Page 1 2 0 1 7 O W N E R ’ S M A N U A L...
Page 2 This manual illustrates and describes the operation of VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..6 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL Congratulations on selecting your new FCA US LLC ve- Consult the Table of Contents to determine which section hicle. Be assured that it represents precision workmanship, contains the information you desire. distinctive styling, and high quality. Since the specification of your vehicle depends on the items This Owner’s Manual has been prepared with the assis- of equipment ordered, certain descriptions and illustra-...
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER This Owner’s Manual contains WARNINGS against oper- The Vehicle Identification Number (VIN) is on the left front ating procedures that could result in a collision, bodily corner of the instrument panel and is visible from outside injury and/or death.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Tamper Alert ......18 A WORD ABOUT YOUR KEYS ....11 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Important Safety Precautions ....37 DOOR LOCKS ......25 ▫...
Page 13: A Word About Your Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS NOTE: In case the ignition does not change with the push of a button, the key fob may have a low or dead battery. In Your vehicle uses a keyless ignition system. This system this situation, a back up method can be used to operate the consists of a Remote Keyless Entry (RKE) key fob and a ignition switch.
Page 14: Key Fob
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The key fob also contains the Remote Keyless Entry (RKE) key fob and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead.
Page 15: Ignition Or Accessory On Message
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: With the Uconnect system, the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to ten minutes after the ignition is placed in the OFF position. Opening either front door will cancel this feature.
Page 16: General Information
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information WARNING! (Continued) The following regulatory statement applies to all Radio • Allowing children to be in a vehicle unattended is Frequency (RF) devices equipped in this vehicle: dangerous for a number of reasons. A child or others could be seriously or fatally injured.
Page 17: Replacement Key Fobs
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 vehicle can be used to start and operate the vehicle. The CAUTION! system will not allow the engine to crank if an invalid key • Do not make modifications or alterations to the fob is used to start and operate the vehicle.
Page 18: Customer Key Fob Programming
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This device complies with Part 15 of the FCC Rules and CAUTION! with Industry Canada license-exempt RSS standard(s). • Always remove the key fobs from the vehicle and Operation is subject to the following two conditions: lock all doors when leaving the vehicle unattended.
Page 19: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 after three minutes, turn all of the visual signals off after 15 To Disarm The System minutes, and then the vehicle security alarm will rearm The vehicle security alarm can be disarmed using any of itself.
Page 20: Tamper Alert
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the vehicle security alarm will arm regardless of whether you are in the vehicle or not.
Page 21: Remote Keyless Entry
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: • The front courtesy overhead console and door courtesy lights will turn on if the dimmer control is in the Dome ON position (extreme top position). • The Illuminated Entry system will not operate if the dimmer control is in the “Dome defeat”...
Page 22: To Lock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1st Press Of Key Fob Unlocks To Lock The Doors This feature lets you program the system to unlock either Push and release the lock button on the key fob to lock all the driver’s door or all doors on the first push of the unlock doors.
Page 23: Using The Panic Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Using The Panic Alarm Programming Additional Key Fobs To turn the Panic Alarm feature on or off, push and hold Programming key fobs may be performed at an authorized the Panic button on the key fob for at least one second and dealer.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Emergency Key Release Separating Key Fob Case 3. Remove the battery by turning the back cover over 1 — Emergency Key Release Button (battery facing downward) and tapping it lightly on a 2 —...
Page 25: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 General Information NOTE: • The vehicle must be equipped with an automatic trans- The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: mission to be equipped with Remote Start. •...
Page 26 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Vehicle security alarm not active • Remote Start Disabled — Start To Reset • Ignition in OFF position • Remote Start Aborted — Too Cold • Remote Start Aborted — Time Expired WARNING! The instrument cluster message stays active until the •...
Page 27: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • The engine can be started two consecutive times (two General Information 15-minute cycles) with the key fob. However, the igni- The following regulatory statement applies to all Radio tion must be cycled to the RUN position before you can Frequency (RF) devices equipped in this vehicle: repeat the start sequence for a third cycle.
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • Before exiting a vehicle, always shift the automatic transmission into PARK or the manual transmission into FIRST gear or REVERSE, apply the parking brake, turn the vehicle OFF, remove the key fobs...
Page 29: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! (Continued) • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter- N-Go in the ACC or ON/RUN mode.
Page 30: Child-Protection Door Lock System - Rear Doors
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks — If Equipped Automatic Unlock Doors On Exit Programming The auto door lock feature default condition is enabled. To change the current setting, refer to “Uconnect Settings” When enabled, the door locks will lock automatically when in “Understanding Your Instrument Panel”...
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 3. Repeat steps 1 and 2 for the opposite rear door. Unlock Child Protection Door Lock Lock Child Protection Door Lock WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are en- gaged.
Page 32: Keyless Enter-N-Go - Passive Entry
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE KEYLESS ENTER-N-GO — PASSIVE ENTRY The Passive Entry system is an enhancement to the vehi- cle’s Remote Keyless Entry system and a feature of Keyless Enter-N-Go. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • A lock request is made by the passive entry door handle To Unlock From The Passenger Side — If Equipped while a door is open. With a valid Passive Entry key fob within 5 ft (1.5 m) of the •...
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter The Trunk With a valid passive entry key fob within 5 ft (1.5 m) of the decklid, push the button located on the light bar between the license plate lamps. NOTE: If you inadvertently leave your vehicle’s passive entry key fob in the trunk and try to close the decklid, the decklid will automatically unlatch, unless another one of...
Page 35: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 The vehicle doors can also be locked by using the key fob lock button or the lock button located on the vehicle’s interior door panel. WINDOWS Power Windows The window controls on the driver’s door control all the door windows.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are single window controls on each passenger door To open the window part way, push the window switch to trim panel, which operate the passenger door windows. the first detent and release it when you want the window The window controls will operate only when the ignition is to stop.
Page 37: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: 3. Push the window switch down firmly to the second detent to open the window completely and continue to • If the window runs into any obstacle during auto- hold the switch down for an additional two seconds closure, it will reverse direction and then go back down.
Page 38: Trunk Lock And Release
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE the underside of the decklid overhang. The release feature will function only when the vehicle is in the unlock condition. With the ignition in the ON/RUN position, the trunk open symbol will display in the instrument cluster indicating that the trunk is open.
Page 39: Trunk Emergency Release
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Trunk Emergency Release Occupant Restraint Systems Features • Seat Belt Systems As a security measure, a trunk internal emergency release lever is built into the trunk latching mechanism. In the • Supplemental Restraint Systems (SRS) Air Bags event of an individual being locked inside the trunk, the •...
Page 40: Seat Belt Systems
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Children that are not big enough to wear the vehicle seat 9. If the air bag system in this vehicle needs to be modified belt properly (Refer to Child Restraints ) should be to accommodate a disabled person, refer to the “If You secured in a vehicle with a rear seat in child restraints or Need Assistance”...
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 risk of injury caused by striking the inside of the vehicle. BeltAlert Warning Sequence Everyone in a motor vehicle should be belted at all times. The BeltAlert warning sequence is activated when the Enhanced Seat Belt Use Reminder System (BeltAlert) vehicle is moving above a specified vehicle speed range and the driver or outboard front seat passenger is unbuck-...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The outboard front passenger seat BeltAlert is not active and reduce your risk of striking the inside of the vehicle or when the outboard front passenger seat is unoccupied. being thrown out of the vehicle. BeltAlert may be triggered when an animal or other items are placed on the outboard front passenger seat or when WARNING!
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! (Continued) WARNING! (Continued) driver, should always wear their seat belts whether can’t straighten a seat belt in your vehicle, take it to or not an air bag is also provided at their seating your authorized dealer immediately and have it position to minimize the risk of severe injury or fixed.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) wear your shoulder belt. The lap and shoulder belt are meant to be used together. • A frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across 5. Position the shoulder belt across the shoulder and chest your hips, below your abdomen.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: The adjustable upper shoulder belt anchorage is Seat Belt Extender equipped with an Easy Up feature. This feature allows the If a seat belt is not long enough to fit properly, even when shoulder belt anchorage to be adjusted in the upward the webbing is fully extended and the adjustable upper position without pushing or squeezing the release button.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Switchable Automatic Locking Retractor (ALR) ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in The seat belts in the passenger seating positions are this case and then carefully pull out only the amount of equipped with a Switchable Automatic Locking Retractor webbing necessary to comfortably wrap around the occu-...
Page 50: Supplemental Restraint Systems (Srs)
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode WARNING! (Continued) 1. Buckle the combination lap and shoulder belt. • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children 2.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • Steering Wheel and Column The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or • Instrument Panel it becomes disconnected prior to deployment. •...
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Air Bag Warning Light remains on after the four to Redundant Air Bag Warning Light eight-second interval. If a fault with the Air Bag Warning Light is • The Air Bag Warning Light comes on intermittently or detected, which could affect the Supplemental Restraint System (“SRS”), the Redundant Air Bag remains on while driving.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Front Air Bags WARNING! This vehicle has front air bags and lap/shoulder belts for • Being too close to the steering wheel or instrument both the driver and front passenger. The front air bags are a panel during front air bag deployment could cause supplement to the seat belt restraint systems.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The first stage inflator is triggered immediately during an WARNING! impact that requires air bag deployment. A low energy • No objects should be placed over or near the air bag output is used in less severe collisions. A higher energy output is used for more severe collisions.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Front Air Bag Operation The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as Front Air Bags are designed to provide additional protec- the air bags inflate to their full size.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The front passenger is not properly seated or his or her Occupant Classification Module (OCM) and Sensor weight is taken off of the seat for a period of time. The Occupant Classification Module (OCM) is located underneath the front passenger seat.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • Sitting in the center of the seat with their feet comfort- WARNING! ably on or near the floor • Never place a rear-facing child restraint in front of an • Sitting with their back against the seatback and the air bag.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not decrease OR increase the front passenger’s seated Examples of improper front passenger seating include: weight on the front passenger seat • The front passenger’s weight is transferred to another The front passenger’s seated weight must be properly part of the vehicle (like the door, arm rest or instrument positioned on the front passenger seat.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The OCS determines the front passenger’s most probable classification. If an occupant in the front passenger seat is seated improperly, the occupant may provide an output signal to the OCS that is different from the occupant’s properly seated weight input, for example: Not Seated Properly Not Seated Properly...
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Not Seated Properly Not Seated Properly WARNING! • If a child restraint system, child, small teenager or adult in the front passenger seat is seated improp- erly, the occupant may provide an output signal to the OCS that is different from the occupant’s prop- erly seated weight input.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 If the Air Bag Warning Light does not come on, or WARNING! (Continued) stays on after you start the vehicle, or it comes on as you • Always wear your seat belt and sit properly, with the drive, take the vehicle to an authorized dealer for seatback in an upright position, your back against service immediately.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not add a secondary seat cover or mat. Knee Impact Bolsters • At no time should any Supplemental Restraint System The Knee Impact Bolsters help protect the knees of the driver and front passenger, and position the front occu- (SRS) component or SRS related component or fastener pants for improved interaction with the front air bags.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Supplemental Side Air Bags When the SAB deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating SAB deploys Your vehicle is equipped with two types of side air bags: through the seat seam into the space between the occupant 1.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belted and seated properly, or if items are positioned in the area where the SABICs inflate. Children are at an even greater risk of injury from a deploying air bag. WARNING! • Do not stack luggage or other cargo up high enough to block the deployment of the SABICs.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 have deployed. Side Air Bags are a supplement to the seat WARNING! belt restraint system. Side Air Bags deploy in less time than • Side Air Bags need room to inflate. Do not lean it takes to blink your eyes.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Bags deploy independently; a left side impact deploys the sensing-system may also deploy the seat belt pretension- left Side Air Bags only and a right side impact deploys the ers, with or without the Side Air Bags, on both sides of the right Side Air Bags only.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • Seat Belt Pretensioners • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the • Seat Track Position Sensors process that generates the non-toxic gas used for air bag •...
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Enhanced Accident Response System Reset Procedure • Air bag covers may not be obvious in the interior trim, In order to reset the Enhanced Accident Response System but they will open during air bag deployment. functions after an event, the ignition switch must be •...
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 and safety systems for a short period of time, typically 30 WARNING! (Continued) seconds or less. The EDR in this vehicle is designed to • It is dangerous to try to repair any part of the air bag record such data as: system yourself.
Page 70: Child Restraints
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE law enforcement, that have the special equipment, can read There are different sizes and types of restraints for children the information if they have access to the vehicle or the from newborn size to the child almost large enough for an EDR.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Child Size, Height, Weight Or Age Of Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convert- younger and who have not reached ible Child Restraint, facing rearward the height or weight limits of their...
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infant And Child Restraints WARNING! Safety experts recommend that children ride rear-facing in • Never place a rear-facing child restraint in front of an the vehicle until they are two years old or until they reach air bag.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 All children whose weight or height is above the forward- WARNING! (Continued) facing limit for the child seat should use a belt-positioning • When your child restraint is not in use, secure it in booster seat until the vehicle’s seat belts fit properly.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Is the lap part of the belt as low as possible, touching the WARNING! child’s thighs and not their stomach? Never allow a child to put the shoulder belt under an 5.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Child + Child Anchors Only Anchors + Top...
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage...
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH child and the child restraint is 65 lbs anchorage system to attach...
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With LATCH Can two child restraints be attached Never “share” a LATCH anchorage using a common lower with two or more child restraints. If LATCH anchorage? the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat...
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Locating The LATCH Anchorages Locating The Upper Tether Anchorages The lower anchorages are round bars that are There are tether strap anchorages behind each found at the rear of the seat cushion where it rear seating position located in the panel be- meets the seatback, below the anchorage sym- tween the rear seatback and the rear window.
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems will be WARNING! (Continued) equipped with a rigid bar or a flexible strap on each side. for installing child seats in the outboard positions. Each will have a hook or connector to attach to the lower Please refer to “Installing The LATCH-Compatible anchorage and a way to tighten the connection to the Child Restraint System”...
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 2. Place the child seat between the lower anchorages for WARNING! that seating position. For some second row seats, you • Improper installation of a child restraint to the may need to recline the seat and / or raise the head restraint to get a better fit.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Vehicle Seat description in “Switchable Automatic Locking Retractors Belt (ALR)” under “Occupant Restraint Systems” for additional information on ALR. Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a Please see the table below and the following sections for lap/shoulder belt.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Please see the table below and the following sections for more information. Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for-...
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable 2. Pull enough of the seat belt webbing from the retractor Automatic Locking Retractor (ALR): to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 7. Finally, pull up on any excess webbing to tighten the lap Installing Child Restraints Using The Top Tether portion around the child restraint while you push the Anchorage child restraint rearward and downward into the vehicle seat.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
Page 87: Transporting Pets
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Automatic Locking Retractors (ALR)” under “Occupant WARNING! Restraint Systems” for additional information on ALR. • An incorrectly anchored tether strap could lead to Transporting Pets increased head motion and possible injury to the Air Bags deploying in the front seat could harm your pet.
Page 88: Safety Tips
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a SAFETY TIPS high-quality energy conserving type lubricant. Oil changes Transporting Passengers should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recom- NOTE: Never transport passengers in the cargo area.
