ABL eMH1 Instruction Manual
Wallbox with charging cable
Hide thumbs
Also See for eMH1:
- Operating manual (228 pages) ,
- Manual (176 pages) ,
- Installation manual (95 pages)
Related Manuals for ABL eMH1
Summary of Contents for ABL eMH1
- Page 1 Wallbox eMH1 with charging cable Instruction Manual VERSION: EMH1-5X1/5X3-2017-01-10 ARTICLE NO.: 0301501...
-
Page 2: Contact
Contact Manufacturer ABL Sursum Bayerische Elektrozubehör GmbH & Co. KG Albert-Büttner-Straße 11 91207 Lauf / Pegnitz Germany Phone +49(0)9123 188-0 +49(0)9123 188-188 www.abl.de Email info@abl.de Support Phone +49(0)9123 188-600 Email emobility.support@abl.de... -
Page 3: Table Of Contents
Contents Contact Safety and Operating Notices Safety Notices in this Manual Safety notices on the device General safety information Operating instructions / Maintenance Introduction Product description Identifying your product variant Package contents and unpacking Available accessories Installation and power supply connection Prerequisites for the mounting site and installation Preparation and mechanical installation Electrical installation of your Wallbox... - Page 4 Error messages during operation with the vehicle Disruptions to the operation of the wallbox and solutions 18 Checking the integrated RCCB (only for model variants with RCCB) Taking the device out of operation Appendix Technical specifications Standards & guidelines Trademarks CE certification and declaration of compliance Glossary &...
-
Page 5: Safety And Operating Notices
Safety Notices in this Manual This instruction manual contains important information for the installation and safe use of the eMH1 – EVSE 5X1 and EVSE 5X3 Wallboxes it refers to. Please ensure therefore that you read and follow the safety notices provided. -
Page 6: General Safety Information
• Do not place containers with liquids on the device, as these may tip over and liquids may enter the device. Operating instructions / Maintenance Please note the following instructions for the operation and maintenance of your eMH1 Wallbox: • The device must be connected to the protective earth conductor of your electricity... - Page 7 (such as cleaning fluid or paint thinner), because they can dull the displays on the device. • The Wallbox must never be cleaned using a pressure cleaner or similar implement. • Check the permanently installed charging cable of your eMH1 Wallbox regularly for potential abrasions or damage. DANGER! Should you discover any damage to the charging cable or a supply cable, you must take the device out of operation immediately.
-
Page 8: Introduction
ABL is, with its eMH1 family of products, a leading supplier in this area. The eMH1 combines progressive and pleasing design with intuitive functionality: According to their requirements, users may select from models with a variety of features devel- oped for domestic and semi-public applications. -
Page 9: Identifying Your Product Variant
Identifying your product variant The eMH1 series comprises several model variants, which are mechanically and/or electrically adapted to different usage profiles. For identification, a product compliance plate is located at the back of the lockable housing cover shield near the hinge. Please... -
Page 10: Package Contents And Unpacking
Package contents and unpacking Your eMH1 Wallbox is delivered with a range of accessory components, which are necessary for the proper operation of the device. Therefore, please check immediately after unpacking whether the following components are included:... -
Page 11: Available Accessories
Available accessories ABL sells additional accessories for your eMH1 Wallbox. For the models of the EVSE 5X1 and 5X3 series, the following components are available: DESIGNATION MODEL NUMBER QUANTITY Mounting pole* For mounting all eMH1 Wallboxes with or without bracket... -
Page 12: Installation And Power Supply Connection
Prerequisites for the mounting site and installation Your eMH1 Wallbox is an electrical device and is therefore subject to particular prereq- uisites for indoor and outdoor installation: Although the housing of the eMH1 complies with the standards for the IP54 degree of protection, you must take into account cer- tain environmental conditions, especially outdoors. -
Page 13: Preparation And Mechanical Installation
Preparation and mechanical installation After determining the mounting site for the eMH1, you can begin with the mechanical installation. For installation you will need the following components: • Power drill or cordless drill (not included) •... - Page 14 inStallatiOn and pOwer Supply cOnnectiOn Drilling the mounting holes using the drilling template Proceed as follows to drill the holes using the drilling template: 1. Place the drilling template vertically on the chosen mounting surface: Use a spirit level if required. 2.
-
Page 15: Electrical Installation Of Your Wallbox
DANGER! Under all circumstances deactivate the miniature circuit breaker (MCB) al- located to the eMH1 in your domestic power distribution box before you begin electrical installation. Also ensure that the MCB cannot be reacti- vated during installation. Otherwise there is a danger of electric shock! - Page 16 inStallatiOn and pOwer Supply cOnnectiOn DANGER! The above color-coding is NOT internationally standardized: Should the in- dividual wires in the power supply cable be color-coded differently, please immediately contact a qualified electrical contractor! Have the power supply checked and replaced if necessary. After successful connection to the power supply by a qualified specialist or electrical contractor, please take the following steps to complete installation: 1.
