Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Aleko AR 900
Summary of Contents for Aleko AR 900
- Page 1 www.WholesaleGateOpener.com REV 13a...
-
Page 2: Table Of Contents
Table of Contents General Safety ……………………………………..……………………………………..………………….. 2 Preparation for Installation ……………………………………………..…………………………………..…….. 3 Parts List ………………………………………..….…………………………………..…………………………. 4 Optional Accessories Part List ………………………………………..….…………………………………..… 5 Technical Specifications & Feature …………………….……………………..…………………………………..5 Installation Overview ……………………………….…………..…………………………………..……………. 6 Installation of the Operator ……………………………………..…………………………………....……….6 Manual Operation …………………………………………..…………………………………..……………….. 7 Fit the plastic rack reinforced with steel ………………………………………..………………………………... -
Page 3: General Safety
Thank you for purchasing AR900 sliding gate operator. We are sure that the products will be greatly satisfying as soon as you start to use it. The product is supplied with a user’s manual which encloses installation and safety precautions. These should be read carefully before installation and operation as they provide important information about safety, installation, operation and maintenance. -
Page 4: Preparation For Installation
• Do not allow persons or children to remain in the automation operation area. • Keep radio control or other control devices out of children’s reach, in order to avoid unintentional automation activation. • The user must avoid any attempt to carry out work or repair on the automation system, and always request the assistance of qualified personnel. -
Page 5: Parts List
Parts List... -
Page 6: Optional Accessories Part List
Optional Accessories Parts List Technical Specifications & Features Specifications ·Power supply: 120V/60HZ or 230V/50HZ ·Motor: 24VDC ·Absorbed power: 120W ·Gate moving speed: (7 “/second) 18 cm/second ·Max gate weight: 900LBS ·Max torque: 8Nm ·Environmental conditions: from -15°C to +40°C ·Protection class: IP44 REV 13a... -
Page 7: Installation Overview
·Dimensions: 29.5×20×22.5 CM Features: ·Soft start and soft stop ·Midway mode ·Easy to install and low maintain ·Quick selection for the gate open/close direction ·Reliable rolling code technology ·Emergency release key in case of power failure ·Stop/Reverse in case of obstruction during gate opening/closing ·Built in adjustable auto-close (0, 30, 60, 90 seconds) ·Built in max. -
Page 8: Manual Operation
* Before starting installation, ensure that there is no point of friction during the entire movement of the gate and there is no danger of derailment. * Ensure that the Warning Signs are present. Necessary Tools: The following tools may be necessary to install the Gate operator. You will need screwdrivers, an electric drill, wire cutters and a wire stripper, a socket set, and possibly access to a welder. -
Page 9: Fit The Plastic Rack Reinforced With Steel
Fit the plastic rack reinforced with steel 1. Start with gate in closed position 2. There are four sections of plastic rack which is one meter length, each section for standard package. (you can order extra rack from dealer if necessary) 2. -
Page 10: Installation Of The Limit Switch
6. Cut away any excess of the rack (Note: rack length must be longer than actual travel of the gate) 7. Thoroughly fasten the four nuts as well as spring washers onto expansion bolts tightly, enabling the operator is firmly secured on the concrete pad during the whole gate travel. Installation of the Limit Switch Before install limit switch, make sure the gate operator is put in manual operation. -
Page 11: Connecting Of Power Supply
Connecting Of Power Supply The power supply cord should not be smaller than （18AWG）for its diameter. H05R1V-F, 3×0.75mm Connect the live wire, neutral wire and earth wire to the “L”, “N” and “PE” terminal respectively. Connecting Of the Control Board... - Page 12 1. Motor The RED wire of the motor should be connected into the “1” terminal. The GREEN wire of the motor should be connected into the “2” terminal. 2. Limit Switches The RED wire of the limit switches should be connected into the “3” terminal. The BLACK wire of the limit switches should be connected into the “4”...
-
Page 13: Setting Of The Control Board
10. Solar Panel Please refer to the manual instruction of solar panel and controller separated. Setting Of the Control Board WARNING: Cut off the power before change the settings. Keep away from the gate during you set the gate opener system in case of the unexpected gate moving. Always ask the help of professional technician /electrician if you have any question. -
Page 14: Test The Reversing Sensitivity
DIP Switch #6–#7: Auto close time of the gate operator DIP Switch #6: ON – 30 Seconds OFF – 0 DIP Switch #7: ON – 60 Seconds OFF – 0 NOTE: The auto close function would be disabled if both DIP switches are turned to off (factory default setting). -
Page 15: How To Learn Or Erase The Remote
How to learn or erase the remote Learn the remote Press and release the learn button, the REM LED light will be on, then press the key in the remote twice in 2 seconds, the REM LED light will flash for 4 seconds. Now the remote has been learnt successfully. -
Page 16: Maintenance
* Always check the Stop/Reverse in case of obstruction function when performing any maintenance. If this function can’t be made operable, remove this operator from service until the cause of the malfunction is identified and corrected. www.WholesaleGateOpener.com 7106 S 220th St, Kent WA 98032 USA sales@WholesaleGateOpener.com ©2012-2014 ALEKO All Rights Reserved...
Need help?
Do you have a question about the AR 900 and is the answer not in the manual?
Questions and answers