Page 89: Exhaust Gas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Exhaust Gas Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is WARNING! damaged, have a competent mechanic inspect the complete Exhaust gases can injure or kill.
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light Floor Mat Safety Information The Air Bag Warning Light will turn on for four to Always use floor mats designed to fit the footwell of your eight seconds as a bulb check when the ignition is first vehicle.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 WARNING! (Continued) WARNING! (Continued) • ONLY install floor mats designed to fit your vehicle. • NEVER place any objects under the floor mat (e.g., NEVER install a floor mat that cannot be properly towels, keys, etc.).
Page 92: Periodic Safety Checks You Should Make Outside The Vehicle
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Modes Of Operation .....111 MIRRORS ......97 ▫...
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Easy Entry/Exit Seat ....124 ▫ Front Map/Reading Lights ....132 ▫...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 ▫ To Accelerate For Passing ....143 ▫ General Information .....161 ▫...
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ ParkSense Warning Display....173 ▫ Enabling And Disabling The ParkSense Active Park Assist System ....195 ▫...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 ▫ Troubleshooting Tips ....226 ▫ Opening Sunroof — Manual Mode ..232 ▫...
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Cargo Area — 60/40 Split-Folding STORAGE ......238 Rear Seat —...
Page 99: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 MIRRORS Automatic Dimming Mirror — If Equipped The mirror head can be adjusted up, down, left, and right Inside Day/Night Mirror — If Equipped for various drivers. The mirror should be adjusted to center The mirror head can be adjusted up, down, left, and right on the view through the rear window.
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Your vehicle may be transmitting data as authorized by the subscriber. • The 9–1–1 and ASSIST buttons will only function if you are connected to an operable 1X(voice/data) or 3G(data) network. Other Uconnect services will only be operable if your Uconnect Access service is active and you are connected to an operable 1X(voice/data) or 3G(data) network.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 9-1-1 Call 4. You should be able to speak with the 9-1-1 operator through the vehicle audio system to determine if addi- 1. Push the 9-1-1 Call button on the Rearview Mirror. tional help is needed. NOTE: In case the 9-1-1 Call button is pushed in error, there will be a 10 second delay before the 9-1-1 Call system WARNING!
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The 9-1-1 operator may attempt to contact appropriate WARNING! (Continued) emergency responders and provide them with impor- can cause the 9-1-1 Call system to fail, never add tant vehicle information and GPS coordinates. aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.) to your vehicle’s electri- WARNING!
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 9-1-1 Call System Limitations WARNING! Vehicles sold in Canada and Mexico DO NOT have 9-1-1 • Ignoring the rearview mirror light could mean you Call system capabilities. will not have 9-1-1 Call services. If the rearview 9-1-1 or other emergency line operators in Canada and mirror light is illuminated, have an authorized dealer Mexico may not answer or respond to 9-1-1 system calls.
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The vehicle battery loses power or becomes discon- NOTE: nected during a vehicle crash. • Your vehicle may be transmitting data as authorized by • 1X(voice/data) or 3G(data) network and/or Global Po- the subscriber.
Page 105: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Outside Mirrors Folding Feature CAUTION! All outside mirrors are hinged and may be moved either To avoid damage to the mirror during cleaning, never forward or rearward to resist damage. The hinges have spray any cleaning solution directly onto the mirror.
Page 106: Tilt Side Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Illuminated Entry lighting fades to off after about 30 Power Mirrors seconds or it will fade to off immediately once the ignition The power mirror controls are located on the driver’s door is placed into the RUN position.
Page 107: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature will be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear Win- dow Features”...
Page 108: Blind Spot Monitoring (Bsm) - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when The Blind Spot Monitoring (BSM) system uses two radar- the vehicle is in PARK.
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 NOTE: The BSM system does NOT alert the driver about Entering From The Side rapidly approaching vehicles that are outside the detection Vehicles that move into your adjacent lanes from either zones. side of the vehicle. The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function prop-...
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly (with a relative speed of side and enter the rear detection zone with a relative speed less than 15 mph (24 km/h) and the vehicle remains in the of less than 30 mph (48 km/h).
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in adjacent berms, etc.
Page 112: Rear Cross Path
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cross Path The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where the vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed.
Page 113: Modes Of Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 (5 km/h), to objects moving a maximum of approximately Modes Of Operation 20 mph (32 km/h), such as in parking lot situations. Three selectable modes of operation are available in the Uconnect System. Refer to “Uconnect Settings/Customer NOTE: In a parking lot situation, oncoming vehicles can Programmable Features”...
Page 114: General Information
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Whenever an audible alert is requested by the BSM 2. The device must accept any interference received, in- system, the radio is also muted. cluding interference that may cause undesired operation of the device. When the system is in RCP, the system shall respond with both visual and audible alerts when a detected object is Changes or modifications to any of these systems by other...
Page 115: Power Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Power Seats — If Equipped Adjusting The Seat Forward Or Rearward Some models may be equipped with a power driver’s seat. The seat can be adjusted both forward and rearward. Push The power seat switch is located on the outboard side of the seat switch forward or rearward.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Lumbar — If Equipped Vehicles equipped with power driver’s seat may be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward or rearward to increase or decrease the lumbar support.
Page 117: Manual Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Manual Seats — If Equipped While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have Manual Front Seat Forward/Rearward Adjustment reached the desired position.
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Seat Recline Adjustment WARNING! To adjust the seatback, lift the lever located on the outboard Do not ride with the seatback reclined so that the side of the seat, lean back to the desired position and shoulder belt is no longer resting against your chest.
Page 119: Front Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Front Heated Seats — If Equipped Vehicles Equipped With Remote Start The front heated seats control buttons are located within On models that are equipped with remote start, the heated the Uconnect system. You can gain access to the control seats can be programmed to come on during a remote start.
Page 120: Front Ventilated Seats - If Equipped
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Ventilated Seats — If Equipped Vehicles Equipped With Remote Start Located in the seat cushion and seat back are fans that On models that are equipped with remote start, the driv- draw the air from the passenger compartment and move er’s ventilated seat can be programmed to come on during air through fine perforations in the seat cover to help keep a remote start.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 NOTE: To remove the head restraint, raise it as far as it can WARNING! (Continued) go then push the release button and the adjustment button • Head restraints should never be adjusted while the at the base of each post while pulling the head restraint up.
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Head Restraints WARNING! The rear outboard head restraints have three positions Up, • A loose head restraint thrown forward in a collision Mid and Down. The center head restraint has only two or hard stop could cause serious injury or death to positions, Up and Down.
Page 123: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops to fold down either or both seatbacks. Head Restraint 1 — Release Button 2 — Adjustment Button Rear Seat Release Loops WARNING! NOTE: You may experience deformation in the seat cush-...
Page 124: Driver Memory Seat - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When returning the rear seatback to the upright position, The memory switch is located on the driver’s side door be sure the seatback is latched. panel. The switch contains three buttons, a set (S) button to activate the memory save function, the memory button (1) WARNING! and memory button (2).
Page 125: Programming The Memory Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Programming The Memory Feature NOTE: • Memory profiles can be set without the vehicle in PARK, To create a new memory profile, perform the following: but the vehicle must be in PARK to recall a memory NOTE: Saving a new memory profile will erase an existing profile.
Page 126: Memory Position Recall
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If a memory profile has not already been set, refer To recall the memory settings for driver two, push memory to Programming The Memory Feature in this section for button (2) or the unlock button on the key fob linked to instructions on how to set a memory profile.
Page 127: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • The Easy Entry/Easy Exit feature is disabled when the TO OPEN AND CLOSE THE HOOD driver seat position is less than 0.9 inches (22.7 mm) To open the hood, two levers must be released. forward of the rear stop.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the front of the vehicle. 3. Reach under the center front edge of the hood and push and hold the safety latch lever to the right. Safety Latch Lever Location Safety Latch Lever 4.
Page 129: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.
Page 130: Automatic Headlights - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped Headlight Time Delay This system automatically turns the headlights on or off This feature provides the safety of headlight illumination according to ambient light levels. To turn the system on, for up to 90 seconds (programmable) when leaving your rotate the headlight switch clockwise to the last detent for vehicle in an unlit area.
Page 131: Automatic High Beam Headlamp Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Automatic High Beam Headlamp Control — lever 6 full on/off cycles within 10 seconds of ignition ON. System will return to default setting upon ignition If Equipped off. The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automat- If the windshield or Automatic High Beam Headlamp ing high beam control through the use of a digital camera...
Page 132: Daytime Running Lights - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped Fog Lights — If Equipped The Daytime Running Lights come on whenever the en- The front fog light switch is built into the headlight switch. gine is running, and the transmission is not in the PARK position.
Page 133: Multifunction Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 NOTE: The fog lights will operate with the low beam Turn Signals headlights or parking lights on. However, selecting the Move the multifunction lever up or down and the arrows high beam headlights will turn off the fog lights. on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 134: Lane Change Assist
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Push the button once to turn the light on. Tap the lever up or down once, without moving beyond To turn the light off, push the button a second time. the detent, and the turn signal (right or left) will flash three times.
Page 135: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 operation after automatic battery protection is enabled (lights off), either place the ignition in the ON/RUN position or cycle the light switch. Instrument Panel Dimmer Control The instrument panel dimmer control is part of the head- light switch and is located on the drivers side of the instrument panel.
Page 136: Battery Saver Feature
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ambient Light Control — If Equipped Dome Light Position Rotate the ambient dimmer control upward or downward Rotate the instrument panel dimmer control completely to increase or decrease the brightness of the ambient light upward to the second detent to turn on the interior lights.
Page 137: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WINDSHIELD WIPERS AND WASHERS Windshield Wiper Operation The windshield wiper/washer controls are located on the Rotate the end of the lever to one of the first four detent windshield wiper/washer lever on the right side of the positions for intermittent settings, the fifth detent for low steering column.
Page 138: Intermittent Wiper System
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If snow packing occurs that obstructs the normal operation of the windshield wipers the following message will appear in the instrument cluster display: Front Wipers Blocked Cycle Switch or Clean the Windshield . It is important to remove the snow accumulation to allow the wipers to function normally and to maintain good visibil- ity of the road.
Page 139: Mist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Mist Use the Mist feature when weather conditions make occa- sional usage of the wipers necessary. Push the lever up- ward to the MIST position and release for a single wiping cycle. NOTE: The mist feature does not activate the washer pump;...
Page 140: Rain Sensing Wipers - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature can be turned on and off using Rain Sensing Wipers — If Equipped the Uconnect System, refer to “Uconnect Settings” in This feature senses moisture on the windshield and auto- “Understanding Your Instrument Panel”...
Page 141: Tilt/Telescoping Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 ignition switch in the RUN position, rain sensing wiper To unlock the steering column, pull the control handle operation can resume, if it has been selected, and no other down. To tilt the steering column, move the steering wheel inhibit conditions (mentioned previously) exist.
Page 142: Speed Control - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel control button is located within WARNING! the Uconnect system. You can gain access to the control • Persons who are unable to feel pain to the skin button through the climate screen or the controls screen. because of advanced age, chronic illness, diabetes, •...
Page 143: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 To Activate Push the on/off button to activate the speed control. The Cruise Indicator Light in the instrument cluster display will illuminate. To turn the system off, push the on/off button a second time. The Cruise Indicator Light will turn off.
Page 144: To Deactivate
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate U.S. Speed (mph) • Pushing the SET (+) button once will result in a 1 mph A soft tap on the brake pedal, pushing the CANC button or normal brake pressure while slowing the vehicle will increase in set speed.
Page 145: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 To Decrease Speed To Accelerate For Passing When the Speed Control is set, you can decrease speed by Press the accelerator as you would normally. When the pushing the SET (-) button. pedal is released, the vehicle will return to the set speed. The driver’s preferred units can be selected through the Using Speed Control On Hills instrument panel settings if equipped.
Page 146: Adaptive Cruise Control (Acc) - If Equipped
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADAPTIVE CRUISE CONTROL (ACC) — The Cruise Control system has two control modes: IF EQUIPPED • Adaptive Cruise Control mode for maintaining an ap- Adaptive Cruise Control (ACC) increases the driving con- propriate distance between vehicles. venience provided by cruise control while traveling on •...
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! (Continued) WARNING! (Continued) You should switch off the ACC system: operation of the vehicle under all road conditions. • When driving in fog, heavy rain, heavy snow, sleet, Your complete attention is always required while driving to maintain safe control of your vehicle.
Page 148: Adaptive Cruise Control (Acc) Operation
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Operation Activating Adaptive Cruise Control (ACC) The cruise control buttons (located on the right side of the You can only engage ACC if the vehicle speed is above steering wheel) operates the ACC system. 0 mph (0 km/h).
Page 149: To Activate/Deactivate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button. The ACC menu in the instrument cluster display will read “ACC Ready.” Adaptive Cruise Control Off WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.
Page 150: To Set A Desired Acc Speed
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set A Desired ACC Speed To Cancel When the vehicle reaches the speed desired, push the SET The following conditions cancel the system: (+) button or the SET (-) button and release. The instrument •...
Page 151: To Turn Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To Turn Off WARNING! The system will turn off and clear the set speed in memory The Resume function should only be used if traffic and road conditions permit. Resuming a set speed that •...
Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pushed, the set speed will U.S. Speed (mph) continue to increase in 5 mph increments until the • Pushing the SET (-) button once will result in a 1 mph button is released.
Page 153: Setting The Following Distance In Acc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 • When you use the SET (-) button to decelerate, if the speed. When driving up hill and down hill, the ACC engine’s braking power does not slow the vehicle suffi- system will cancel if the braking temperature exceeds ciently to reach the set speed, the brake system will normal range (overheated).
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Vehicle Indicator” icon, and the system will adjust the vehicle speed automatically to maintain the distance set- ting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
Page 156: Overtake Aid
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A Proximity Warning will alert the driver if ACC predicts Overtake Aid that its maximum braking level is not sufficient to maintain When driving with ACC engaged and following a vehicle, the set distance. If this occurs, a visual alert “BRAKE” will the system will provide an additional acceleration up to the flash in the instrument cluster display and a chime will ACC set speed to assist in passing the vehicle.
Page 157: Adaptive Cruise Control (Acc) Menu
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 While ACC is holding your vehicle at a standstill, if the Adaptive Cruise Control Ready driver seatbelt is unbuckled or the driver door is opened, When ACC is activated, but the vehicle speed setting has the parking brake will be activated, and the ACC system not been selected, the display will read “Adaptive Cruise will be cancelled.
Page 158: Display Warnings And Maintenance
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Display Warnings And Maintenance NOTE: If the “ACC/FCW Unavailable Wipe Front Radar Sensor” warning is active, Normal (Fixed Speed) Cruise “Wipe Front Radar Sensor In Front Of Vehicle” Control is still available. For additional information, refer Warning to “Normal (Fixed Speed) Cruise Control Mode”...
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • Do not attach or install any accessories near the sensor, “Clean Front Windshield” Warning including transparent material or aftermarket grilles. The “ACC/FCW Limited Functionality Clean Front Wind- Doing so could cause an ACC system failure or malfunc- shield”...
