Aleko AS1200NOR User Manual
Aleko AS1200NOR User Manual

Aleko AS1200NOR User Manual

Swing gate opener

Advertisement

Swing Gate Opener
User's Manual
Model:
AS1200NOR
★ Please read and follow all warnings, precautions and instructions before
installation and use.
★ Never connect the solar panel to the control board directly to charge the battery.
★ Periodic checks of the opener are required to ensure safe operation.
★ Save this manual.
www.Aleko.com
C030750
VER 24b

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AS1200NOR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aleko AS1200NOR

  • Page 1 Swing Gate Opener User’s Manual Model: AS1200NOR ★ Please read and follow all warnings, precautions and instructions before installation and use. ★ Never connect the solar panel to the control board directly to charge the battery. ★ Periodic checks of the opener are required to ensure safe operation.
  • Page 2: Table Of Contents

    Table of Contents Safety Installation Information .......................... 1 AS1200NOR Parts List ............................ 2 Optional Accessories Parts List........................3 Tools Needed ..............................3 Technical Specifications & Features ........................ 4 Installation Overview ............................5 Preparation for Installation ..........................6 Install the Gate Opener on the Gate ........................ 6 Mounting the Control Box ..........................
  • Page 3: Safety Installation Information

    use on any pedestrian gate. Pedestrians must be Safety Installation Information supplied with a separate pedestrian access. 1. READ and FOLLOW all instruction. For an installation utilizing non-contact sensors The gate opener is intended for use with Class I (safety sensors), see product manual on the vehicular swing gates.
  • Page 4: As1200Nor Parts List

    13. To AVOID damaging gas, power, or other underground utility lines, contact underground utility locating companies BEFORE digging. SAVE INSTRUCTION. 14. Do not permit children to play on or around the gate and keep all controls out of their reach. AS1200NOR Parts List...
  • Page 5: Optional Accessories Parts List

    Optional Accessories Parts List Back-up Battery Electric Lock Wired Push Button Wireless Push Button (LM125) (LM149) (LM147) (LM173) Back-up Battery Box Alarm Lamp Exit Wand Photocell Beam (LM130) (LM140) (LM157) System ( LM102) Solar Controller Supporting Frame for Solar Panel Bracket for Solar Panel (SCCONT) Solar Panel (LM115)
  • Page 6: Technical Specifications & Features

    Technical Specifications & Features Specifications Model: AS1200NOR Input: 110-120V~/60Hz Motor voltage: 24VDC Power: 80W for each actuator Current: Actuator speed: 16mm/s(5/8 in/s) Max. actuator travel: 385mm(15 1/8 in) Ambient Temperature: -22℃~ +55℃ (-4° F to 122° F) Protection class: IP44 Features: ·Soft start and soft stop...
  • Page 7: Installation Overview

    Installation Overview Pull-to-Open Gates Important: The second gate opener cable should be put into the PVC conduit (not provided) which is buried underground .This protects the cable from lawn mowers and string trimmers.
  • Page 8: Preparation For Installation

    Preparation for Installation There are two installation types for the gate opener, Pull-to-Open and Push-to-Open. In the Push-to-Open installation, gate opens out from the property. A Push-To-Open Bracket (PSO part) is required to be used for each gate. NOTE: Ensure the gate does not open into public areas. The gate opener is mounted to the gate and to the gate post.
  • Page 9 Push-to-Open Installation — Gate in Closed position (Moving-Rod is retracted) 1. Insert the M10 x 35 bolt through the center hole of the post bracket and post pivot bracket as shown. Place a ¢ 10 washer , ¢10 lock washer and M10 nut on the bottom of the bolt and hand tighten. 2.
  • Page 10 5. Make sure that there is a minimum clearance of 2.5cm between the gate and the opener and that the opener and the Post Pivot Bracket are not binding in both the gate-open and gate-closed positions. If there is not at least 2.5cm of clearance or if the opener and the Post Pivot Bracket are binding, rotate the Post Pivot Bracket and/or move the Post Bracket Assembly to obtain the minimum clearance and eliminate the binding.
  • Page 11 6. Sign the bolt-hole point on the gate bracket and gate. Do this by placing a punch or a sign in the middle of each bolt slot on the post bracket assemblies and the gate bracket. It allows slight adjustments to the post bracket.
  • Page 12: Mounting The Control Box

