User’s Manual E656 E556 E506 E436 E326 Please find your model name in the label on the backside of monitor.
Care Of The Screen ..............English-37 Mobile Telephone Warning ............English-37 End Of Life Directives.............. English-37 Manufacturer’s Recycling and Energy Information ......English-38 Disposing of your old NEC product ......... English-38 Energy Saving ................. English-38 Product Specification ................. English-39 RS-232C Port Specifications ........... English-45 Supporting HDMI CEC command ...........
Precautions And Reminders Do not place the TV in Do not open the TV Call a NEC certified confined spaces or in a cabinet. service personnel for any box when in use. Maintain internal service needed for ample ventilation for the your TV.
Important Safety Instructions Read before operating equipment Follow all warnings and instructions marked on this TV. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. Do not block any ventilation openings.
17. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. 18. An outdoor antenna should not be located near overhead power lines or any electrical circuits. 19. If an outside antenna is connected to the receiver, confirm that the antenna system is grounded to protect against voltage surges and built up static charges.
WARNING: To prevent the apread of fire, keep candles or other open flames away fram this product at all times. IMPORTANT INFORMATION If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as: •...
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
If the TV does not operate properly, unplug the LCD TV and call your authorized dealer or service center. Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by NEC could void the user’s warranty. Batteries installed warning CAUTION: Incorrect usage of batteries can result in leaks or bursting.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Install on the wall 11 7/8 inches 30 cm 4 inches 4 inches 10 cm 10 cm Leave at least this space around the set. 4 inches 10 cm 2.36 inches 6 cm For use only with UL Listed Wall Mount Bracket with minimum weight / load: Please refer to the Specification on page 40 and page 43 .
Installed with stand 11 7/8 inches 30 cm 4 inches 4 inches 10 cm 10 cm Leave at least this space around the set. 4 inches 10 cm Never install the TV set where air-circulation is blocked. Objects and ventilation holes Never push objects of any kind into the TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or an electric shock.
License Notice and Trademark Acknowledgement Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners. The terms HDMI and HDMI High- ®...
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 500 Park Boulevard, Suite 1100 Itasca, Illinois 60143 Tel.
FCC Information: Use the attached specified cables with the E656 / E556 / E506 / E436 / E326 color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance.
1.5 V AAA batteries (2) • Power cord (1) • D-sub cable (1) • User’s manual (1) E656 / E556 / E506 / E436 / E326 Wireless Remote Control Power Cord and AAA Batteries User’s Manual Video Signal Cable (Mini D-SUB 15 pin to User’s Manual...
The manufacturer’s warranty does not cover user abuse or improper installations. Attaching the Base E656 Stand Screw x 4 E656: M6 (30mm) E556 / E506 / E436 / E326 Stand Screw x 4 E556/E506: M6 (22mm) E436/E326: M4 (20mm) Place the TV face down on a soft and flat surface to prevent scratching and damage.
TV.(Please see page 40 and page 43 ) To attach a wall mount bracket to your TV: E656 VESA Hole Stand Screw Loosen the screws on the bottom of the base, and remove the base.
NOTE: Wall mounting solution is not included with the unit and is sold separately. Contact your NEC representative for details. It is necessary to provide screw of appropriate length (Wall mount bracket thickness + VESA Hole depth). Prohibit Portrait Condition Use CAUTION: Do not rotate the display from landscape to portrait.
Place The TV On A Solid Surface Ensure that the LCD TV is placed in a position to allow free flow of air. Do not cover the ventilation openings on the back cover. Do not place the TV near any open flames.
Battery Installation and Replacement The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: Open the battery cover of the remote control by pushing and pulling it in the direction of the arrow. 2. Insert two new “AAA” size batteries for the remote control.
Power On/Off Your New LCD TV Press the power button on the remote control or press the power button located on the side of the TV. The TV will power on. Power button Power Mode Status When in ON mode, the Monitor operates as follows if no external signal is input.