-
Page 17: Taking Into Operation And Charging Procedure
WARNING! Ensure that your vehicle has internal DC fault current protection: Depend- ing on the country where you operate the eMH1, charging using the model variants without integrated DC-RCM may only be permitted with an external, upstream type B RCCB! Otherwise, all local regulations for connection to the power supply must be observed. -
Page 18: Normal Operation
taking intO OperatiOn and charging prOcedure • Ensure that the integrated or external (depending on model variant) FI residual cur- rent circuit breaker (RCCB) is switched on. • Ensure that the Wallbox has been installed according to the instructions in this man- ual: Check especially that there is free access to the Wallbox, that it is not exposed to direct sunlight or rain and that the electric vehicle can be connected without any strain or other encumbrance on the charging cable. -
Page 19: Charging Procedure
taking intO OperatiOn and charging prOcedure Charging procedure The EVSE 5X1 /5X3 is engineered for the fastest possible charge of your vehicle ac- cording to IEC 61851-1, Mode 3. The actual charging time depends on the battery fitted to your vehicle as well as on the energy currently remaining in the vehicle. For these reasons it is not possible to make a reliable prediction of the charging time: You will dis- cover its actual value in practice and derive your personal charging routine accordingly. -
Page 20: Taking Energy Consumption Readings
Taking energy consumption readings (model variants with energy meter) Various eMH1 model variants feature integrated electricity meters with digital displays that inform you about the energy consumption of the Wallbox at any time. The en- ergy meter is built into the Wallbox immediately next to the FI residual current circuit breaker. -
Page 21: Resolving Errors
Operating states The two indicator LEDs on the left above the front cover shield show the current oper- ating status of the eMH1 Wallbox. To indicate certain operating states, the LEDs may..be illuminated (continuous ON) ... flash ...be extinguished (continuous OFF). -
Page 22: Error Messages During Operation With The Vehicle
EVSE 5X1 / 5X3. Disruptions to the operation of the wallbox and solutions For safe operation, depending on model variant, the eMH1 has an integrated DC fault current detector and/or a residual current circuit breaker (RCCB), which detects re- sidual currents that may occur and disconnects the entire Wallbox from the electricity supply for your personal protection. -
Page 23: Checking The Integrated Rccb (Only For Model Variants With Rccb)
reSOlving errOrS To take suitable measures and restore operation in case of malfunction, you must first clearly identify the type of error. The following errors may occur: TYPE OF ERROR POSSIBLE CAUSE SUGGESTED SOLUTION The power supply is interrupted within the domestic electrical infrastructure: Check the upstream circuit breaker in the domes- The Wallbox does... -
Page 24: Taking The Device Out Of Operation
reSOlving errOrS PLEASE NOTE: The internal DC fault current detector (if present) conducts a self-test before each charging procedure: In case of an error, the respective error sequence will be shown (see page 18). Proceed as follows to test the RCCB: 1. - Page 25 reSOlving errOrS PLEASE NOTE: For model variants without RCCB, you must switch off the upstream MCB in your domestic power distribution box to temporarily or permanently de- activate the Wallbox. WARNING! The electrical de-installation of the EVSE 5X1 / 5X3 must always be car- ried out by a qualified electrical contractor.
-
Page 26: Appendix
appendix Appendix Technical specifications EVSE 5X1 Series MODEL VARIANT EVSE 501 EVSE 511 EVSE 531 IEC 61851-1/22 Compliance standard Rated voltage 230 V 50 Hz 32 A (MCB required Rated current 16 A (MCB required onsite) onsite) Max. output 3.6 kW 6.9 kW Charging cable Type 1, length ca. - Page 27 appendix MODEL VARIANT EVSE 551 EVSE 561 Compliance standard IEC 61851-1/22 Rated voltage 230 V 50 Hz Rated current 16 A (MCB required onsite) Max. output 3.6 kW Charging cable Type 1, length ca. 5 m external RCCB RCCB, Type A, 30 mA Circuit-protection devices required onsite Energy meter...
-
Page 28: Standards & Guidelines
272 x 220 x 106 mm (H x W x D) Dimensions Weight per unit ca. 4.9 kg ca. 3.9 kg Standards & guidelines Your eMH1-EVSE 5X1 / 5X3 Wallbox complies with the following standards and class- es of protection: General standards STANDARD DESCRIPTION 2004/108/EC... -
Page 29: Trademarks
appendix Device safety standards STANDARD DESCRIPTION Conductive charging systems for electric vehicles – Part IEC 61851-1 Ed 2.0:2010 1: General requirements Conductive charging systems for electric vehicles – Part IEC 61851-22 (69/201/CD) 22: AC Wallbox for electric vehicles Conductive charging systems for electric vehicles – Part DIN EN 61851-1: 2012-01 1: General requirements Conductive charging systems for electric vehicles –... -
Page 30: Ce Certification And Declaration Of Compliance
CE certification and declaration of compliance The eMH1-EVSE 5X1 / 5X3 Wallbox carries the CE mark. The respective compliance declarations can be obtained from ABL SURSUM Bayerische Elektrozubehör GmbH & Co. KG on request and are available at www.abl.de for download. -
Page 31: Drilling Template
Drilling template Your eMH1 Wallbox comes with a template (see reduced-size illustration) for drilling the mounting holes in a suitable substrate. Electrical installation of the eMH1 model variants described in these instructions must always be left to a qualified electrical contractor who will connect the device to the local power supply. -
Page 32: Warranty And Guarantee Provisions
Warranty and guarantee provisions ABL provides the legally prescribed guarantee period as well as a warranty of the same duration for the country in which the product was purchased. Should the product be operated in another country, the legal provisions of the country of purchase apply nev- ertheless: Under no circumstances are guarantees or the warranty transferable. -
Page 33: Disposal Advice
appendix Disposal advice The crossed out trash can symbol indicates that electrical and elec- tronic devices including accessories must be disposed of separate from household trash. The materials are recyclable as marked. By re-using, recycling or through other forms of processing obsolete devices, you make an important contribution to environmental protection. - Page 34 ABL SURSUM Albert-Büttner-Straße 11 Tel. +49 (0) 9123 188-0 info@abl.de Bayerische Elektrozubehör GmbH & Co. KG D-91207 Lauf / Pegnitz Fax +49 (0) 9123 188-188 www.abl.de...
Need help?
Do you have a question about the eMH1 and is the answer not in the manual?
Questions and answers