Dräger drager X-dock 5300 Instructions For Use Manual page 17

The following gas measuring devices can be used with the
X-dock and its modules:
X-dock 5300/6300/6600
with Pac module:
Dräger Pac 3500
Dräger Pac 5500
Dräger Pac 7000
2.4 GPL (General Public Licence)
Some of the device software includes open-source software,
which has been published under GPL, LGPL or another open-
source licence. They include GPL GPLv2, LGPL, MIT,
PostgreSQL, Apache, Apache 2, zlib. The source texts of the
software can be obtained from Dräger on a CD under material
number 83 21 874 for at least three years after purchase of the
software. The licence terms and conditions of the software are
included on CD.
3 Installation
NOTICE
i i
Ensure adequate space for the entire assembly.
The master and all modules must have the same
firmware version. If this is not the case, a firmware
update needs to be carried out (see chapter 6.2 on
page 23).
1. If applicable, install modules on the master station in
accordance with the assembly instructions (X-dock 6300/
6600 only).
A maximum of 10 modules can be installed on one

master station.
The available modules can be combined in any way

desired.
2. If applicable, install wall mount or cylinder holder in
accordance with the assembly instructions.
3. Remove the sleeves from the intended gas inlets and from
the gas outlet.
NOTICE
i
i
If the sleeve is not removed from the gas outlet, the
station will be unable to conduct the self-test without
errors.
4. Fit the gas feed hoses to the gas inlets on the master and
connect them to the regulator valve on the test gas
cylinder.
NOTICE
i i
Dräger recommends not exceeding a hose length of
10 m for the gas feed hoses.
5. If required, connect an exhaust hose (max. 10 m long) to
the exhaust outlet.
6. Ensure a supply of compressed air or fresh air:
Dräger X-dock 5300/6300/6600
with X-am 125 (+) module:
Dräger X-am 1700
Dräger X-am 2000
Dräger X-am 2500
Dräger X-am 5000
Dräger X-am 5600
Connect the compressed air hose to the compressed

air port (outlet pressure of pressure regulator valve
0.5 bar, flow rate >3 l/min).
OR
If required, connect the fresh air hose to the fresh air

filter.
7. Connect the power pack.
Station with up to 3 modules: Power pack 24 V / 1.33 A

Station with 4 to 10 modules: Power pack 24 V / 6.25 A

The entire system is supplied with power via the master.
NOTICE
i i
Dräger recommends the use of Dräger gas cylinders
and Dräger pressure regulator valves (see order list).
Alternatively there is the option of using a suitable
pressure regulator valve with 0.5 bar outlet pressure
and >3 l/min flow rate.
Dräger recommends connecting an exhaust hose
(max. 10 m long) to the exhaust outlet to discharge the
test gas into the open air.
4 Basics
4.1 Switching the station on or off
NOTICE
i i
If no action has occurred for 10 minutes, the station
switches automatically to standby mode.
To switch the station on:
Press and hold the

1 second.
The following information is displayed during the switch-on
process:
Software version number

To switch the station off:
Press and hold the

3 seconds.
The station switches off.
Standby mode:
Standby mode is activated after approx. 10 minutes with no

activity on the station (input via touchscreen or opening/
closing of a module cover).
When the station switches over to standby mode, any user

logged in will be logged off automatically. The user will need
to log back in again when switching back to operating mode.
The touchscreen is switched off in standby mode.

The charging function of X-am 125+ modules with charging

function is not affected by standby mode. The charging
process is not interrupted.
To switch to operating mode:

Tap the function key or

touch the touchscreen or

open or close a module flap.

Installation
key on the master for approx.
key on the master for approx.
17