1-4. When the external device is connected to another terminal (HDMI, component video, composite video), the NO SIGNAL menu is displayed and 10 seconds later the Monitor switches to Auto Power save mode. 1-5. For example, In Auto Power save mode at HDMI-1 terminal, when the Monitor receives a signal from an external HDMI-1 device, it switches automatically to ON mode.
3-5. For example, In Auto Power save mode at HDMI-1 terminal, when the Monitor receives a signal from an external HDMI-1 device, it switches automatically to ON mode. 3-6. For example, In Auto Power save mode at HDMI-1 terminal, when the Monitor does not receive a signal from external HDMI-1 device, the monitor keeps Auto Power save mode.
Source Connection Guide E656 AC POWER ❶ ❷ ❸ ❼ ❻ ❺ ❹ RS-232C – Connect to your PC, and receive the control commands from the PC. 2. HDMI (HDMI-1, HDMI-2, HDMI-3) – Connect to your HDMI devices. HDMI-1 terminal can support ARC (Audio Return Channel) function.
E556 / E506 / E436 / E326 AC POWER ❶ ❷ ❸ ❼ ❻ ❺ ❹ RS-232C – Connect to your PC, and receive the control commands from the PC. 2. HDMI (HDMI-1, HDMI-2, HDMI-3) – Connect to your HDMI devices. HDMI-1 terminal can support ARC (Audio Return Channel) function.
Once your AV device is connected, press the Source button on the remote control to select the relevant source to view. (ex: Press COMP button to select “Component” if you have connected a source to the Component input.) PRE CH English-24...
Operating Instructions Using The Side Panel Controls Press to increase the volume. VOL + Press this button to shift Right in the OSD menu. Press to decrease the volume. VOL - Press this button to shift Left in the OSD menu. Press to change channels.
Using The Remote Control (Power) Press to turn On/Off (standby) the power. (NOTE: To completely turn off the power, unplug the power cord from the power outlet.) Press to choose ATSC/NTSC tuner source mode. Press to choose Composite source mode. PRE CH COMP Press to choose Component source...
Audio Press to activate the NTSC tuner Press to choose sound mode: sounds such as Stereo, SAP, Mono- Standard / Movie / Music / News / tone, and languages of the digital Custom. tuner. CH-List Wide Press to display the Channel List. Press to choose the display aspect ratio: Normal / Zoom / Wide / Cinema Press to activate the Closed Caption.
Timing Table Horizontal Vertical Nominal Pixel Resolution Nominal Freq. Sync Nominal Freq. Sync Clock (MHz) (kHz) Polarity (Hz) Polarity 640 × 480@60Hz ● 31.469 – 59.94 – 25.175 720 × 400@70Hz ● 31.469 – 70.087 28.322 800 × 600@60Hz ● 37.879 60.317 1024 ×...
Navigating The On-Screen Menu Press the Menu button to display and Exit button to close the main menu. Use the Navigation Ring to navigate, select, adjust or confirm an item on the OSD (On-Screen Display) menu. NOTE: Some features may only be available in a particular source mode. Video Menu [Dynamic Backlight] (DCR) Enhance the contrasts between...
Audio Menu 10. Menu Speech Enable speech function for OSD Audio Menu provides an audio menu and certain operations. adjustment for user to modify the 11. Reset Audio Settings audio setting. Reset Audio settings to factory HDMI 1 default settings. Audio Standard Sound Mode...
Setup Menu [Change Password] Change the 4-digit password. Setup Menu in TV mode is shown You will have to enter the new below. According to various password first, then enter again requirements in different source the new password to confirm. modes, certain features could be Make sure to keep your new hidden (disabled) on the menu.
[Phase] ARC is an audio link which can replace other cables between Eliminate flicker and distortion. the Monitor and the receiver or [Reset RGB Options] speaker system. HDMI-1 terminal Reset RGB options to factory can support ARC function. default settings. [Device List] 10.
USB Menu • Select to repeat images in the Repeat folder with Repeat None / Repeat You could browse image, music, or One / Repeat All options. video files from USB storage device. Repeat None After starting playing the files USB 2.0 selected in the menu, each file in the same folder is played once in...
