Download Print this page

Aleko AC1400 User Manual

Sliding gate operator
Hide thumbs

Advertisement

Sliding Gate Operator
User's Manual
Model: AC1400

Advertisement

loading

  Related Manuals for Aleko AC1400

  Summary of Contents for Aleko AC1400

  • Page 1 Sliding Gate Operator User’s Manual Model: AC1400...
  • Page 2: Table Of Contents

    AC1400 SLIDING GATE OPERATOR OUTLINE 1. Important safety precautions………………………2 2. Main features ………………………………………2 3. Main technical parameters ………………………2 4. Necessary Tools ……………………………………3 5. Site Preparation ……………………………………3 6. Mechanical Installation ……………………………4 7. Electrical ……………………………………………7 8. Tuning and operation ……………………………10 9. Check ………………………………………………14 10.
  • Page 3: Important Safety Precautions

    This work should only be performed by a trained technician. Miswiring could cause personal injury or DEATH. To prevent the risk of electrocution, be sure to turn off all power to the AC1400 until installation is complete. The gate operator should be installed by a qualified technician; otherwise, serious personal injury or property damage may occur.
  • Page 4: Necessary Tools

    AC1400 in the electrical section. The AC1400 requires at least a 10A service. Make sure your electrician takes into account the voltage drop involved in running many feet of wire to your installation location.
  • Page 5 Fig.1 Installation and Adjustment The AC1400 Chain-driven Gate Operator operates by forcing a straight piece of chain through its chain box. This length of chain is extended between two chain brackets located at opposite ends of the gate. The entire configuration is shown in the diagram above.
  • Page 6 AC1400 SLIDING GATE OPERATOR Gate operator Socket head cap screw Chain box Operator base Anchor bolt Anchor Conduit Cable Concrete pad Fig.2 Chain Box Make sure the ends of the guide chain are out of the chain holes on both sides of the chain box.
  • Page 7 AC1400 SLIDING GATE OPERATOR Chain Brackets Use the appropriate bolts to attach the chain bracket to the frame of the gate. If the gate is of square frame style, use the square bolts shown. Gate Square frame Plain washer ( Φ 6) Square bolt Spring washer ( Φ...
  • Page 8: Electrical

    AC1400 SLIDING GATE OPERATOR Magnets for Limit Switch Install the magnet and magnetic limit switch as shown in Fig.7. The magnet and limit switch are used to control the position of the gate. When the magnet is installed, release the gear clutch and push the sliding gate manually to pre-determine the position.
  • Page 9 AC1400 SLIDING GATE OPERATOR Control board scheme Fig.7...
  • Page 10 AC1400 SLIDING GATE OPERATOR Wiring notes for control board 1.Fuse: 10A, Ø5x20 2. Power input: E (Earth), L (Live), N (Neutral) AC110V 3. Motor: U (com), V (Positive direction), W (Opposite direction), E (grounding) 4. Capacitor: 14uF 5. Alarm lamp: AC110V 6.
  • Page 11: Tuning And Operation

    AC1400 SLIDING GATE OPERATOR 15. Output power supply: +12V (DC +12V), COM (CO),DET (Loop detector), I.R. (Infrared N.C) Terminal X8, No.15 Terminal X8, No.15 Terminal AC24V AC24V X5,No.11 +12V +12V Infrared Control board Infrared Control board Infrared with DC input...
  • Page 12 AC1400 SLIDING GATE OPERATOR To erase all existing remote controls, press and hold ‘AN’ button about 14 sec until the beeper stops ringing. This indicates that all the remote controls have been erased completely. The remote control works in a single channel mode. It has four buttons. The function of button 1, button 2 and button3 are the same.
  • Page 13 AC1400 SLIDING GATE OPERATOR is complete, return DIP switch 1 to OFF position immediately. Thus the auto-close function has been canceled. Pedestrian mode: Pedestrian mode can be used to open gate about 0.3~1.5 meters for people pass through. *Set width of pedestrian mode: Please turn on the first and the second DIP switch (See Fig.7 No.18) to ON position.
  • Page 14 AC1400 SLIDING GATE OPERATOR is complete, return DIP switch 1 to OFF position immediately. Thus the width of pedestrian mode has been canceled, the auto-close function of pedestrian mode has been reserved. Note: the new auto-close time of pedestrian mode has been re-programmed in the device and replaced the original auto-close time of pedestrian mode that you have been set in Set auto-close function of pedestrian mode section.
  • Page 15: Check

    AC1400 SLIDING GATE OPERATOR Single-button/keypad(not supply): with each press of the button, the gate will close, stop, open or stop cycle. Auto-reverse function: After adjusting the opening force and closing force, the gate will reverse and go open if obstructed when closing, and will stop if jammed when opening.
  • Page 16: Trouble Shooting

    AC1400 SLIDING GATE OPERATOR 11. Trouble Shooting Table 4 Trouble Possible causes Solutions The wire connector terminal block Check wire connector terminal block. becomes loose. Motor only runs in one direction. Check limit switch wire connector terminal The limit switch wire connector terminal block.