Page 160: Precautions While Driving With Acc
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the condition that created limited functionality is no Offset Driving longer present, the system will return to full functionality. ACC may not detect a vehicle in the same lane that is offset from your direct line of travel, or a vehicle merging in from NOTE: If the “ACC/FCW Limited Functionality Clean a side lane.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Turns And Bends Using ACC On Hills When driving on a curve with ACC engaged, the system When driving on hills, ACC may not detect a vehicle in may decrease the vehicle speed and acceleration for stabil- your lane.
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Changing Narrow Vehicles ACC may not detect a vehicle until it is completely in the Some narrow vehicles traveling near the outer edges of the lane in which you are traveling. In the illustration shown, lane or edging into the lane are not detected until they have ACC has not yet detected the vehicle changing lanes and it moved fully into the lane.
Page 163: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Stationary Objects And Vehicles Operation is subject to the following two conditions: ACC does not react to stationary objects and stationary 1. The device may not cause harmful interference. vehicles. For example, ACC will not react in situations 2.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting WARNING! To Increase Speed In the normal Cruise Control mode, the system will not When the Normal (Fixed Speed) Cruise Control is set, you react to vehicles ahead. In addition, the proximity can increase speed by pushing the SET (+) button.
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 • If the button is continually pushed, the set speed will Metric Speed (km/h) continue to increase in 10 km/h increments until the • Pushing the SET (-) button once will result in a 1 km/h button is released.
Page 166: Forward Collision Warning (Fcw) With Mitigation - If Equipped
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed potential frontal collision. The warnings and limited brak- ing are intended to provide the driver with enough time to To resume a previously set speed, push the RES button and react, avoid or mitigate the potential collision.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 • The FCW alerts may be triggered on objects other than system will hold the vehicle at standstill for two seconds and then release the brakes. vehicles such as guard rails or sign posts based on the course prediction.
Page 168: Turning Fcw On Or Off
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Changing the FCW status to “off” prevents the system Turning FCW On Or Off from warning you of a possible collision with the vehicle NOTE: The default status of FCW is “on”. This allows the in front of you.
Page 169: Fcw Limited Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 you when you are farther away and it applies limited condition that limits FCW functionality. Although the braking. This gives you the most reaction time to avoid a vehicle is still drivable under normal conditions, the active possible collision.
Page 170: Turning Lanesense On Or Off
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When both lane markings are detected and the driver Turning LaneSense On Or Off unintentionally drifts out of the lane (no turn signal The default status of LaneSense is “off”. applied), the LaneSense system provides a haptic warning The LaneSense button is located on the switch panel below in the form of torque applied to the steering wheel to the Uconnect display.
Page 171: Lanesense Warning Message
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 To turn the LaneSense system on, push the LaneSense LaneSense Warning Message button (LED turns off). A “Lane Sense On” message is The LaneSense system will indicate the current lane drift shown in the instrument cluster display. condition through the instrument cluster display.
Page 172 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Left Lane Departure — Only Left Lane Detected • When the LaneSense system is on, the LaneSense indi- cator is solid white when only the left lane marking has been detected and the system is ready to provide visual warnings in the instrument cluster display if an unin- tentional lane departure occurs.
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 • When the LaneSense system senses a lane drift situation, Left Lane Departure — Both Lanes Detected the left thick lane line and left thin line turn solid yellow. • When the LaneSense system is on, the lane lines turn The LaneSense indicator changes from solid green to from gray to white to indicate that both of the lane solid yellow.
Page 174: Changing Lanesense Status
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LaneSense system senses the lane has been Changing LaneSense Status approached and is in a lane departure situation, the left The LaneSense system settings can be configured through thick lane line flashes yellow (on/off) and the left thin the Uconnect system screen.
Page 175: Parksense Rear Park Assist - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 PARKSENSE REAR PARK ASSIST — IF EQUIPPED ParkSense Sensors The ParkSense Rear Park Assist system provides visual and The four ParkSense sensors, located in the rear fascia/ audible indications of the distance between the rear fascia bumper, monitor the area behind the vehicle that is within and a detected obstacle when backing up, e.g.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle. If an obstacle is detected in the center rear region, the display will show a single solid arc in the center rear region and will produce a one-half second tone.
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Slow Tone/Solid Arc Slow Tone/Solid Arc...
Page 178 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING ALERTS Rear Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than Distance than (200-150 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (inches/cm) 79 inches (30 cm) (200 cm) Arcs —...
Page 180: Enabling And Disabling Parksense
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling And Disabling ParkSense The ParkSense switch LED will be on when ParkSense is disabled or requires service. The ParkSense switch LED ParkSense can be enabled and disabled with the ParkSense will be off when the system is enabled. If the ParkSense switch, located on the switch panel below the Uconnect switch is pushed, and requires service, the ParkSense display.
Page 181: Cleaning The Parksense System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 • When you move the gear selector to the REVERSE is clean and clear of snow, ice, mud, dirt or other obstruc- tion and then cycle the ignition. If the message continues to position and ParkSense is turned OFF, the instrument appear, see an authorized dealer.
Page 182: Parksense Front And Rear Park Assist - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE FRONT AND REAR PARK ASSIST — WARNING! IF EQUIPPED Drivers must be careful when backing up even when The ParkSense Park Assist system provides visual and using ParkSense. Always check carefully behind your audible indications of the distance between the rear and/or vehicle, look behind you, and be sure to check for front fascia and a detected obstacle when backing up or...
Page 183: Parksense Sensors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 • The automatic braking function may not be applied fast Refer to ParkSense System Usage Precautions for limita- enough for obstacles that move toward the rear of the tions of this system and recommendations. vehicle from the left and/or right sides.
Page 184: Parksense Warning Display
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If your vehicle is equipped with the ParkSense ParkSense Display Active Park Assist system, six sensors will be located in the Rear Park Assist rear fascia/bumper. Refer to the ParkSense Active Park When the vehicle is in REVERSE and an obstacle has been Assist System section for further information.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Single 1/2 Second Tone/Solid Arc Slow Tone/Solid Arc...
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Slow Tone/Solid Arc Fast Tone/Flashing Arc...
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 188 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING ALERTS Rear Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than Distance than (200-150 (150-120 (120-100 (100-65 cm) (65-30 cm) 12 inches (in/cm) 79 inches (30 cm) (200 cm) Arcs —...
Page 189 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Front Park Assist When the vehicle is in DRIVE the ParkSense Warning screen will be displayed when an obstacle is detected. The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle.
Page 190 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE No Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 191 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING ALERTS Front Distance Greater than 47-39 inches 39-25 inches 25-12 inches Less than (in/cm) 47 inches (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (30 cm) (120 cm) Arcs — Left None None None 2nd Flashing...
Page 193: Enabling And Disabling Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Enabling And Disabling ParkSense The ParkSense switch LED will be on when ParkSense is disabled or requires service. The ParkSense switch LED ParkSense can be enabled and disabled with the ParkSense will be off when the system is enabled. If the ParkSense switch, located on the switch panel below the Uconnect switch is pushed, and requires service, the ParkSense display.
Page 194: Cleaning The Parksense System
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR SENSORS , PARKSENSE UNAVAILABLE WIPE ParkSense System Usage Precautions FRONT SENSORS , or PARKSENSE UNAVAILABLE SER- NOTE: VICE REQUIRED messages if an object is detected within • Ensure that the front and rear bumper are free of snow, the five second pop-up duration.
Page 195 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 obstacle behind or in front of the fascia/bumper, or it CAUTION! could provide a false indication that an obstacle is • ParkSense is only a parking aid and it is unable to behind or in front of the fascia/bumper. recognize every obstacle, including small obstacles.
Page 196: Parksense Active Park Assist System - If Equipped
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • During a semi-automatic maneuver, if the driver touches PARKSENSE ACTIVE PARK ASSIST SYSTEM — the steering wheel after being instructed to remove their IF EQUIPPED hands from the steering wheel, the system will cancel, The ParkSense Active Park Assist system is intended to and the driver will be required to manually complete the assist the driver during parallel and perpendicular parking...
Page 197: Enabling And Disabling The Parksense Active Park Assist System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Enabling And Disabling The ParkSense Active Park The ParkSense Active Park Assist system will turn off automatically for any of the following conditions: Assist System • The parking maneuver is completed. The ParkSense Active Park Assist system can be enabled and disabled with the ParkSense Active Park Assist switch, •...
Page 198: Parallel Parking Space Assistance Operation/Display
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ParkSense Active Park Assist system will only operate Parallel Parking Space Assistance Operation/ and search for a parking space when the following condi- Display tions are present: When the ParkSense Active Park Assist system is enabled •...
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 • When seeking for a parking space, the driver should When an available parking space has been found, and the drive as parallel or perpendicular (depending on the vehicle is not in position, you will be instructed to move type of maneuver) to other vehicles as possible.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ParkSense Active Park Assist system will allow a When the vehicle has reached the end of its backward maximum of six shifts between DRIVE or REVERSE. If movement, the system will instruct the driver to check the maneuver cannot be completed within six shifts, the their surroundings and stop the vehicle’s movement.
Page 203 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 NOTE: It is the drivers responsibility to use the brake and When the driver places the gear selector into the DRIVE stop the vehicle. The driver should check their surround- position, the system may instruct the driver to wait for ings and be prepared to stop the vehicle either when steering to complete.
Page 204 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will then instruct the driver to check their When the vehicle has reached the end of its forward surroundings and move forward. movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement.
Page 205 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will then instruct the driver to check their Your vehicle is now in the parallel park position. When the surroundings and move backward. maneuver is complete, the driver will be instructed to check the vehicle’s parking position.
Page 207: Perpendicular Parking Space Assistance Operation/Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Perpendicular Parking Space Assistance Operation/Display When the ParkSense Active Park Assist system is enabled, the “Active ParkSense Searching - Push OK for Perpen- dicular Park” message will show in the instrument cluster display. Push the OK button on the left side steering wheel switch to change your parking space setting to a perpen- dicular maneuver.
Page 208 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The driver needs to make sure that the selected parking When an available parking space has been found, and the space for the maneuver remains free and clear of any vehicle is not in position, you will be instructed to move obstructions (e.g.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 210 208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 • The ParkSense Active Park Assist system will allow a When the vehicle has reached the end of its backward maximum of six shifts between DRIVE or REVERSE. If movement, the system will instruct the driver to check the maneuver cannot be completed within six shifts, the their surroundings and stop the vehicle’s movement.
Page 212 210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the DRIVE be instructed to place the gear selector into the DRIVE position, the system may instruct the driver to wait for position.
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 The system will then instruct the driver to check their When the vehicle has reached the end of its forward surroundings and move forward. movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 215 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 The system will then instruct the driver to check their Your vehicle is now in the perpendicular park position. surroundings and move backward. When the maneuver is complete, the driver will be in- structed to check the vehicle’s parking position.
Page 216: Parkview Rear Back Up Camera - If Equipped
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) • The vehicle must be driven slowly when using the Drivers must be careful when performing parallel or ParkSense Active Park Assist system in order to be perpendicular parking maneuvers even when using able to stop in time when an obstacle is detected.
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 NOTE: The ParkView Rear Back Up Camera has program- When the vehicle is shifted out of REVERSE (with camera mable modes of operation that may be selected through the delay turned on), the camera image will continue to be Uconnect System.
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following table shows the approximate distances for each zone: Zone Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green 6.5 ft or greater (2 m or greater) NOTE: If snow, ice, mud, or any foreign substance builds...
Page 219: Overhead Console
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Power sunroof and power sunshade switches may also be included, if equipped. Overhead Console — Power Sunroof Front Map/Reading Lights The front map/reading lights are mounted in the overhead console.
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights — With Center Buttons Front Map/Reading Lights — With Push Lenses There are two map/reading light buttons located in the The two map/reading lights can be operated indepen- center of the overhead console that allow the lights to dently by pushing the lenses.
Page 221: Sunglass Bin Door
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Sunglass Bin Door The overhead console has a compartment which provides storage for a pair of sunglasses. Your vehicle may be equipped with a rear mounted or front mounted sunglass bin door. The storage compartment access is a “push/push” design. Push the chrome pad on the sunglass bin door to open.
Page 222 220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons that are located in the sun visor WARNING! designate the three different HomeLink channels. • Your motorized door or gate will open and close The HomeLink indicator is located above the center button. while you are training the universal transceiver.
Page 223: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Before You Begin Programming HomeLink Programming A Rolling Code Be sure that your vehicle is parked outside of the garage For programming garage door openers that were manufac- before you begin programming. tured after 1995: For more efficient programming and accurate transmission These garage door openers can be identified by the “LEARN”...
Page 224 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Place the ignition in the ON/RUN position. garage door openers/devices there may be a light that blinks when the garage door opener/device is in the NOTE: For vehicles equipped with Keyless Enter-N-Go, LEARN/TRAIN mode.
Page 225: Programming A Non-Rolling Code
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 NOTE: For vehicles equipped with Keyless Enter-N-Go, 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) place the ignition in the RUN position with the engine ON. away from the HomeLink button you wish to program Make sure while programming HomeLink with the engine while keeping the HomeLink indicator light in view.
Page 226: Canadian/Gate Operator Programming
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink Button Canadian radio frequency laws require transmitter signals (Non-Rolling Code) to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink to pick up To reprogram a channel that has been previously trained, the signal during programming.
Page 227: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 4. Watch for the HomeLink indicator to change flash rates. NOTE: For vehicles equipped with Keyless Enter-N-Go, When it changes, it is programmed. It may take up to 30 place the ignition in the RUN position with the engine ON. seconds or longer in rare cases.
Page 228: Troubleshooting Tips
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To do this, push and hold the two outside buttons for 20 WARNING! seconds until the red indicator flashes. Note that all chan- • Vehicle exhaust contains carbon monoxide, a danger- nels will be erased. Individual channels cannot be erased. ous gas.
Page 229: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion.
Page 230: Opening Sunroof - Express
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Manual Mode WARNING! (Continued) To open the sunroof, push and hold the switch rearward. equipped with Keyless Enter-N-Go in the ACC or Sunroof will move rearward and automatically stop at full ON/RUN mode.
Page 231: Pinch Protect Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 Pinch Protect Feature Wind Buffeting This feature will detect an obstruction in the opening of the Wind buffeting can be described as the perception of sunroof during Express Close operation. If an obstruction pressure on the ears or a helicopter-type sound in the ears.
Page 232: Relearn Procedure
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Relearn Procedure POWER SUNROOF WITH POWER SHADE — IF EQUIPPED For vehicles equipped with a single-pane sunroof, there is a relearn procedure that allows you to calibrate the sunroof The power sunroof switches are located to the left between when the “Express Operation”...
Page 233: Opening Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 The power shade switches are located to the right between WARNING! (Continued) the sun visors on the overhead console. children, can become entrapped by the power sunroof while operating the power sunroof switch. Such en- trapment may result in serious injury or death.
Page 234: Opening Sunroof - Manual Mode
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Manual Mode Venting Sunroof — Express To open the sunroof, push and hold the switch rearward. Push and release the Vent button within one-half second The sunroof will (if the sunshade is in the closed position and the sunroof will open to the vent position.
