Page 2
WIZnet’s Online Technical Support If you have something to ask about WIZnet products, write down your question on Q&A Board in WIZnet website (www.wiznet.co.kr). WIZnet will give an answer as soon as possible. Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
Page 3
COPYRIGHT NOTICE Copyright 2009 WIZnet Co., LTD. All Rights Reserved. Technical Support: support@wiznet.co.kr Sales & Distribution: sales@wiznet.co.kr For more information, visit our website at http://www.wiznet.co.kr Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
Configuration Tool ................14 2.2. Firmware Upload ..................24 Serial Configuration ..................26 Serial Command Format ..............26 4.1. WIZ105SR Configuration with Serial Command ........29 4.2. Hardware Configuration ................31 Frame Format ................31 5.1. Hardware Configuration Examples ............33 5.2.
Page 5
..............35 IGURE ERIAL ERMINAL ROGRAM CONFIGURATION 18. N ..............36 IGURE ETWORK ERMINAL ROGRAM CONFIGURATION 19. R ............36 IGURE ECEIVED ATA BY ETWORK ERMINAL ROGRAM 20. D ....................37 IGURE EVICE ERMINAL ROGRAM Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
Page 6
............. 31 ABLE ARDWARE ONFIGURATION EPLY RAME FORMAT 13. H ............... 31 ABLE ARDWARE ONFIGURATION OMMAND 14. H ............32 ABLE ARDWARE ONFIGURATION ARAMETER DESCRIPTIONS 15. H ............... 32 ABLE ARDWARE ONFIGURATION NTRANCE ESSAGE Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
WIZ105SR is a gateway module between serial device and Ethernet. It can transmit serial data to Ethernet and vice versa. With WIZ105SR, you can connect your serial device with Ethernet via WIZ105SR provides interface quite easier and shorten your development period to obtain more gains.
1.2. Products Contents (EVB model) WIZ105SR Module Test Board for WIZ105SR (Serial to Ethernet EVB) 12pin Cable (Connect WIZ105SR with Test Board) Serial Cable (Connect Serial Device with Test Board) LAN Cable (Connect WIZ105SR with Host) Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
WIZ105SR uses a high performance 8051 compatible microcontroller which feathers 62K in chip Flash, 16K in chip SRAM and 2K EEPROM. WIZ105SR feathers our fast hardwired TCP/IP stack chip W5100 and most of TCP/IP protocols such as TCP, UDP, IP, ARP, ICMP, IGMP, PPPoE and Ethernet MAC are all supported.
1.3.2. Connector Pin Assignment WIZ105SR provides an external connector to connect it with your application board. The pin assignment and definition of the connector are introduced in Figure.1 and the specification of each pin is described in Table 3. /RESET 3.3V...
WIZ105SR and the connection diagram is shown in Figure 3. Figure 2. WIZ105SR Configuration Environment Setting Diagram STEP 1: Connect the WIZ105SR module to the test board by using the 12pin cable. STEP 2: Connect the 5V DC power line to the power jack of the test board.
ⓓ IP Configuration Method: Select IP setting mode, you can select one of Static, DHCP, PPPoE mode. - Static: “Static” is option for setting WIZ105SR IP with static IP address. Firstly, select MAC address which you wanted to set as static IP in the ‘board list’. Then “Local IP, Subnet,...
Page 15
If module could not acquire network information from DHCP server, IP address, Gateway Address and Subnet mask will be initialized to 0.0.0.0. - PPPoE : WIZ105SR supports PPPoE for ADSL user. When you select PPPoE at the “IP Configuration Method”, PPPoE ID & Password box is enabled.
Page 16
ⓗ PPPoE ID/Password : If you select ‘PPPoE’ mode, input ID/Password which you received from ISP company. ⓘ Server IP/Port : When WIZ105SR is set as “Client mode” or Mixed mode”, server IP and port should be set. WIZ105SR attempts to connect this IP address.
Page 17
<TCP client mode Communication> Figure 5. TCP Client mode If WIZ105SR is set as TCP Client, it tries to establish connection to the server. To operate this mode, Local IP, Subnet, Gateway Address, Server IP, and Server port number should be set. If server IP had domain name, use DNS function.
Page 18
As like TCP Server mode, the Mixed mode is useful for the case that the monitoring center tries to connect to the serial device (in which WIZ105SR is used) to check device status. In addition to this, if any emergency occurs in the serial device, the module will change to Client mode to establish the connection to the server and deliver the emergency status of the device.
