damaging the enclosure. Alternative method © Adam Equipment Company 2009... -
Page 14: Calibration Counter
To change the setting- • Press the [0] key to scroll through the available options. • When the desired setting is displayed, press the [Tare] key to save the setting. The scale will return to weighing. © Adam Equipment Company 2009... -
Page 15: Price /Kg And /100G
“ bL ” “ oFF ” Backlight will be always off “ bL ” “ on ” Backlight will be always on • Press [Tare] to save the desired setting. The scale will return to weighing 13.3 AUTO POWER OFF © Adam Equipment Company 2009... -
Page 16: Auto Clear
• Press [Z/T] to save the desired setting. The scale will return to weighing NOTE: If the Auto Clear function is not available (disabled at the factory) the scale will double beep and continue without interruption when the [3] key is held for 4 seconds. © Adam Equipment Company 2009... -
Page 17: Currency Symbol
• Press the [0] key to scroll through the following options • Press the [Tare] key to save the desired setting. The scale will return to weighing. The selected symbol is displayed in the Unit Price and Total Price window. © Adam Equipment Company 2009... -
Page 18: Error Codes
Electronics is damaged. 15.0 REPLACEMENT PARTS AND ACCESSORIES If you need to order any spare parts and accessories, contact your supplier or Adam Equipment. A partial list of such items is as follows- • Power Supply Module • Stainless Steel Pan •... -
Page 19: Service Information
Include any recent history of the unit. For example: -Has it been working since it’s delivered -Has it been in contact with water -Damaged from a fire -Electrical Storms in the area -Dropped on the floor, etc. © Adam Equipment Company 2009... -
Page 20: Warranty Information
17.0 WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to defects in materials or workmanship. Warranty starts from the date of delivery. During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or Adam Equipment Company. - Page 22 Adam Equipment ADAM EQUIPMENT, BOND AVENUE, DENBIGH EAST INDUSTRIAL ESTATE, MILTON KEYNES, MK1 1SW, U.K. Tel: (01908) 274545 Fax: (01908) 641339 Intl Tel: -44 1908 -274545 Intl Fax: -44 1908 641339 E-Mail Address: info@Adamequipment.co.uk Declaration of Conformity Verklaring van overeenstemming Konformitätserklärung...
- Page 23 Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by Adam Equipment could void the user's authority to operate the equipment. WEEE COMPLIANCE...
- Page 24 For a complete listing of all Adam products visit our website at www.adamequipment.com © Copyright by Adam Equipment Co. Ltd. All rights reserved. No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Adam Equipment.
Need help?
Do you have a question about the WBZ 3 and is the answer not in the manual?
Questions and answers