Page 235: Closing Power Shade - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 and the shade will open automatically to the full-open Pinch Protect Feature position. Any release of the switch will stop the movement This feature will detect an obstruction in the opening of the and the shade will remain in a partially opened condition sunroof during Express Close operation.
Page 236: Sunroof Maintenance
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance POWER OUTLETS — IF EQUIPPED Use only a non-abrasive cleaner and a soft cloth to clean the Your vehicle is equipped with 12 Volt (13 Amp) power glass panel. outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories.
Page 237 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Front Power Outlet Front Center Console Outlet In addition to the front power outlet, there is also a power NOTE: To ensure proper operation a MOPAR cigar knob outlet located in the storage area of the center console. and element must be used.
Page 238 236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! • Do not exceed the maximum power of 160 Watts (13 • Many accessories that can be plugged in draw power Amps) at 12 Volts. If the 160 Watt (13 Amp) power from the vehicle’s battery, even when not in use (i.e., rating is exceeded the fuse protecting the system will cellular phones, etc.).
Page 239: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the forward wall of the center console storage bin, below the media center. This outlet can power cellular phones, elec- tronics and other low power devices requiring power up to 150 Watts.
Page 240: Cupholders
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Cupholders WARNING! (Continued) The rear seat cupholders are located in the center armrest • Do not touch with wet hands. between the rear seats. The cupholders are positioned • Close the lid when not in use. forward in the armrest and side-by-side to provide conve- •...
Page 241: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 NOTE: The glove compartment handle is equipped with a Console Features lock. To lock the glove compartment, remove the emergency There is a storage compartment located under the center key from the key fob, insert emergency key into glove console armrest.
Page 242 240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull upward on the release handle, located on the front of the armrest, to open the storage compartment. The armrest can be slid forward/rearward to allow driver/ passenger comfort position. WARNING! Do not operate this vehicle with a console compart- ment lid in the open position.
Page 243 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 Located inside the center console storage compartment is a line that indicates how much storage is allowed. Front Center Console Storage Storage Compartment Fill Line NOTE: Filling the console storage area above this line may impede the sliding of the cupholder.
Page 244 242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Located inside the front of the console storage area power cords can be routed from the storage area to the center console pass-through. Front Center Console Pass-Through Center Console Storage Passage...
Page 245: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 Door Storage Rear Seat Armrest Storage — If Equipped The door panels contain storage areas with a bottle holder. For rear passengers there is a storage bin located in the armrest. Lift upward on the latch to open the storage compartment.
Page 246: Cargo Area Features
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES After releasing the seatback, it can be folded forward. Cargo Area — 60/40 Split-Folding Rear Seat — If Equipped The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling the seatback loops between the seatbacks and the bolsters.
Page 247 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 WARNING! WARNING! (Continued) The weight and position of cargo and passengers can • Be certain that the seatback is securely locked into change the vehicle center of gravity and vehicle han- position. If the seatback is not securely locked into dling.
Page 248: Cargo Net Hooks
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Net Hooks The rear cargo area is equipped with cargo net hooks, located on either side of the rear cargo area. Lower Cargo Net Hook CAUTION! Do not exceed the maximum weight limit 35 lbs (16 kg) Upper Cargo Net Hook of the cargo net hook.
Page 249: Ski Pass-Through
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 Ski Pass-Through REAR WINDOW FEATURES There is a ski pass-through door located behind the rear Rear Window Defroster seat armrest that allows longer items, such as snow skis, to The rear window defroster button is located on the be stored in the rear cargo area.
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ...251 CYBERSECURITY ......291 INSTRUMENT CLUSTER .
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Voice Text Reply ..... . .339 CLIMATE CONTROLS ....317 ▫...
Page 253: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 251 INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Radio Screen 11 — Steering Wheel 2 — Instrument Cluster Display Controls 7 — Passenger Air Bag 12 — Hood Release 3 — Instrument Cluster 8 — Glove Compartment 13 —...
Page 254: Instrument Cluster
252 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster — Base...
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 253 Instrument Cluster — Premium...
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL • The gauge pointer will likely indicate a higher tem- 1. Tachometer • Indicates the engine speed in revolutions per minute perature when driving in hot weather or up mountain grades. It should not be allowed to exceed the upper (RPM x 1000).
Page 257: Warning And Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 255 WARNING AND INDICATOR LIGHTS The warning / indicator lights switch on in the instrument panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner’s Manual, which you are advised to read carefully in all cases.
Page 258: Red Telltale Indicator Lights
256 UNDERSTANDING YOUR INSTRUMENT PANEL Red Telltale Indicator Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition is first placed in the ON/RUN position, if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on.
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 257 Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake appli- cation. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by WARNING! placing the ignition in the ON/RUN position. The light should illuminate for approximately two seconds. The light Driving a vehicle with the red brake light on is should then turn off unless the parking brake is applied or dangerous.
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 Vehicle Security Warning Light — If Equipped Red Telltale What It Means Light Vehicle Security Warning Light — If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.
Page 262 260 UNDERSTANDING YOUR INSTRUMENT PANEL Battery Charge Warning Light Red Telltale What It Means Light Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact your authorized dealer as soon as possible.
Page 263 UNDERSTANDING YOUR INSTRUMENT PANEL 261 Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash depending on the nature of the problem.
Page 264 262 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with se- vere usage. If this light turns on, safely pull over and stop the vehicle. Then, place the transmission into NEUTRAL and run the engine at idle speed or apply light foot pressure to increase the engine speed RPM until the Transmission Temperature light turns off.
Page 265 UNDERSTANDING YOUR INSTRUMENT PANEL 263 Electric Power Steering Fail Warning Light — If Equipped Red Telltale What It Means Light Electric Power Steering Fail Warning — If Equipped This light is used to manage the electrical warning of the EPS (Electric Power Steering). Refer to “Power Steering”...
Page 266: Yellow Telltale Indicator Lights
264 UNDERSTANDING YOUR INSTRUMENT PANEL Trunk Open Warning Light Red Telltale What It Means Light Trunk Open Warning Light This indicator will illuminate when the trunk is open and not fully closed. NOTE: If the vehicle is moving, there will also be a single chime. Yellow Telltale Indicator Lights Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale...
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.
Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition is placed in the ON/RUN position, and when ESC is activated.
Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off. Low Washer Fluid Indicator Light —...
Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Monitoring Indicator Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 Please note that the TPMS is not a substitute for proper tire CAUTION! maintenance, and it is the driver’s responsibility to main- tain correct tire pressure, even if under-inflation has not The TPMS has been optimized for the original equip- reached the level to trigger illumination of the TPMS low ment tires and wheels.
Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL Electric Park Brake Fail Light Yellow Telltale What It Means Light Electric Park Brake Fail Warning Light This telltale will turn on to indicate the Electric Park Brake is not functioning properly and that service is required. Contact your authorized dealership. Low Fuel Indicator Light Yellow Telltale What It Means...
Page 273 UNDERSTANDING YOUR INSTRUMENT PANEL 271 Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
Page 274 272 UNDERSTANDING YOUR INSTRUMENT PANEL Service Forward Collision Warning Indicator Light — If Equipped Yellow Telltale What It Means Light Service Forward Collision Warning Indicator Light This light indicates a potential system fault with the FCW system. Refer to “Adaptive Cruise Control (ACC)”...
Page 275 UNDERSTANDING YOUR INSTRUMENT PANEL 273 LaneSense Failure Indicator Light — If Equipped Yellow Telltale What It Means Light LaneSense Failure Indicator Light This light will turn on when the LaneSense system is not operating and needs service. Please see your authorized dealer. Service AWD Indicator Light —...
Page 276: Green Telltale Indicator Lights
274 UNDERSTANDING YOUR INSTRUMENT PANEL Service Adaptive Cruise Control Light Yellow Telltale What It Means Light Service Adaptive Cruise Control Light This light will turn on when ACC is not operating and needs service. For further information, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle.” Green Telltale Indicator Lights Park/Headlight On Indicator Light Green Telltale...
Page 277 UNDERSTANDING YOUR INSTRUMENT PANEL 275 Stop/Start Active Indicator Light — If Equipped Green Telltale What It Means Light Stop/Start Active Indicator Light — If Equipped This telltale will illuminate when the Stop/Start function is in “Autostop” mode. LaneSense Indicator Light — If Equipped Green Telltale What It Means Light...
Page 278 276 UNDERSTANDING YOUR INSTRUMENT PANEL Turn Signal Indicator Lights Green Telltale What It Means Light Turn Signal Indicator Lights The instrument cluster directional arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function lever is moved down (left) or up (right).
Page 279: White Telltale Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 277 White Telltale Indicator Lights Cruise Control Ready Indicator Light White Telltale What It Means Light Cruise Control Ready Indicator Light This light will turn on when the electronic speed control is on, but not set. Cruise Control Cancelled Light White Telltale What It Means...
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Ready Light — If Equipped White Telltale What It Means Light Adaptive Cruise Control (ACC) Ready Light — If Equipped This light will turn on when Adaptive Cruise Control (ACC) has been turned on. Refer to “Adap- tive Cruise Control ”...
Page 281: Blue Telltale Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Adaptive Cruise Control (ACC) Distance Ready Display Light — If Equipped White Telltale What It Means Light Adaptive Cruise Control (ACC) Distance Setting Display Light — If Equipped This light will turn on when the Adaptive Cruise Control (ACC) is ready, but not set. Refer to “Adaptive Cruise Control (ACC)”...
Page 282: Instrument Cluster Display
280 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Your vehicle is equipped with an interactive cluster dis- play, located in the instrument cluster, which offers useful information to the driver. With the ignition in the STOP/ OFF position, the opening/closing of a door will activate the display for viewing, and display the total miles or kilometers in the odometer.
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 281 • Messages • Up Arrow Button • Screen Setup Push and release the up arrow button to scroll upward through the Main Menu items. • Settings The system allows the driver to select information by •...
Page 284: Oil Change Reset
282 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Reset 3. Without pushing the brake pedal, push the ENGINE START/STOP button once to return the ignition to the Oil Change Due OFF/LOCK position. Your vehicle is equipped with an engine oil change indi- The Oil Life can also be reset through the instrument cator system.
Page 285: Instrument Cluster Display Messages
UNDERSTANDING YOUR INSTRUMENT PANEL 283 • Tire Pressure Screen With Low Tire(s) “Inflate Tire to XX” Instrument Cluster Display Messages • Front Seatbelts Unbuckled • Service Tire Pressure System • Driver Seatbelt Unbuckled • Parking Brake Engaged • Passenger Seatbelt Unbuckled •...
Page 286: Instrument Cluster Display Menu Items
284 UNDERSTANDING YOUR INSTRUMENT PANEL • Remote Start Aborted Fuel Low • Engage Park Brake to Prevent Rolling • Remote Start Aborted Too Cold • Washer Fluid Low • Remote Start Aborted Door Open The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the •...
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 Tire Pressure Driver Assist Push and release the up or down arrow button until the If tire pressure is OK for all tires, a vehicle icon is displayed Vehicle Info menu displays in the instrument cluster dis- with tire pressure values in each corner of the icon.
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL Push the SET + or the SET- button (located on the steering LaneSense Menu — If Equipped wheel) and the following will display in the information The instrument cluster display displays the current La- display: neSense system settings.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 Trip Info Screen Setup Push and release the up or down arrow button until the Push and release the up or down arrow button until the Trip Menu item is highlighted in the instrument cluster Screen Setup Menu displays in the instrument cluster display (toggle left or right arrow button to select Trip A or display.
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL • Current Economy Upper Right • None • Trip A • Compass (default — Premium) • Trip B • Outside Temp (default — Base) • Audio Information • Time • Menu Title (Default) • Range •...
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 Vehicle Settings — If Equipped Translation Settings Submenu Message Push and release the up or down arrow button until the Vehicle Settings Menu displays in the instrument cluster Volume display. Push OK button to enter the setting, select from list Rear Parksense On/Off...
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL Translation Translation Settings Submenu Settings Submenu Message Message Key Fob Key In On, Off Headlights Lights On, Off Linked To Memory On With W/Wipers Memory Wipers Remote Start Rmt Start Off, Remote Rain Sensing Auto Wipers On, Off Comfort Comfort...
Page 293: Cybersecurity
UNDERSTANDING YOUR INSTRUMENT PANEL 291 Vehicle software technology continues to evolve over time Translation Settings Submenu and FCA US LLC, working with its suppliers, evaluates Message and takes appropriate steps as needed. Similar to a com- Compass Compass Var See Owner’S puter or other devices, your vehicle may require software Variance Manual, X...
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: WARNING! (Continued) • FCA or your dealer may contact you directly regarding • ONLY insert media (e.g., USB, SD card, or CD) into software updates. your vehicle if it came from a trusted source. Media of unknown origin could possibly contain malicious •...
Page 295: Uconnect Settings
UNDERSTANDING YOUR INSTRUMENT PANEL 293 UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access and change the customer programmable features. Uconnect 8.4 Buttons On Touchscreen And Buttons On Faceplate 1 —...
Page 296: Buttons On The Faceplate
294 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons On The Faceplate the faceplate and press the Settings button on the touch- screen. The remaining settings are defined for the Uconnect Buttons are located below the Uconnect system in the center 8.4/8.4 NAV — Press the “Apps” button on the touch- of the instrument panel.
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options Units Metric Touchscreen Beep Navigation Turn-By-Turn In Cluster — If Equipped NOTE: When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in- strument cluster display as the vehicle approaches a designated turn within a programmed route. Voice Brief Detailed...
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 Setting Name Selectable Options Set Time Minutes NOTE: The “Set Time Minutes” feature will allow you to adjust the minutes. The “Sync time with GPS” button on the touch- screen must be unchecked. Time Format 12hrs 24hrs Show Time in Status Bar —...
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options ParkView Backup Camera Active Guidelines — If Equipped NOTE: The “ParkView Backup Camera Active Guide Lines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position when the option is checked.
Page 301 UNDERSTANDING YOUR INSTRUMENT PANEL 299 Setting Name Selectable Options Forward Collision Warning On/Off — If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. The FCW system state is kept in memory from one ignition cycle to the next.
Page 302 300 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display NOTE: The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in RE- VERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or visual) to indicate the proximity to other objects.
Page 303 UNDERSTANDING YOUR INSTRUMENT PANEL 301 Setting Name Selectable Options Blind Spot Alert — Lights Lights and Chime If Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Monitor (BSM) system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options LaneSense Strength — Medium High If Equipped Electric Park Brake Ser- vice Mode — If Equipped NOTE: The “Electric Park Brake Service Mode” feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven system, to command the electric park brake retraction, to service the rear foundation brakes (brake pads, calipers, rotors, etc.).
Page 305 UNDERSTANDING YOUR INSTRUMENT PANEL 303 Setting Name Selectable Options Headlights With Wipers — If Equipped Headlight Illumi- 0 sec 30 sec 60 sec 90 sec nated On Approach NOTE: When the “Headlight Illumination On Approach” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the doors are unlocked with the key fob.
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks NOTE: When the “Auto Door Locks” feature is selected, all doors will lock automatically when the vehicle reaches a speed of 12 mph (20 km/h).
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 Setting Name Selectable Options Flash Lights With Lock Sound Horn With Lock 1st Press 2nd Press Sound Horn With Remote Start 1st Press Of Key Fob Unlocks Driver Door All Doors NOTE: When Driver Door is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first press of the key fob unlock button.