Page 19
⑤ To check configuration result, click ‘Search’ button. ⓟ Upload Firmware will be uploaded through network ☞ After uploading the firmware, 20~30 seconds are required for initialization. ⓠ Exit : Close the configuration tool program. Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
ⓡ Serial Serial Configuration value of selected module is displayed. In order to change the serial configuration of WIZ105SR, this menu can be used. ☞ By clicking the “Setting” button, changed value can be applied. Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
In order to close the connection, the ‘Close’ command should be given. This function can be used for more than two or more systems to connect to a WIZ105SR module. If one system holds the connection to the WIZ105SR, other systems can not connect to the module.
Page 22
You can designate how the serial data can be packed to send to the Ethernet. In default mode, WIZ105SR checks the serial buffer and sends any received data to Ethernet without any standard. Therefore, the data can be regarded as error data due to inconsistent data lenth.
This function is for module configuration not through network with Configuration tool but through serial communication. When you want to set via serial communication, check “enable”. Please detail about serial configuration refers to “4. Serial Configuration”. Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
① Select a module shown in “Board list”, and click “Upload” button. ☞ Before uploading through Ethernet, you should set the network information of WIZ105SR first by Configuration Tool program as shown above Fig 10. By using Ping test, you can check if network is correctly configured.
Figure 11. Open dialog box for uploading ☞ Do not upload any other files except for WIZ105SR application firmware file. ③ A dialogue box titled “Processing” will be displayed as below. Figure 12. Firmware uploading window ④ When uploading is complete, a message box with “Complete Uploading” will be displayed as shown in Figure 14.
4. Serial Configuration 4.1. Serial Command Format It is possible to configure WIZ105SR by using serial command. By inputting specified 3 characters you can enter into the configuration mode. The characters can be defined at the Configuration Tool. < Frame Format >...
Page 27
0~65535 Set Inactivity timer value MAC Address Get MAC Address 0 : Not Use, 1 : Use DNS Use or Not IP address DNS IP Check Domain Domain Check PPPoE ID PPPoE ID Check Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
Get the server IP address 0~65535 Get the server port number Get delimiter character in hex 0~255 Get delimiter size 0~65535 Get delimiter time 0~65535 Get Inactivity timer value Table 9. Serial Configuration Command Code Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
4.2. WIZ105SR Configuration with Serial Command Figure 14. Serial Configuration Enable Setting ① Check WIZ105SR Firmware Version. If Version is lower, download the latest firmware from download page of http://www.wiznet.co.kr ② At the default status, the serial configuration is disabled. So, click ‘enable’ check box of serial configuration and click ‘setting’...
Above process is shown in the serial console as below figure. WIZ105SR Ver. 03.06 > Config socket : ok > Listen : Ok <E><S><S192.168.11.3><S> WIZ105SR Ver. 03.06 > Config socket : ok > Listen : Ok Figure 15. Serial Configuration Console Display Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
STEP 3. Check ‘<S’ message is displayed. After displaying this message, CR(0x0D) & LF(0x0A) are displayed together. STEP 4. After completing the change, check if changed value is appropriated saved by using READ command. Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
6. Demonstration and Test In this chapter, we give an example that can be used to test the function of WIZ105SR. The testing environment is as follows. <Hardware> PC having RS-232 serial port WIZ105SR & WIZ105SR Test Board Ethernet cable (Direct or Crossover) to connect PC and WIZ105SR ...
Figure 16. Result Window after Running “Setting” STEP3. (Data Transmission) ① Run terminal emulator program (e.g. Hyper terminal) on Test PC. ② Set the baud rate as the same value of WIZ105SR Figure 17. Serial Terminal Program configuration Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
⑤ Make sure this data is shown on the Network Hyper terminal window. (Serial to Ethernet) Figure 19. Received Data by Network Terminal Program ⑥ As the same way, type some characters on the network Hyper terminal, and then make Hardwired Internet Connectivity Wizard (WIZnet, Inc.)
Client and TCP Server modes. If Server Mode is checked, Device Terminal will operate as server mode, and the WIZ105SR module will work as client mode. The PC where the Device Terminal is operating will work as a server, the IP address of the PC should be set as Server IP of the module.
WIZnet warrants our products and its parts against defects in materials and workmanship under normal use for period of standard ONE YEAR for the WIZ105SR Module, Evaluation Board and labor warranty after the date of original retail purchase. During this period, WIZnet will repair or replace a defective products or part free of charge.
The software CD is not provide anymore. For more software contents, please visit our website. 2013-06-19 v1.2.0 (www.wiznet.co.kr) Modified the table of Product contents in CH 1.2. Software CD is removed in the table of contents. Hardwired Internet Connectivity Wizard (WIZnet, Inc.)