    12. Open the release hole plug on the top of the gate opener, insert the release key, and turn the key 90° counterclockwise. This restores normal operation. Mounting the Control Box Step 1 To install the control box use the deck screws (not provided). Even though the control box is waterproof designed, for safety reason and a longer service life, it is recommended to install the control box inside a secure surface and at least 100 cm (40 inches) above the...
  • Page 13: Connection Of The Power Supply

    Step 3 Insert the cable of the motor2 and alarm lamp cables into the control box through middle strain relief. Then repeat step 2. Step 4 Insert other cables into the control box through rightmost strain relief. Then repeat step 2. NOTE: Only motor cables (1.5m length) are provided.
  • Page 14 Motor connection for PUSH-TO-OPEN The motors’ power wires and limit wires connection by “Push to Open” is different from the connection by “Pull to Open”. So motor 1 and motor 2 wires should be connected to the control box as the instruction on the right.
  • Page 15 “MOTOR1+” terminal, the black wire into “MOTOR1-“, the blue wire into ULT1, the green wire into COM, and the yellow wire into DLT1 terminal. Actuator 2 (for PULL-TO-OPEN) Similar as the connection of Actuator 1, insert the stripped cable wires into the appropriate terminals on the opener terminals block.
  • Page 16: How To Program Or Erase The Remote

    Please note that the adapter board of the exit wand should be inserted into the main control board of the gate opener before using. The BLACK and the BLUE wire of the exit wand should be connected into the “LOOP” terminal, no matter the polarity.
  • Page 17: How To Use The Remote To Operate Your Gate Opener

    How to Use the Remote to Operate Your Gate Opener Each remote has four buttons; they are button A, B, C and D. You may use this remote to operate as many as 4 sets swing gate openers or 1 set sliding gate opener and 2 sets swing gate openers. 1.
  • Page 18 1. Check again for completed and correct assembly of your swing gate opener and gate. Plug the Power Cord into the nearest AC outlet. The Digital Display on the Control Board will flash with “- -”. The unit is in standby. 2.
  • Page 19 Without a properly installed safety reversal system, person (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing gate. *Too much force on gate will interfere with proper operation of safety reversal system. *NEVER increase force beyond minimum amount required to close gate. *NEVER use force adjustments to compensate for a binding or sticking gate.
  • Page 20: Indicate Illustration On The Digital Display When Gate Opener Is Running

    indicates “11”, the PBS is available. The Digital Display indicates “00”, the PBS is null. If the “11” is be set, the gate opener won’t work until the PBS system is equipped. The PBS Note: system works only when gate opener is closing. The gate opener will return to its open position when the obstruction blocks the beam from photo eye.
  • Page 21: Adjusting The Limit Switch

    “- -”. When the motor is not running, the Digital Display indicates Adjusting the Limit Switch Note: Before adjusting the limit switch, refer to the chapter of “Install the Opener on the Gate”, and make sure that the rod is fully retracted when the gate is in the fully open position (for Pull-to-Open installation), or in the fully closed position (for Push-to-Open installation).
  • Page 22: Trouble Shooting

    3. Refer to the instructions on how to check gate force and sensitivity adjustments. Trouble Shooting ◆Opener does not run. Digital Display indicator is not on. 1. Check if the power is on. Check the input voltage at the terminal. It should be local AC power. If the voltage measures 0 suing the voltmeter, the power cable may be damaged.
  • Page 23: Quick-Setting Guide

    Quick-Setting Guide...
  • Page 27 8307 S 192nd St Kent WA 98032 USA Phone : 833-926-2323 hello@alekoproducts.com ©2023-2026 ALEKO All Rights Reserved...

Table of Contents