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options Personal Settings Linked To Key Fob — If Equipped NOTE: The “Settings Linked To Key Fob” feature provides automatic recall of all settings stored to a memory location (driv- er’s seat, exterior mirrors, steering column position and radio station pre-sets) to enhance driver mobility when enter- ing and exiting the vehicle.
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 Engine Off Options After pressing the “Engine Off Options” button on the touchscreen the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 311 UNDERSTANDING YOUR INSTRUMENT PANEL 309 Setting Name Selectable Options Surround Sound — If Equipped AUX Volume Offset — If Equipped NOTE: This feature provides the ability to tune the audio level for portable devices connected through the AUX input. Loudness — If Equipped Phone/Bluetooth After pressing the “Phone/Bluetooth”...
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL SiriusXM Setup After pressing the “SiriusXM Setup” button on the touch- screen the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL Clear Personal Data After pressing the “Clear Personal Data” button on the touchscreen the following settings will be available: Setting Name Selectable Options Clear Personal Data Cancel NOTE: When the “Clear Personal Data” feature is selected it will remove all personal data including Bluetooth devices and presets.
Page 315: Uconnect Radios - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 313 UCONNECT RADIOS — IF EQUIPPED For detailed information about your Uconnect radio, refer to your Uconnect Owner’s Manual Supplement. USB PORT AND AUX JACK — IF EQUIPPED Located in the front storage area of the center console, this feature allows an external device, to be connected to the audio system.
Page 316: Steering Wheel Audio Controls - If Equipped
314 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and IF EQUIPPED mode of the sound system. Pushing the top of the rocker The remote sound system controls are located on the rear switch will increase the volume, and pushing the bottom of surface of the steering wheel.
Page 317: Radio Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 315 Radio Operation RADIO OPERATION AND MOBILE DEVICES Pushing the top of the switch will “Seek” up for the next Under certain conditions, an “on” mobile device in your listenable station and pushing the bottom of the switch will vehicle can cause erratic or noisy performance from your “Seek”...
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL The radio manufacturer believes the internal wireless radio NOTE: is safe for use by consumers. The level of energy emitted is • This equipment has been tested and found to comply far less than the electromagnetic energy emitted by wire- with the limits for a Class B digital device, pursuant to less devices such as mobile phones.
Page 319: Climate Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 317 CLIMATE CONTROLS Climate Controls Without A Touchscreen Overview The Climate Control System allows you to regulate the temperature, airflow, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel below the radio.
Page 320 318 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Controls Without A Touchscreen Description Icon Description A/C Button Push and release to change the current setting, the indicator illuminates when A/C is ON. Per- forming this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 Icon Description Blower Control Knob Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using the blower control knob on the faceplate.
Page 322 320 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 323: Climate Controls With A Touchscreen Overview
UNDERSTANDING YOUR INSTRUMENT PANEL 321 Climate Controls With A Touchscreen Overview Manual Climate Controls With A Uconnect 5.0 Touchscreen...
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Climate Controls With A Uconnect 5.0 Touchscreen...
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 Automatic Climate Controls With A Uconnect 8.4/8.4 NAV Touchscreen...
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Controls With A Touchscreen Description Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 Icon Description AUTO Button — If Equipped Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Performing this function will cause the system to switch between manual mode and automatic modes. Refer to “Automatic Operation” for more information. Front Defrost Button Press and release to change the current airflow setting to Defrost mode.
Page 328 326 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Description SYNC Button — If Equipped Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger tempera- ture setting with the driver temperature setting.
Page 329 UNDERSTANDING YOUR INSTRUMENT PANEL 327 Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 330 328 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control Functions MAX A/C A/C (Air Conditioning) MAX A/C sets the control for maximum cooling performance. The Air Conditioning (A/C) button allows the operator to Press and release to toggle between MAX A/C and the prior manually activate or deactivate the air conditioning sys- settings.
Page 331: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 329 NOTE: In cold weather, use of recirculation mode may lead 3. When the system is set up for your comfort level, it is to excessive window fogging. The recirculation feature not necessary to change the settings. You will experience may be unavailable (button on the touchscreen greyed out) the greatest efficiency by simply allowing the system to if conditions exist that could create fogging on the inside of...
Page 332: Operating Tips
330 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation Override Winter Operation This system offers a full complement of manual override To ensure the best possible heater and defroster perfor- features. The AUTO symbol in the front ATC display will mance, make sure the engine cooling system is functioning be turned off when the system is being used in the manual properly and the proper amount, type, and concentration mode.
Page 333 UNDERSTANDING YOUR INSTRUMENT PANEL 331 NOTE: Automatic Temperature Controls (ATC) will auto- matically adjust the climate control settings to reduce or eliminate window fogging on the front windshield. When this occurs, recirculation will be unavailable. Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves.
Page 334 332 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions...
Page 335: Personalized Menu Bar
UNDERSTANDING YOUR INSTRUMENT PANEL 333 PERSONALIZED MENU BAR The new app shortcut, that was dragged down onto the main menu bar, will now be an active App/shortcut. The Uconnect features and services in the main menu bar are easily changed for your convenience. Simply follow NOTE: This feature is only available if the vehicle is in these steps: PARK.
Page 336 334 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 8.4 NAV If you see the icon on your touchscreen, you have the Uconnect 8.4 NAV system. If not, you have a Uconnect 8.4 system.
Page 337: Get Started
UNDERSTANDING YOUR INSTRUMENT PANEL 335 Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions.
Page 338: Basic Voice Commands
336 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session •...
Page 339: Media
UNDERSTANDING YOUR INSTRUMENT PANEL 337 TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say “Help.” The system will provide you with a list of commands.
Page 340: Phone
338 UNDERSTANDING YOUR INSTRUMENT PANEL • Change source to Bluetooth • Change source to AUX • Change source to USB • Play artist Beethoven; Play album Greatest Hits; Play song Moonlight Sonata; Play genre Classical TIP: Press the Browse button on the touchscreen to see all of the music on your AUX or USB device.
Page 341: Voice Text Reply
UNDERSTANDING YOUR INSTRUMENT PANEL 339 • Call John Smith • Dial 123-456-7890 and follow the system prompts • Redial (call previous outgoing phone number) • Call back (call previous incoming phone number) TIP: When providing a Voice Command, push the Phone button and say “Call,”...
Page 342 340 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without I’ll be late. Okay.
Page 343: Climate (8.4/8.4 Nav)
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Climate (8.4/8.4 NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) Push the VR button . After the beep, say one of the following commands: •...
Page 344: Navigation (8.4 /8.4 Nav)
• For the 8.4 Uconnect System, say: “Enter state.” • For the 8.4 NAV Uconnect System, say: “Find address 800 Chrysler Drive Auburn Hills, Michigan.” 2. Then follow the system prompts. TIP: To start a POI search, push the VR button .
Page 345: Uconnect Access (8.4/8.4 Nav)
UNDERSTANDING YOUR INSTRUMENT PANEL 343 Uconnect Access (8.4/8.4 NAV) 9-1-1 Call Security Alarm Notification WARNING! Remote Door Lock/Unlock ALWAYS obey traffic laws and pay attention to the Stolen Vehicle Assistance road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable Remote Vehicle Start** 1X(voice/data) or 3G(data) network connection.
Page 346: Register (8.4/8.4 Nav)
344 UNDERSTANDING YOUR INSTRUMENT PANEL Register (8.4/8.4 NAV) 2. Press the “Uconnect Care” button on the touchscreen. To unlock the full potential of Uconnect Access in your 3. A helpful Uconnect Care Agent will register your ve- vehicle, you first need to register with Uconnect Access. hicle and handle all of the details.
Page 347: Mobile App (8.4/8.4 Nav)
UNDERSTANDING YOUR INSTRUMENT PANEL 345 Mobile App (8.4/8.4 NAV) 4. Enter your login information for the selected app and press Link. You’re only a few steps away from using remote com- mands and playing your favorite music in your vehicle. 5.
Page 348 346 UNDERSTANDING YOUR INSTRUMENT PANEL 3. The Uconnect system will repeat your message and provide a variety of options to add to, delete, send or hear the message again. After the beep, tell Uconnect what you’d like to do. For instance, if you’re happy with your message, after the beep, say: “Send.”...
Page 349: Yelp (8.4/8.4 Nav)
UNDERSTANDING YOUR INSTRUMENT PANEL 347 TIP: TIP: Once you perform a search, you can reorganize the results by selecting either the Best Match, Rating or Dis- • Voice Texting is not compatible with iPhone, but if your tance tab on the top of the touchscreen display. vehicle is equipped with Siri Eyes Free, you can use your voice to send a text message.
Page 350: Siriusxm Travel Link (8.4/8.4 Nav)
348 UNDERSTANDING YOUR INSTRUMENT PANEL SiriusXM Travel Link (8.4/8.4 NAV) Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4 NAV system.
Page 351: Siri Eyes Free - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 349 Siri Eyes Free — If Equipped Siri lets you use your voice to send text messages, select media, place phone calls and much more. Siri uses your natural language to understand what you mean and will respond back to confirm your requests.
Page 352 350 UNDERSTANDING YOUR INSTRUMENT PANEL Getting Started Ensure Siri is enabled on your iPhone. Voice Recognition/Siri Buttons 1 — Phone Pick up Button 2 — Voice Recognition/Siri Eyes Free Button Siri Enable Screens 3 — Phone Hang Up Button 1. Pair your Siri enabled device to the vehicles sound system.
Page 353 UNDERSTANDING YOUR INSTRUMENT PANEL 351 2. After the double beep, begin speaking to Siri. Examples of Siri commands and questions: • Play Rolling Stones • Send text message to John • Read text message from Sarah • Take me to the nearest coffee shop NOTE: •...
Page 354: Do Not Disturb
352 UNDERSTANDING YOUR INSTRUMENT PANEL Do Not Disturb NOTE: • Reply with text message is not compatible with iPhones. With Do Not Disturb, you can disable notifications from incoming calls and texts, allowing you to keep your eyes • Auto reply with text message is only available on on the road and hands on the wheel.
Page 355: Additional Information
UNDERSTANDING YOUR INSTRUMENT PANEL 353 Additional Information © 2016 FCA US LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc.
Page 357 STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....359 PADDLE SHIFT MODE — IF EQUIPPED ..370 ▫ Normal Starting — Gasoline Engine ..359 ▫...
Page 358 356 STARTING AND OPERATING ▫ SafeHold ......378 TIRE SAFETY INFORMATION ....390 ▫...
Page 359 STARTING AND OPERATING 357 ▫ Carbon Monoxide Warnings ....423 TIRE CHAINS (TRACTION DEVICES) ..411 TIRE ROTATION RECOMMENDATIONS ..412 FLEXIBLE FUEL —...
Page 360 358 STARTING AND OPERATING ▫ Recreational Towing — Front-Wheel Drive (FWD) RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) ....431 Models ......431 ▫...
Page 361: Starting Procedures
STARTING AND OPERATING 359 STARTING PROCEDURES Normal Starting — Gasoline Engine Before starting your vehicle, adjust your seat, adjust both NOTE: Normal starting of either a cold or a warm engine inside and outside mirrors, and fasten your seat belts. is obtained without pumping or pressing the accelerator pedal.
Page 362: Extended Park Starting
360 STARTING AND OPERATING Extended Park Starting If Engine Fails To Start NOTE: Extended Park condition occurs when the vehicle WARNING! has not been started or driven for at least 30 days. • Never pour fuel or other flammable liquid into the 1.
Page 363: After Starting
STARTING AND OPERATING 361 With Tip Start ENGINE BLOCK HEATER — IF EQUIPPED If the engine fails to start after you have followed the The engine block heater warms the engine and permits Normal Starting , “Extreme Cold Weather and Extended quicker starts in cold weather.
Page 364: Automatic Transmission
362 STARTING AND OPERATING NOTE: AUTOMATIC TRANSMISSION • The engine block heater cord is a factory installed CAUTION! option. If your vehicle is not equipped, heater cords are available from your authorized MOPAR dealer. Damage to the transmission may occur if the following precautions are not observed: •...
Page 365: Ignition Park Interlock
STARTING AND OPERATING 363 NOTE: You must press and hold the brake pedal while WARNING! (Continued) shifting out of PARK. • Unintended movement of a vehicle could injure Ignition Park Interlock those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is This vehicle is equipped with an Ignition Park Interlock running.
Page 366: Nine-Speed Automatic Transmission
364 STARTING AND OPERATING Nine-Speed Automatic Transmission vehicle and driveline combinations utilize 9th gear only in very specific driving situations and conditions. The transmission is controlled using a rotary electronic gear selector located on the center console. The transmis- Only shift from DRIVE to PARK or REVERSE when the sion gear range (PRNDL/S) is displayed above the gear accelerator pedal is released and the vehicle is stopped.
Page 367: Gear Ranges
STARTING AND OPERATING 365 NOTE: In the event of a mismatch between the gear NOTE: After selecting any gear range, wait a moment to selector position and the actual transmission gear (for allow the selected gear to engage before accelerating. This example, driver selects PARK while driving), the position is especially important when the engine is cold.
Page 368 366 STARTING AND OPERATING WARNING! WARNING! (Continued) When the ignition is in the OFF position, the transmis- • Never use the PARK position as a substitute for the sion is locked in PARK, securing the vehicle against parking brake. Always apply the parking brake fully unwanted movement.
Page 369 STARTING AND OPERATING 367 NEUTRAL (N) CAUTION! Use this range when the vehicle is standing for prolonged • Before moving the transmission gear selector out of periods with the engine running. The engine may be PARK, you must start the engine and also press the started in this range.
Page 370 368 STARTING AND OPERATING DRIVE (D) If the transmission becomes extremely hot, the Transmis- sion Temperature Warning Light will illuminate, a warn- This range should be used for most city and highway ing message will appear in the instrument cluster, and the driving.
Page 371 STARTING AND OPERATING 369 LOW (L) — If Equipped 3. Push and hold the ignition switch until the engine turns OFF. Use this range for engine braking when descending very steep grades. In this range, the transmission will downshift 4. Wait approximately 30 seconds. for increased engine braking.
Page 372: Paddle Shift Mode - If Equipped
370 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until a temporary Paddle Shift mode. The transmission will the transmission fluid is warm (usually after 1 to 3 miles [2 revert back to normal operation after a period of time, to 5 km] of driving).
Page 373 STARTING AND OPERATING 371 • If Paddle Shift is engaged while in SPORT mode, the • Transmission shifting will be more noticeable when transmission will remain in the selected gear even when Paddle Shift mode is enabled. maximum engine speed is reached (except the transmis- •...
Page 374: All Wheel Drive (Awd) - If Equipped
372 STARTING AND OPERATING ALL WHEEL DRIVE (AWD) — IF EQUIPPED DRIVING ON SLIPPERY SURFACES This feature provides on-demand All-Wheel Drive (AWD). Acceleration The system is automatic with no driver inputs or addi- Rapid acceleration on snow covered, wet, or other slippery tional driving skills required.