To control while enjoying musics • Select to loop through a Set A or videos: certain part of music or video. • Select or press ►/p button to • Select to play music or video PLAY Random On play the file. in the folder randomly.
Data Format for USB Supported file FAT16/32, NTFS system Max. folder layer PHOTO mode Data format JPEG, JPG, JPE Max. number of 1200 photos Min. image 75 × 75 pixels resolution Max. image 1,024 × 768 pixels resolution (Progressive DCT) Max.
USB Demo Mode Play files in USB Demo Mode During demo mode: The Monitor could automatically play • The Power, Volume and Mute image, music, or video files from buttons on remote control are USB storage device with USB Demo functional.
Maintenance and Recycling Care Of The Screen Do not rub or strike the screen with anything hard as this may scratch, mar, or even damage the screen permanently. Unplug the power cord before cleaning the screen. Dust the TV by wiping the screen and the cabinet with a soft, clean cloth.
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.
Reorient or relocate the receiving display. Designs and specifications are subject to change without notice. This model may not be compatible with features and/or specifications that may be added in the future. Model Name E656 E556 DISPLAY Viewable 65” 55”...
Model Name E656 E556 WEIGHT & DIMENSION Dimensions w/ Stand and Base 57.40 34.42 13.78 48.79 29.51 10.04 × × × × D) (inch) × × Dimensions w/o Stand and Base 57.40 32.85 3.52 48.79 28.02 3.12 × × ×...
Model Name E656 E556 PACKAGE CONTENTS Monitor (1) Remote control (1) 1.5 V AAA batteries (2) Supplied Accessories Power cord (1) (3.0m) D-sub cable (1) (1.8m) User’s manual (1) All specifications, weights, and dimensions are subject to change without prior notice. Please access www.necdisplay.com for detailed specifications and dimensions for custom installations.
Model Name E506 E436 E326 DISPLAY Viewable 50” 43” 32” Resolution 1,920 1,080 × Color Over 16 million colors (depending on video card used) 31 ─ 83 KHz (Analog input) Horizontal: 15.625/15.734KHz, 31 - 83KHz (HDMI input) Frequency 60 Hz, 70 Hz (Analog input) Vertical: 24 Hz, 30 Hz, 50 Hz, 60 Hz, 70 Hz (HDMI input)
Model Name E506 E436 E326 Dimensions w/o Stand and 44.24 25.46 3.03 38.12 22.02 3.02 28.61 × 16.70 × 3.02 × × × × Base (W D) (inch) × × Weight w/ Stand and Base (lbs) 29.50 lbs 19.96 lbs 11.71 lbs Weight w/o Stand and Base 28.40 lbs...
Model Name E506 E436 E326 PACKAGE CONTENTS Monitor (1) Remote control (1) 1.5 V AAA batteries (2) Supplied Accessories Power cord (1) (3.0m) D-sub cable (1) (1.8m) User’s manual (1) All specifications, weights, and dimensions are subject to change without prior notice.
RS-232C Port Specifications PC control of the TV Attach an RS-232C cable cross-type (commercially available) to the supplied RS-232C for the connections. NOTE: This operation system should be used by a person who is accustomed to using computers. Communication procedure Send the control commands from the PC via the RS-232C connector.
Supporting HDMI CEC command HDMI CEC command Explanation name If HDMI CEC supporting devices are turned on, the monitor that connected the devices by HDMI cable is also One Touch Play turned on automatically then changed Input to HDMI. If the monitor is turned on when HDMI CEC devices are turned on, it changed input to HDMI.
Before Calling Service Please make these simple checks before calling service. These tips may save you time and money as charges for receiver installation and adjustments of customer controls are not covered under your warranty. Symptoms Items To Check And Actions To Follow “Ghost ”...
Glossary HDTV HDTV displays are technically defined as being capable of displaying a minimum of 720p or 1080i active scan lines. HDMI Inputs High-Definition Multimedia Interface Audio / Video Inputs are located on the receiver. These connectors are used for the input of audio and video signals. Designed to receive higher picture resolution and offer sound connection options.