Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 LNP-1604G-SFP Series 16-Port Industrial Gigabit PoE+ Unmanaged Ethernet Switches with 12*10/100/1000Tx (PSE: 30W/Port) + 4*100/1000 SFP Slots Version 1.0 User Manual...
Page 2
Trademark Information Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the registered trademarks of Wi-Fi Alliance.
Industrial Grade Unmanaged Ethernet Switches User Manual Version 1.0 (March 2017) This manual supports the following models: LNP-1604G-SFP LNP-1604G-SFP-T This document is the current official release manual. Please check our website (www.antaira.com) for any updated manual or contact us by e-mail (support@antaira.com).
LNP-1604G-SFP Series User Manual V1.0 1. Overview Antaira Technologies’ LNP-1604G-SFP industrial gigabit PoE+ unmanaged Ethernet switch series has twelve 10/100/1000TX RJ45 ports that support IEEE 802.3af/at PoE/PoE+ standards supplying up to 30 watts per port. The device also has four dual rate (100/1000) SFP slots for fiber connection.
LNP-1604G-SFP Series User Manual V1.0 2. Hardware Description 2.1 Physical Dimensions Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNP-1604G-SFP series: 16-port industrial Gigabit PoE+ unmanaged Ethernet switches with 12*10/100/1000Tx (PSE: 30W/Port) + 4*100/1000 SFP slots. (W x D x H) is 59mm x 99mm x 142mm Figure 2.1...
Figure 2.2 - Front Panel of the LNP-1604G-SFP Series 2.3 Top View Figure 2.3, below, shows the top panel of the LNP-1604G-SFP series switch that is equipped with one 6-pin removal terminal block connector for dual DC power inputs (48~55 VDC).
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 2.4 LED Indicators There are LED light indicators located on the front panel of the industrial Ethernet switch that display the power status and network status. Each LED indicator has a different color and has its own specific meaning, see below in Table 2.1.
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 2.5 Ethernet Ports RJ-45 Ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for 10/100/1000Base-Tx devices connections. Auto MDI/MDIX means that the switch can connect to another switch or workstation without changing the straight- through or crossover cabling.
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 The following figures show the cabling schematics for straight-through and crossover cables. Figure 2.4 Figure 2.5 Straight-Through Cables Schematic Crossover Cables Schematic The following figures show the 10,100, and 1000 Ethernet RJ‐45 pin outs.
Page 12
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 The small form-factor pluggable (SFP) is a compact optical transceiver used in optical communications for both telecommunication and data communication applications. To connect the transceiver and LC cable, please follow the steps below: First, insert the SFP transceiver module into the SFP slot as shown below in Figure 2.7.
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 2.7 Wiring the Power Inputs Please follow the below steps to insert the power wire. 1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 2.12.
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 3. Mounting Installation 3.1 DIN-Rail Mounting The DIN-Rail is pre-installed on the industrial Ethernet switch from the factory. If the DIN-Rail is not on the industrial Ethernet switch, please refer to Figure 3.1 to learn how to install the DIN-Rail on the switch.
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 3.2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3.4. 1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
If the power indicator LED does not turn on when the power cord is plugged in, the user may have a problem with the power cord. Check for loose power connections, power losses or surges at the power outlet. Please contact Antaira for technical support service, if the problem still cannot be resolved. ...
Antaira Technologies - Industrial Ethernet Switches LNP-1604G-SFP Series User Manual V1.0 7. Technical Specifications Table 7.1 has the technical specifications for Antaira Technologies’ LNP-1604G-SFP series: 16- port industrial gigabit PoE+ unmanaged Ethernet switch with 12*10/100/1000Tx (PSE: 30W/port), and 4*100/1000 SFP slots.
Page 20
Antaira Customer Service and Support (Antaira US Headquarter) + 844-268-2472 (Antaira Europe Office) + 48-22-862-88-81 (Antaira Asia Office) + 886-2-2218-9733 Please report any problems to Antaira: www.antaira.com support@antaira.com www.antaira.eu info@antaira.eu www.antaira.com.tw info@antaira.com.tw Any changes to this material will be announced on the Antaira website.
Need help?
Do you have a question about the LNP-1604G-SFP Series and is the answer not in the manual?
Questions and answers