Page 375: Traction
STARTING AND OPERATING 373 Traction Flowing/Rising Water When driving on wet or slushy roads, it is possible for a WARNING! wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or Do not drive on or across a road or path where water is complete loss of vehicle control and stopping ability.
Page 376: Power Steering
374 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Driving through standing water limits your vehicle’s • Driving through standing water may cause damage braking capabilities, which increases stopping dis- to your vehicle’s drivetrain components. Always in- tances. Therefore, after driving through standing spect your vehicle’s fluids (i.e., engine oil, transmis- water, drive slowly and lightly press on the brake sion, axle, etc.) for signs of contamination (i.e., fluid...
Page 377: Electric Park Brake (Epb)
STARTING AND OPERATING 375 ELECTRIC PARK BRAKE (EPB) WARNING! Your vehicle is equipped with an Electric Park Brake Continued operation with reduced assist could pose a System (EPB) that offers simple operation, and some safety risk to yourself and others. Service should be additional features that make the park brake more conve- obtained as soon as possible.
Page 378 376 STARTING AND OPERATING NOTE: The EPB fault lamp will illuminate if the EPB switch is held for longer than 20 seconds in the applied position or 90 seconds in the released position. The light will extinguish upon releasing the switch. If the Auto Park Brake feature is enabled, the parking brake will automatically engage whenever the transmission is placed into PARK.
Page 379 STARTING AND OPERATING 377 Once the park brake is fully disengaged, The BRAKE WARNING! (Continued) warning lamp in the instrument cluster and the LED • Never leave children alone in a vehicle, or with indicator on the switch will extinguish. access to an unlocked vehicle.
Page 380: Auto Park Brake
378 STARTING AND OPERATING Auto Park Brake CAUTION! The Electric Park Brake can be programmed to be applied If the Brake System Warning Light remains on with the automatically whenever the vehicle is at a standstill and parking brake released, a brake system malfunction is the automatic transmission is placed in PARK.
Page 381: Brake Service Mode
STARTING AND OPERATING 379 SafeHold can be temporarily bypassed by pressing the Service Mode has requirements that must be met in order Electric Park Brake Switch to the release position while the to be activated: driver door is open. Once manually bypassed, SafeHold •...
Page 382: Brake System
380 STARTING AND OPERATING BRAKE SYSTEM Your vehicle may also be equipped with Ready Alert Braking (RAB), Rain Brake Support (RBS), and Dynamic Your vehicle is equipped with dual hydraulic brake sys- Steering Torque (DST). tems. If either of the two hydraulic systems loses normal capability, the remaining system will still function.
Page 383: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 381 Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions. The system automatically prevents wheel by improperly installed or high output radio trans- lock, and enhances vehicle control during braking.
Page 384: Anti-Lock Brake Warning Light
382 STARTING AND OPERATING benefits of anti-lock brakes. If the “Anti-Lock Brake Warn- WARNING! (Continued) ing Light” does not come on when the ignition switch is • The capabilities of an ABS equipped vehicle must turned to the ON position, have the light repaired as soon never be exploited in a reckless or dangerous manner as possible.
Page 385: Hill Start Assist (Hsa)
STARTING AND OPERATING 383 The following conditions must be met in order for HSA to WARNING! activate: The Brake Assist System (BAS) cannot prevent the • The feature must be enabled. natural laws of physics from acting on the vehicle, nor •...
Page 386 384 STARTING AND OPERATING WARNING! WARNING! (Continued) brake pressure to hold both the vehicle and the There may be situations where the Hill Start Assist trailer on a hill when the brake pedal is released. In (HSA) will not activate and slight rolling may occur, order to avoid rolling down an incline while resum- such as on minor hills or with a loaded vehicle, or ing acceleration, manually activate the trailer brake...
Page 387: Traction Control System (Tcs)
STARTING AND OPERATING 385 • If disabling HSA using Uconnect Settings, refer to 8. Turn the ignition switch to the OFF position and then “Uconnect Settings” in “Understanding Your Instrument back to the ON position. If the sequence was completed Panel”...
Page 388: Electronic Stability Control (Esc)
386 STARTING AND OPERATING Electronic Stability Control (ESC) flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your This system enhances directional control and stability of speed and driving to the prevailing road conditions. the vehicle under various driving conditions.
Page 389 STARTING AND OPERATING 387 Partial Off WARNING! (Continued) The “Partial Off” mode is intended for times when a more steering system, suspension, braking system, tire spirited driving experience is desired. This mode may type and size or wheel size may adversely affect ESC modify TCS and ESC thresholds for activation, which performance.
Page 390 388 STARTING AND OPERATING The “ESC Activation/Malfunction Indicator Light” (lo- WARNING! cated in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The When in “Partial Off” mode, the TCS functionality of “ESC Activation/Malfunction Indicator Light”...
Page 391: Electronic Roll Mitigation (Erm)
STARTING AND OPERATING 389 The “ESC OFF Indicator Light” indicates the WARNING! (Continued) customer has elected to have the Electronic Sta- leaving the roadway or striking objects or other ve- bility Control (ESC) in a reduced mode. hicles. The capabilities of an ERM-equipped vehicle must never be exploited in a reckless or dangerous Electronic Roll Mitigation (ERM) manner which could jeopardize the user’s safety or the...
Page 392: Dynamic Steering Torque (Dst)
390 STARTING AND OPERATING Dynamic Steering Torque (DST) TIRE SAFETY INFORMATION Dynamic Steering Torque is a feature of the ESC and EPS Tire Markings modules that provides torque at the steering wheel for certain driving conditions in which the ESC module is detecting vehicle instability.
Page 393 STARTING AND OPERATING 391 NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
Page 394 392 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 395 STARTING AND OPERATING 393 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions –...
Page 396: Tire Identification Number (Tin)
394 STARTING AND OPERATING Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 397: Tire Terminology And Definitions
STARTING AND OPERATING 395 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 398: Tire Loading And Tire Pressure
396 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 399 STARTING AND OPERATING 397 Tire And Loading Information Placard WARNING! (Continued) • Improperly inflated tires are dangerous and can cause collisions. Under-inflation increases tire flex- ing and can result in over-heating and tire failure. Over-inflation reduces a tire’s ability to cushion shock.
Page 400 398 STARTING AND OPERATING Loading Steps For Determining Correct Load Limit— The vehicle maximum load on the tire must not exceed the (1) Locate the statement “The combined weight of load carrying capacity of the tire on your vehicle. You will occupants and cargo should never exceed XXX kg or not exceed the tire’s load carrying capacity if you adhere to XXX lbs.”...
Page 401 STARTING AND OPERATING 399 • For the following example, the combined weight of Metric Example For Load Limit occupants and cargo should never exceed 865 lbs For example, if “XXX” amount equals 635 kg, and there (392 kg). will be five 68 kg passengers in your vehicle, the amount of available cargo and luggage load capacity is 295 kg (635- 340 (5x68) = 295 kg) as shown in step 4.
Page 402 400 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 403: Tires - General Information
STARTING AND OPERATING 401 TIRES — GENERAL INFORMATION WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 404: Tire Inflation Pressures
402 STARTING AND OPERATING Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 405: Tire Pressures For High Speed Operation
STARTING AND OPERATING 403 Example: If garage temperature = 68°F (20°C) and the WARNING! (Continued) outside temperature = 32°F (0°C) then the cold tire inflation cause them to fail. You could have a serious collision. pressure should be increased by 3 psi (21 kPa), which Do not drive a vehicle loaded to the maximum capacity equals 1 psi (7 kPa) for every 12°F (7°C) for this outside at continuous speeds above 75 mph (120 km/h).
Page 406: Tire Types
404 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and conditions. Install Winter tires on your vehicle when am- additional information. bient temperatures are less than 40°F (5°C) or if roads are covered with ice or snow. For more information, contact an Damaged Run Flat tires, or Run Flat tires that have authorized dealer.
Page 407: Run Flat Tires - If Equipped
STARTING AND OPERATING 405 Snow Tires Run Flat Tires — If Equipped Some areas of the country require the use of snow tires Run Flat tires allow you the capability to drive 50 miles during the Winter. Snow tires can be identified by a (80 km) at 50 mph (80 km/h) after a rapid loss of inflation “mountain/snowflake”...
Page 408 406 STARTING AND OPERATING spare tire descriptions begin with the letter “T” or “S” CAUTION! preceding the size designation. Example: T145/80D18 103M. Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a T, S = Temporary Spare Tire compact or limited use temporary spare installed.
Page 409 STARTING AND OPERATING 407 Collapsible Spare Tire — If Equipped WARNING! The collapsible spare is for temporary emergency use only. Compact and Collapsible spares are for temporary emer- You can identify if your vehicle is equipped with a collaps- gency use only. With these spares, do not drive more ible spare by looking at the spare tire description on the than 50 mph (80 km/h).
Page 410: Tire Spinning
408 STARTING AND OPERATING Limited Use Spare — If Equipped Tire Spinning The limited use spare tire is for temporary emergency use When stuck in mud, sand, snow, or ice conditions, do not only. This tire is identified by a label located on the limited spin your vehicle’s wheels above 30 mph (48 km/h) or for use spare wheel.
Page 411: Life Of Tire
STARTING AND OPERATING 409 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure – Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 412: Replacement Tires
410 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little It is recommended you contact your authorized tire dealer exposure to light as possible. Protect tires from contact with or original equipment dealer with any questions you may oil, grease, and gasoline.
Page 413: Tire Chains (Traction Devices)
STARTING AND OPERATING 411 WARNING! (Continued) WARNING! • Failure to equip your vehicle with tires having ad- Using tires of different size and type (M+S, Snow) equate speed capability can result in sudden tire between front and rear axles can cause unpredictable failure and loss of vehicle control.
Page 414: Tire Rotation Recommendations
412 STARTING AND OPERATING The suggested rotation method is the “forward cross” CAUTION! (Continued) shown in the following diagram. This rotation pattern does • Observe the traction device manufacturer’s instruc- not apply to some directional tires that must not be tions on the method of installation, operating speed, reversed.
Page 415: Treadwear
STARTING AND OPERATING 413 All passenger vehicle tires must conform to Federal safety WARNING! requirements in addition to these grades. The traction grade assigned to this tire is based on Treadwear straight-ahead braking traction tests, and does not The Treadwear grade is a comparative rating, based on the include acceleration, cornering, hydroplaning, or peak wear rate of the tire when tested under controlled condi- traction characteristics.
Page 416: Tire Pressure Monitor System (Tpms)
414 STARTING AND OPERATING also increase as the vehicle is driven. This is normal and WARNING! there should be no adjustment for this increased pressure. The temperature grade for this tire is established for a The TPMS will warn the driver of a low tire pressure if the tire that is properly inflated and not overloaded.
Page 417 STARTING AND OPERATING 415 may need to be driven for up to 20 minutes above 15 mph CAUTION! (24 km/h) in order for the TPMS to receive this informa- • The TPMS has been optimized for the original tion. equipment tires and wheels. TPMS pressures and For example, your vehicle may have a recommended cold warning have been established for the tire size (parked for more than three hours) placard pressure of 33...
Page 418: Premium System - If Equipped
416 STARTING AND OPERATING NOTE: Premium System — If Equipped • The TPMS is not intended to replace normal tire care and The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to maintenance, or to provide warning of a tire failure or monitor tire pressure levels.
Page 419 STARTING AND OPERATING 417 will display an Inflate to XX message and a graphic be driven for up to 20 minutes above 15 mph (24 km/h) in showing the pressure values of each tire with the low tire order for the TPMS to receive this information. pressure values in a different color.
Page 420 418 STARTING AND OPERATING If the ignition is cycled, this sequence will repeat, provid- 2. If you install the compact spare tire in place of a road tire ing the system fault still exists. If the system fault no longer that has a pressure below the low-pressure warning exists, the “Tire Pressure Monitoring Telltale Light”...
Page 421: General Information
STARTING AND OPERATING 419 the instrument cluster will display a new pressure value To reactivate the TPMS, replace all four wheel and tire instead of dashes (- -), as long as no tire pressure is assemblies (road tires) with tires equipped with TPM below the low-pressure warning limit in any of the four sensors.
Page 422: Fuel Requirements
420 STARTING AND OPERATING FUEL REQUIREMENTS Reformulated Gasoline Many areas of the country require the use of cleaner burning These engines are designed to meet all gasoline referred to as “Reformulated Gasoline”. Reformu- lated gasoline contains oxygenates and are specifically emissions regulations and provide opti- blended to reduce vehicle emissions and improve air quality.
Page 423: E-85 Usage In Non-Flex Fuel Vehicles
STARTING AND OPERATING 421 • Poor cold start and cold drivability. Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol • Increased risk for fuel system component corrosion. are not the responsibility of the manufacturer and may void or not be covered under New Vehicle Limited War- MMT In Gasoline ranty.
Page 424: Materials Added To Fuel
422 STARTING AND OPERATING Materials Added To Fuel Fuel System Cautions Besides using unleaded gasoline with the proper octane CAUTION! rating, gasolines that contain detergents, corrosion, and stability additives are recommended. Using gasolines that Follow these guidelines to maintain your vehicle’s have these additives will help improve fuel economy, performance: reduce emissions, and maintain vehicle performance.
Page 425: Carbon Monoxide Warnings
STARTING AND OPERATING 423 NOTE: Intentional tampering with the emissions control FLEXIBLE FUEL — IF EQUIPPED system can result in civil penalties being assessed against E-85 General Information you. The information in this section is unique for Flexible Fuel Carbon Monoxide Warnings vehicles only.
Page 426: Fuel Requirements
424 STARTING AND OPERATING NOTE: WARNING! (Continued) • Use seasonally adjusted E-85 fuel (ASTM D5798). With materials lit or products that can cause spark in or near non-seasonally adjusted E-85 fuel, hard starting and the vehicle when removing the fuel filler tube cap (gas rough idle following start up may be experienced even if cap) or filling the tank.
Page 427: Starting
STARTING AND OPERATING 425 Starting CAUTION! The characteristics of E-85 fuel make it unsuitable for use Replacing fuel system components with non-ethanol when ambient temperatures fall below 0°F (-18°C). In the compatible components can damage your vehicle. range of 0°F (-18°C) to 32°F (0°C), an increase in the time it takes for your engine to start may be experienced, and a Maintenance deterioration in driveability (sags and/or hesitations) until...
Page 428 426 STARTING AND OPERATING Push To Open Fuel Filler Door 3. Remove the fuel filler cap (gas cap) and hang by tether 1— Tether Hook hook on fuel filler door.
Page 429 STARTING AND OPERATING 427 6. Tighten the gas cap about one-quarter turn until you hear one click. This is an indication that the cap is properly tightened. 7. To close the fuel filler door, push the center-rear edge of the fuel filler door and then release. The fuel door will close.
Page 430: Loose Fuel Filler Cap Message
428 STARTING AND OPERATING WARNING! CAUTION! (Continued) • A poorly fitting fuel filler cap may cause the MIL to • Never have any smoking materials lit in or near the turn on. vehicle when the gas cap is removed or the tank is •...
Page 431: Vehicle Loading
STARTING AND OPERATING 429 VEHICLE LOADING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front Certification Label and rear axles. The load must be distributed in the cargo As required by National Highway Traffic Safety Adminis- area so that the GAWR of each axle is not exceeded.
Page 432: Trailer Towing
430 STARTING AND OPERATING Curb Weight rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down The curb weight of a vehicle is defined as the total weight low and be sure that the weight is distributed equally. Stow of the vehicle with all fluids, including vehicle fuel, at full all loose items securely before driving.
Page 433 STARTING AND OPERATING 431 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Front-Wheel Drive (FWD) All-Wheel Drive (AWD) Towing Condition Wheel OFF the Ground Models Models Flat Tow NONE NOT ALLOWED NOT ALLOWED Dolly Tow Front NOT ALLOWED Rear NOT ALLOWED NOT ALLOWED...
Page 434 432 STARTING AND OPERATING 3. Apply the parking brake. CAUTION! (Continued) 4. Place the transmission in PARK. • Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- 5. Turn the engine OFF. age from improper towing is not covered under the 6.
Page 435 WHAT TO DO IN EMERGENCIES CONTENTS ▫ Jacking Instructions .....447 HAZARD WARNING FLASHERS ... .434 ▫...
Page 436: Hazard Warning Flashers
434 WHAT TO DO IN EMERGENCIES • In city traffic — while stopped, place the transmission in HAZARD WARNING FLASHERS NEUTRAL, but do not increase the engine idle speed. The Hazard Warning flasher switch is located in the switch bank below the radio screen. NOTE: There are steps that you can take to slow down an impending overheat condition: Push the switch to turn on the Hazard Warning...
Page 437: Wheel And Tire Torque Specifications
WHAT TO DO IN EMERGENCIES 435 Inspect the wheel mounting surface prior to mounting the CAUTION! tire and remove any corrosion or loose particles. Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle.
Page 438: Tire Service Kit - If Equipped
436 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each WARNING! nut/bolt has been tightened twice. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered.
Page 439: Tire Service Kit Storage
WHAT TO DO IN EMERGENCIES 437 Tire Service Kit Storage 3. Remove the fastener securing the Tire Service Kit. The Tire Service Kit is stowed under an access cover in the trunk. 1. Open the trunk. 2. Lift the access cover using the pull strap. Tire Service Kit Fastener Pull Strap...
Page 440: Tire Service Kit Components And Operation
438 WHAT TO DO IN EMERGENCIES 4. Remove Tire Service Kit. Tire Service Kit Components And Operation Tire Service Kit Tire Service Kit Components 1 — Sealant Bottle 2 — Deflation Button 3 — Pressure Gauge 4 — Power Button 5 —...
Page 441: Tire Service Kit Usage Precautions
WHAT TO DO IN EMERGENCIES 439 • When the Tire Service Kit sealant is in a liquid form, Tire Service Kit Usage Precautions clean water, and a damp cloth will remove the material • Replace the Tire Service Kit Sealant Bottle (1) and Sealant from the vehicle or tire and wheel components.
Page 442 440 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • A loose Tire Service Kit thrown forward in a collision • Do not attempt to seal a tire on the side of the vehicle or hard stop could endanger the occupants of the closest to traffic.
Page 443: Sealing A Tire With Tire Service Kit
WHAT TO DO IN EMERGENCIES 441 Sealing A Tire With Tire Service Kit (B) Setting Up To Use Tire Service Kit: (A) Whenever You Stop To Use Tire Service Kit: 1. Push in the Mode Select Knob (5) and turn to the Sealant Mode position.
Page 444 442 WHAT TO DO IN EMERGENCIES (C) Injecting Tire Service Kit Sealant Into The 3. The Sealant Bottle (1) may be empty due to previous Deflated Tire: use. Call for assistance. • Always start the engine before turning ON the Tire NOTE: If the Mode Select Knob (5) is on Air Mode and the Service Kit.
Page 445 WHAT TO DO IN EMERGENCIES 443 If the tire does not inflate to at least 26 psi (1.8 Bar) CAUTION! pressure within 15 minutes: • The metal end fitting from Power Plug (8) may get • The tire is too badly damaged. Do not attempt to drive hot after use, so it should be handled carefully.
Page 446 444 WHAT TO DO IN EMERGENCIES (E) After Driving: NOTE: If the tire becomes overinflated, push the Deflation Button to reduce the tire pressure to the recommended Pull over to a safe location. Refer to “Whenever You Stop to inflation pressure before continuing. Use Tire Service Kit”...
Page 447: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 445 (F) Sealant Bottle And Hose Replacement: JACKING AND TIRE CHANGING 1. Uncoil the Sealant Hose (6) (clear in color). WARNING! 2. Locate the round Sealant Bottle release button in the • Do not attempt to change a tire on the side of the recessed area under the sealant bottle.
Page 448: Jack Location/Spare Tire Stowage
446 WHAT TO DO IN EMERGENCIES Jack Location/Spare Tire Stowage 3. Remove the fastener securing the jack and spare tire. The jack, wheel chocks and spare tire are stowed under an access cover in the trunk. Follow these steps to access the jack, wheel chocks and spare tire.
Page 449: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 447 6. Chock both the front and rear of the wheel diagonally WARNING! opposite of the jacking position. For example, if changing the right front A loose tire or jack thrown forward in a collision or tire, chock the left rear wheel.
Page 450 448 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 451 WHAT TO DO IN EMERGENCIES 449 Jacking Locations Removing Jack Handle From Jack 1. Remove the jack, wheel bolt wrench and wheel chocks 2. Chock both the front and rear of the wheel diagonally from the spare wheel as an assembly. Remove the chocks opposite of the jacking position.
Page 452 450 WHAT TO DO IN EMERGENCIES 5. Place the jack underneath the notched lift area that is closest to the flat tire. Rear Body Flange Front Body Flange...
Page 453 WHAT TO DO IN EMERGENCIES 451 Front Body Flange Engaged Rear Body Flange Engaged 6. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange.
Page 454 452 WHAT TO DO IN EMERGENCIES Front Jacking Location Rear Jacking Location WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
Page 455 WHAT TO DO IN EMERGENCIES 453 NOTE: CAUTION! • For vehicles so equipped, do not attempt to install a Be sure to mount the spare tire with the valve stem center cap or wheel cover on the compact spare. facing outward. The vehicle could be damaged if the •...
Page 456: Road Tire Installation
454 WHAT TO DO IN EMERGENCIES each wheel bolt has been tightened twice. Refer to which are on each side of the valve stem. Install the “Torque Specifications” in this section for proper lug wheel bolts with the threaded end of the bolt toward the bolt torque.
Page 457 WHAT TO DO IN EMERGENCIES 455 4. Install the remaining wheel bolts and lightly tighten. 8. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel. WARNING! Vehicles Equipped Without Wheel Covers To avoid the risk of forcing the vehicle off the jack, do...
Page 458: Jump-Starting Procedures
456 WHAT TO DO IN EMERGENCIES 5. Lower the jack until it is free. Remove the wheel chocks. CAUTION! Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using Do not use a portable battery booster pack or any other the means provided.
Page 459: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 457 WARNING! WARNING! • Take care to avoid the radiator cooling fan whenever Do not allow vehicles to touch each other as this could the hood is raised. It can start anytime the ignition establish a ground connection and personal injury switch is ON.
Page 460 458 WHAT TO DO IN EMERGENCIES 3. Connect the negative (-) end of the jumper cable to the 2. Disconnect the opposite end of the negative (-) jumper negative (-) post of the booster battery. cable from the negative (-) post of the booster battery. 4.
Page 461: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 459 FREEING A STUCK VEHICLE WARNING! If your vehicle becomes stuck in mud, sand or snow, it can Fast spinning tires can be dangerous. Forces generated often be moved using a rocking motion. Turn the steering by excessive wheel speeds may cause damage, or even wheel right and left to clear the area around the front failure, of the axle and tires.
Page 462: Manual Park Release
460 WHAT TO DO IN EMERGENCIES Follow these steps to activate the Manual Park Release: CAUTION! (Continued) 1. Apply the parking brake. • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires.
Page 463 WHAT TO DO IN EMERGENCIES 461 2. Using a small screwdriver or similar tool, remove the Manual Park Release access cover, which is underneath the rubber storage bin liner in the center console pass- through. Manual Park Release Tether 4. Pull the tether to rotate the lever up and rearward, until it locks vertically in place.
Page 464 462 WHAT TO DO IN EMERGENCIES To reset the Manual Park Release: 1. Pull the tether upwards to unlock the lever. 2. Rotate the Manual Park Release lever forward and down to its original position. 3. Re-install the access cover and the rubber storage bin liner.
Page 465: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 463 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheel OFF the Ground FWD MODELS AWD MODELS Flat Tow NONE NOT ALLOWED NOT ALLOWED Wheel Lift Or Dolly Tow Front NOT ALLOWED...
Page 466 464 WHAT TO DO IN EMERGENCIES • This recovery tow feature should be used by a trained CAUTION! professional only. Recovery feature: • Use approved receptacle location to free the disabled • Is to be used by a professional ONLY. vehicle from its environment.
Page 467: Front-Wheel Drive (Fwd) Models
WHAT TO DO IN EMERGENCIES 465 If the key fob is unavailable, or the vehicle’s battery is CAUTION! discharged, refer to “Manual Park Release” in this section for instructions on shifting the transmission out of PARK Towing this vehicle in violation of the above require- for towing.
Page 468: Enhanced Accident Response System (Ears)
466 WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) CAUTION! (Continued) This vehicle is equipped with an Event Data Recorder • Towing this vehicle in violation of the above require- (EDR). The main purpose of an EDR is to record, in certain ments can cause severe transmission and/or power crash or near crash-like situations, such as an air bag transfer unit damage.
Page 469 MAINTAINING YOUR VEHICLE CONTENTS ▫ Air Conditioner Maintenance ....479 ENGINE COMPARTMENT — 2.4L ...469 ▫ Body Lubrication ..... .482 ENGINE COMPARTMENT —...
Page 470 468 MAINTAINING YOUR VEHICLE ▫ Stop/Rear Turn Signal Lamp....518 REPLACEMENT BULBS ....508 ▫...
Page 471: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE 469 ENGINE COMPARTMENT — 2.4L 1 — Air Cleaner Filter 5 — Power Distribution Center (Fuses) 2 — Engine Coolant Pressure Cap 6 — Battery 3 — Oil Fill Cap 7 — Washer Fluid Reservoir 4 — Brake Fluid Reservoir 8 —...
Page 472: Engine Compartment - 3.6L
470 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.6L 1 — Engine Coolant Reservoir 5 — Washer Fluid Reservoir 2 — Engine Oil Filter Access Cover 6 — Battery 3 — Brake Fluid Reservoir 7 — Engine Oil Fill 4 — Power Distribution Center (Fuses) 8 —...
Page 473: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 471 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! (Continued) Your vehicle is equipped with a sophisticated Onboard • If the MIL is flashing while the engine is running, Diagnostic system called OBD II. This system monitors the severe catalytic converter damage and power loss performance of the emissions, engine, and automatic trans- will soon occur.
Page 474: Loose Fuel Filler Cap Message
472 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE WARNING! (Continued) PROGRAMS vehicle control could occur that may result in an In some localities, it may be a legal requirement to pass an accident involving serious injury or death. inspection of your vehicle’s emissions control system. •...
Page 475: Replacement Parts
MAINTAINING YOUR VEHICLE 473 2. As soon as you cycle the ignition to the ON mode, you Regardless of whether your vehicle’s OBD II system is will see the “Malfunction Indicator Light (MIL)” symbol ready or not, if the MIL is illuminated during normal come on as part of a normal bulb check.
Page 476: Maintenance Procedures
474 MAINTAINING YOUR VEHICLE WARNING! CAUTION! (Continued) have potential malfunctions examined by an autho- You can be badly injured working on or around a rized dealer or qualified repair center. motor vehicle. Only do service work for which you • Your vehicle has been built with improved fluids have the knowledge and the proper equipment.
Page 477 MAINTAINING YOUR VEHICLE 475 There are three possible dipstick types, NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 • Crosshatched zone. hours of engine run time, whichever comes first. The 350 •...
Page 478 476 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 3.6L Engine CAUTION! MOPAR SAE 5W-20 engine oil approved to FCA Material Do not use chemical flushes in your engine oil as the Standard MS-6395 such as Pennzoil, Shell Helix or equiva- chemicals can damage your engine.
Page 479: Engine Oil Filter
MAINTAINING YOUR VEHICLE 477 Synthetic engine oils which do not have both the engine oil high quality filters should be used to assure most efficient certification mark and the correct SAE viscosity grade service. MOPAR engine oil filters are high quality oil filters number should not be used.
Page 480: Maintenance-Free Battery
478 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Selection WARNING! (Continued) The quality of replacement engine air cleaner filters varies • Battery gas is flammable and explosive. Keep flame considerably. Only high quality filters should be used to or sparks away from the battery. Do not use a booster assure most efficient service.
Page 481: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 479 Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner should Do not use chemical flushes in your air conditioning be checked and serviced by an authorized dealer at the system as the chemicals can damage your air condition- start of each warm season.
Page 482 480 MAINTAINING YOUR VEHICLE Cabin Air Filter 2. Pull the console closeout cover rearward to disengage the front retaining tab and remove the cover. WARNING! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the ACC or ON/ RUN mode.
Page 483 MAINTAINING YOUR VEHICLE 481 3. Carefully remove the three push pins holding the hush 4. Remove the filter door by pushing down the tab on the panel and remove the part. top bottom of the door and lift the tab at the top of the door to release the cover then rotate remove the door out and lift up.
Page 484: Body Lubrication
482 MAINTAINING YOUR VEHICLE 5. Remove the cabin air filter by pulling it straight out of 7. Install the passenger side hush panel under the dash the housing. Take note of the air filter position flow panel and console closeout. direction indicators.
Page 485: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 483 Windshield Wiper Blades When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean Clean the rubber edges of the wiper blades and the the wiper blades, this will help blade performance. windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner.
Page 486 484 MAINTAINING YOUR VEHICLE loose connections could permit exhaust fumes to seep into CAUTION! the passenger compartment. In addition, have the exhaust • The catalytic converter requires the use of unleaded system inspected each time the vehicle is raised for lubri- cation or oil change.
Page 487: Cooling System
MAINTAINING YOUR VEHICLE 485 In unusual situations involving grossly malfunctioning WARNING! (Continued) engine operation, a scorching odor may suggest severe and open the hood until the radiator has had time to cool. abnormal catalyst overheating. If this occurs, stop the Never try to open a cooling system pressure cap when vehicle, turn off the engine and allow it to cool.
Page 488 486 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill CAUTION! (Continued) NOTE: Some vehicles require special tools to add coolant Additive Technology (OAT) engine coolant is differ- properly. Failure to fill these systems properly could lead to ent and should not be mixed with Hybrid Organic severe internal engine damage.
Page 489 MAINTAINING YOUR VEHICLE 487 • Use only high purity water such as distilled or deionized Adding Coolant water when mixing the water/engine coolant (anti- Your vehicle has been built with an improved engine freeze) solution. The use of lower quality water will coolant (OAT coolant conforming to MS.90032) that allows reduce the amount of corrosion protection in the engine extended maintenance intervals.
Page 490 488 MAINTAINING YOUR VEHICLE Cooling System Pressure Cap your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant The cap must be fully tightened to prevent loss of engine in open containers or allow it to remain in puddles on the coolant (antifreeze), and to ensure that engine coolant ground.
Page 491: Brake System
MAINTAINING YOUR VEHICLE 489 • Make sure that the coolant expansion bottle overflow Points To Remember hoses are not kinked or obstructed. NOTE: When the vehicle is stopped after a few miles/ • Keep the front of the radiator clean. If your vehicle is kilometers of operation, you may observe vapor coming equipped with air conditioning, keep the front of the from the front of the engine compartment.
Page 492 490 MAINTAINING YOUR VEHICLE Brake Master Cylinder WARNING! (Continued) The fluid in the master cylinder should be checked when vehicle is also identified on the original factory performing under hood services or immediately if the installed hydraulic master cylinder reservoir. “Brake Warning Light”...
Page 493: Automatic Transmission
MAINTAINING YOUR VEHICLE 491 Automatic Transmission Special Additives The manufacturer strongly recommends against using any Selection Of Lubricant special additives in the transmission. Automatic Transmis- It is important to use the proper transmission fluid to sion Fluid (ATF) is an engineered product and its perfor- ensure optimum transmission performance and life.
Page 494: Appearance Care And Protection From Corrosion
492 MAINTAINING YOUR VEHICLE level checked. Operating the vehicle with an improper fluid corrosive to the metal in your vehicle. Outside parking, level can cause severe transmission damage. which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or CAUTION! cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protec-...
Page 495 MAINTAINING YOUR VEHICLE 493 Washing Special Care • Wash your vehicle regularly. Always wash your vehicle • If you drive on salted or dusty roads, or if you drive near in the shade using MOPAR Car Wash, or a mild car wash the ocean, hose off the undercarriage at least once a soap, and rinse the panels completely with clear water.
Page 496 494 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care CAUTION! (Continued) All wheels and wheel trim, especially aluminum and covered by the New Vehicle Limited Warranty. Only chrome plated wheels, should be cleaned regularly using car wash soap, MOPAR Wheel Cleaner or equivalent is mild (neutral Ph) soap and water to maintain their luster recommended.
Page 497 MAINTAINING YOUR VEHICLE 495 • For tough stains, apply MOPAR Total Clean, or a mild NOTE: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel soap solution to a clean, damp cloth and remove stain. cleaner, drive your vehicle for a few minutes before doing Use a fresh, damp towel to remove soap residue.
Page 498 496 MAINTAINING YOUR VEHICLE ammonia-based cleaners to clean your leather upholstery. Cleaning Headlights Application of a leather conditioner is not required to Your vehicle is equipped with plastic headlights and fog maintain the original condition. lights that are lighter and less susceptible to stone breakage than glass headlights.
Page 499 MAINTAINING YOUR VEHICLE 497 When cleaning the rear view mirror, spray cleaner on the Replace the belts if they appear frayed or worn or if the towel or cloth that you are using. Do not spray cleaner buckles do not work properly. directly on the mirror.
Page 500: Fuses
498 MAINTAINING YOUR VEHICLE FUSES Power Distribution Center (Fuses) The Power Distribution Center is located in the engine WARNING! compartment near the battery. This center contains car- tridge fuses, mini-fuses, micro-fuses, circuit breakers and • When replacing a blown fuse, always use an appropri- relays.
Page 501 MAINTAINING YOUR VEHICLE 499 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not Used – 25 Amp Clear Engine Control Module (ECM)/ Fuel Inj. – – Not Used – 20 Amp Yellow Power Transfer Unit (PTU) – If Equipped –...
Page 502 500 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Blade Fuse Description – 10 Amp Red A/C Compressor Clutch – – Not Used – 5 Amp Tan Radiator Fan Enable – 70 Amp Tan Body Controller Module (BCM) – Feed 2 – 50 Amp Red Voltage Stability Module (VSM) #2 –...
Page 503 MAINTAINING YOUR VEHICLE 501 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not Used – – Not Used 50 Amp Red – Radiator Fan PWM Controller – – Not Used 40 Amp Green – HVAC Blower Motor –...
Page 504 502 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Blade Fuse Description 30 Amp Pink – Power Inverter (115V A/C) – If Equipped 30 Amp Pink – Windshield Wiper Smart Motor (WWSM) – – Not Used – – Not Used 30 Amp Pink –...
Page 505 MAINTAINING YOUR VEHICLE 503 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – 20 Amp Yellow Front Heated Seats – If Equipped – 20 Amp Yellow Heated Steering Wheel – If Equipped – 10 Amp Red In Vehicle Temperature Sensor/ Humidity Sensor/Driver Assist System Module (DASM)/Park Assist (PAM) –...
Page 506 504 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Blade Fuse Description – 20 Amp Yellow HID Headlamp Right – If Equipped with Engine Stop/Start Option – 10 Amp Red Heated Mirrors – If Equipped – – Not Used 30 Amp Pink –...
Page 507 MAINTAINING YOUR VEHICLE 505 Cavity Cartridge Fuse Blade Fuse Description – 20 Amp Yellow Horns – If Equipped With Engine Stop/Start Option F87A – 20 Amp Yellow HID Headlamp Left – If Equipped Engine Stop/Start Option – 10 Amp Red Collision Mitigation Module (CMM)/ Electrochromatic Mirror/Haptic Lane Feedback Module (Half)/Humidity...
Page 508: Interior Fuses
506 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Blade Fuse Description – 10 Amp Red Occupant Restraint Controller (ORC) (Airbag) – 25 Amp Clear Audio Amplifier – If Equipped – – Not Used F100 – – Not Used Interior Fuses The interior fuse panel is located in the passenger compart- ment on the left side dash panel under the instrument panel.
Page 509: Vehicle Storage
MAINTAINING YOUR VEHICLE 507 Cavity Blade Fuse Description 7.5 Amp Brown UCI Port (USB & AUX) 5 Amp Tan Trunk Lamp 5 Amp Tan Fog Lamp Front Left 5 Amp Tan Fog Lamp Front Right 10 Amp Red Low Beam Right VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery.
Page 510: Replacement Bulbs
508 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS Interior Bulbs Bulb Number Front Courtesy/Reading Lamp 578/W5W Center Courtesy/Reading Lamp 578/W5W Visor Vanity Lamp A6220 Glove Compartment Lamp A6220 Shift Indicator Lamp IKLE14140 Rear Compartment (Trunk) Lamp NOTE: For lighted switches, see your authorized dealer for replacement.
Page 511 MAINTAINING YOUR VEHICLE 509 Exterior Bulbs Bulb Number High Intensity Discharge Headlamp HID Bulb – D3S HID Bulb Bi-Halogen Headlamp 9005HL+ Daytime Running Lamp HID HDLP– LED Hal HDLP– Reduced Voltage LB 9005HL+ Front Turn Signal Lamp PWY24W SV Side Marker Lamp Front Park Lamp Hal HDLP –...
Page 512: Bulb Replacement
510 MAINTAINING YOUR VEHICLE BULB REPLACEMENT WARNING! NOTE: Lens fogging can occur under certain atmospheric A transient high voltage occurs at the bulb sockets of conditions. This will usually clear as atmospheric condi- HID headlamps when the headlamp switch is turned tions change to allow the condensation to change back into ON.
Page 513 MAINTAINING YOUR VEHICLE 511 2. Reach behind the headlamp housing to access the 4. Firmly grasp the headlamp bulb socket assembly and headlamp bulb cap. rotate counterclockwise to remove from the housing. 3. Firmly grasp the headlamp bulb cap and rotate it counterclockwise to unlock it.
Page 514: Front Turn Signal Lamp
512 MAINTAINING YOUR VEHICLE 5. Disconnect the bulb from the electrical connector and 7. Install the headlamp bulb cap in the headlamp housing then connect the replacement bulb. and rotate clockwise to lock it in place. 8. Lock headlamp access door in wheel liner. Front Turn Signal Lamp 1.
Page 515 MAINTAINING YOUR VEHICLE 513 3. Remove the brace by removing the four fasteners and 6. Install the front turn signal lamp socket assembly into loosening the 5th inboard fastener. the housing, and rotate the front turn signal lamp socket clockwise to lock it in place. 4.
Page 516: Front Side Marker Lamps
514 MAINTAINING YOUR VEHICLE Front Side Marker Lamps 1. Remove the three fasteners from the inner wheel liner and carefully peel back liner for access. Front Side Marker Lamp Bulb Removal 3. Remove bulb from the front side marker lamp socket and replace with a new bulb.
Page 517: Front Fog Lamp
MAINTAINING YOUR VEHICLE 515 Front Fog Lamp 1. Remove the three fasteners from the lower closeout, and peel down the lower closeout. Front Fog Lamp Socket 4. Pull the bulb out of the socket and insert the replace- ment bulb. Lower Closeout CAUTION! 2.
Page 518: Backup Lamps (Passenger Side)
516 MAINTAINING YOUR VEHICLE 5. Install the front fog lamp socket assembly into the into 5. Gently pull back the inner deck panel behind the trunk the front fog lamp housing, and rotate the connector lid lamp housing to expose the backup lamp socket. clockwise to lock it in place.
Page 519: Backup Lamps (Driver Side)
MAINTAINING YOUR VEHICLE 517 6. Rotate the backup lamp socket counter clockwise 1/4 10. Reposition the inner deck panel and secure with a push turn to remove the backup lamp socket from the trunk pin if removed. lid lamp housing. 11.
Page 520: Stop/Rear Turn Signal Lamp
518 MAINTAINING YOUR VEHICLE 9. Reposition the inner deck panel and secure with a push pin if removed. 10. Install the access cover. Stop/Rear Turn Signal Lamp 1. Open the trunk lid. 2. Remove the tail lamp housing beauty cover by grasping the top edge and pulling rearward to expose the tail lamp housing bolts.
Page 521: License Plate Lamp
MAINTAINING YOUR VEHICLE 519 3. Remove the tail lamp housing bolts. 6. Remove the bulb from the socket and install the replace- ment bulb. 7. Install the bulb socket into the tail lamp housing and rotate the bulb socket ¼ turn clockwise to lock it in place.
Page 522: Fluid Capacities
520 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 2.4L and 3.6L Engines 15.8 Gallons 60 Liters Engine Oil With Filter 2.4 Liter Engine (SAE 0W-20, API 5.5 Quarts 5.2 Liters Certified) 3.6 Liter Engine (SAE 5W-20, API 6 Quarts 5.6 Liters Certified) Cooling System*...
Page 523: Fluids, Lubricants, And Genuine Parts
MAINTAINING YOUR VEHICLE 521 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Tech- nology) or equivalent meeting the requirements of FCA Material Standard MS.90032.
Page 524 522 MAINTAINING YOUR VEHICLE CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) en- gine coolant (antifreeze), may result in engine dam- age and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is differ- ent and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (anti- freeze) or any “globally compatible”...
Page 525: Chassis
MAINTAINING YOUR VEHICLE 523 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only MOPAR ZF 8&9 Speed ATF Automatic Transmis- sion Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Brake Master Cylinder We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703 should be used.
Page 527 MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart .....527 MAINTENANCE SCHEDULE ....526...
Page 528 526 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE NOTE: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), twelve months or 350 hours Your vehicle is equipped with an automatic oil change of engine run time, whichever comes first. The 350 hours of indicator system.
Page 529 MAINTENANCE SCHEDULES 527 Maintenance Chart Required Maintenance Intervals Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.
Page 530 528 MAINTENANCE SCHEDULES Mileage: Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Inspect front accessory drive belt, tensioner, idler pul- ley, and replace if necessary Additional Maintenance Replace engine air cleaner filter.
Page 531 MAINTENANCE SCHEDULES 529 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 533 IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......532 Speech Impaired (TDD/TTY) .
Page 534: Suggestions For Obtaining Service For Your Vehicle
532 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 535: Fca Us Llc Customer Center
Outside Mexico City: 1-800-505-1300 • Vehicle delivery date and mileage Puerto Rico And U.S. Virgin Islands FCA US LLC Customer Center Customer Service Chrysler International Services LLC P.O. Box 21–8004 P.O. Box 191857 Auburn Hills, MI 48321–8004 San Juan 00919-1857 Phone: (800) 247-9753 Tel.: (787) 782-5757...
Page 536: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
534 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech questions about the service contract, call the manufactur- er’s Service Contract National Customer Hotline at 1-800- Impaired (TDD/TTY) 521-9922 (Canadian residents, call (800) 465-2001 English / To assist customers who have hearing difficulties, the (800) 387-9983 French).
Page 537: Warranty Information
IF YOU NEED CONSUMER ASSISTANCE 535 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should imme- nents contain, or emit, chemicals known to the State of diately inform the National Highway Traffic Safety Admin-...
Page 538: Publication Order Forms
536 IF YOU NEED CONSUMER ASSISTANCE defect to the Canadian government should contact Trans- Diagnostic Procedure Manuals port Canada, Motor Vehicle Defect Investigations and Diagnostic Procedure Manuals are filled with diagrams, Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/ charts and detailed illustrations. These practical manuals roadsafety/ make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and fea-...
Page 539 INDEX...
Page 540 538 INDEX About Your Brakes ......380 Air Conditioner Maintenance ....479 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 541 INDEX 539 Automatic Headlights ..... . .128 Brake Control System, Electronic....380 Automatic High Beams .
Page 542 540 INDEX Chart, Tire Sizing......392 Console, Overhead ......217 Check Engine Light (Malfunction Indicator Light).
Page 543 INDEX 541 Defroster, Rear Window ..... .247 Driving Defroster, Windshield ......88 Through Flowing, Rising, Or Shallow Diagnostic System, Onboard .
Page 544 542 INDEX Emission Control System Maintenance... .472 Exhaust Gas Caution .....87, 423 Engine .
Page 545 INDEX 543 Fluid Leaks .......90 Fuel, Flexible......423 Fluid Level Checks Fuses .
Page 546 544 INDEX Switch ....... .127 Interior Appearance Care .....495 Time Delay .
Page 547 INDEX 545 Keyless Enter-N-Go ......30 Automatic Headlights .....128 Enter The Trunk .
Page 548 546 INDEX Low Fuel ......270 Lug Nuts ....... .435 Malfunction Indicator (Check Engine) .
Page 549 INDEX 547 Multi-Function Control Lever ....131 Operating Precautions ..... . .471 Operator Manual (Owner’s Manual) .
Page 550 548 INDEX Forward .......113 Reminder, Lights On ......130 Rearward .
Page 551 INDEX 549 Replacement Parts ......473 Seat Belt Maintenance ..... . .497 Replacement Tires .
Page 552 550 INDEX Ventilated ......118 Specifications Security Alarm ......259 Fuel (Gasoline) .
Page 553 INDEX 551 Stuck, Freeing ......459 Life Of Tires ......409 Sunglasses Storage.
Page 554 552 INDEX Automatic ......362 Untwisting Procedure, Seat Belt ....44 Autostick .
Page 555 INDEX 553 Power ....... . .33 Power Windows ......33 Rear Passenger Window Controls .
Page 556 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

Chrysler 200 2017 Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Chrysler 200 2017

Summary of Contents for Chrysler 200 2017