Table of Contents

Advertisement

V-530/550/560/570
Spectrophotometer
Instruction Manual
V -500 f or W i n dow s Ò
P/N:0302-0304C
January 2003

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V-530 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Jasco V-530

  • Page 1 V-530/550/560/570 Spectrophotometer Instruction Manual V -500 f or W i n dow s Ò P/N:0302-0304C January 2003...
  • Page 2: Safety Considerations

    Safety Considerations To ensure operation safety, this instrument must be operated correctly and maintained according to a regular schedule. Carefully read to fully understand all safety precautions in this manual before operating the instrument. Please take a moment to understand what the signal words WARNING!, CAUTION, and Note mean in this manual.
  • Page 3 Warning labels are attached at several locations on this instrument. Do not remove, deface or damage the warning labels. If a warning label peels off the instrument or becomes illegible, contact your local JASCO distributor and state the part number of the label you want to replace.
  • Page 4 Warning for GROUND Warning for FUSE Figure 2 Warning Labels on the V-550/560/570 Back Panel Warning for carrying The weight (in kilograms) of each instrument is as follows: V-530 V-550 V-560 V-570 16.0 30.5 32.0 33.0 When moving the instrument, hold the handgrips at the bottom of the instrument firmly (see Fig.
  • Page 5: Regulatory Statements

    · A "Declaration of Conformity" in accordance with the above standards has been made and is on file at JASCO EUROPE srl, Via Confalonieri 25, 22060 CREMELLA (LC), Italy. FCC Statement (for USA only) Federal Communications Commission Radio Frequency Interference Statement W A R N I N G : T hi s equi pm ent generat es, uses, and can radi at e radi o f requency energy.
  • Page 6: Preface

    This manual should be easily accessible to the operator at all times during instrument operation. When not using the instrument, keep this manual in a safe place. If this instruction manual becomes lost, order a replacement from your local JASCO distributor. The instruction manual is divided into following volumes: 1) Hardware manual: Describes the principles of operation, specifications, maintenance, troubleshooting of this instrument.
  • Page 7: Installation Requirements

    Installation Requirements To ensure operation safety, observe the following conditions: Do not operate the instrument under voltage fluctuations exceeding 10% of the recommended line voltage. Otherwise, the instrument may not function properly. Frequency or spike noise in the power supply should be minimal. Ensure that the instrument is grounded.
  • Page 8: Servicing

    Consumable parts should be ordered according to part number from your local JASCO distributor. If a part number is unknown, give your JASCO distributor the model name and serial number of your instrument.
  • Page 9: Limited Warranty

    Limited Warranty Products sold by JASCO, unless otherwise specified, are warranted for a period of one year from the date of shipment to be free of defects in materials and workmanship. If any defects in the product are found during this warranty period, JASCO will repair or replace the defective part(s) or product free of charge.
  • Page 10: Table Of Contents

    Contents Safety Considerations......................... i Regulatory Statements......................iv Preface ............................v Installation Requirements ......................vi Servicing ..........................vii Notices............................vii Limited Warranty........................viii 1. Introduction ........................... 1 1.1 Layout of this Manual....................... 1 1.2 Foreword and Notation Used.................... 1 1.3 Overview of [Spectra Manager] ..................2 2.
  • Page 11 4.1 [File] menu ........................30 4.1.1 [New...] ..........................30 4.1.2 [Open...]..........................32 4.1.3 [Save]............................ 32 4.1.4 [Save As...] ........................... 33 4.1.5 [Page Setup...] ........................34 4.1.6 [Print Setup...] ........................34 4.1.7 [Print...] ..........................35 4.1.8 [Exit]............................. 35 4.2 [Method] menu ....................... 36 4.2.1 [New...] ..........................
  • Page 12 6.1.1 [Start]............................ 61 6.1.2 [Parameter...] ........................61 6.1.2.1 [Parameter] dialog box ....................61 6.1.2.2 [Data File] dialog box....................63 6.1.3 [Move Wavelength...] ......................63 6.1.4 [Auto Zero]........................... 63 6.1.5 [Exit]............................. 63 6.2 [Help] menu ........................64 7. [Fixed Wavelength Measurement]..................65 7.1 [Measurement] menu ......................
  • Page 14: Introduction

    1. Introduction 1. 1 Layout of t h i s M anual T hi s sect i on descri bes t he l ayout and f unct i on of t hi s m anual . T he V -500 f or W i ndow s Ò i nst ruct i on m anual consi st s of 10 sect i ons, i ncl udi ng t hi s one.
  • Page 15: Overview Of [Spectra Manager]

    T he f ol l ow i ng not at i onal convent i ons are used t hroughout t hi s m anual : General Notation Notation Meaning [Measurement] menu Names of menus, commands, and text boxes are enclosed in square brackets [ ], followed by a description indicating whether [Parameters...] command the function is a menu, command, text box, or other.
  • Page 16 ei ght w avel engt hs can be set and m easured. [ A bs/ % T M et er] program T hi s program reproduces t he anal og spect rophot om et er on t he C R T screen, so you can read t he absorbance (A bs) or t ransm i t t ance (% T ) at an arbi t rary w avel engt h on t he m et er.
  • Page 17: Starting And Exiting Programs And [Spectra Manager]

    2. 1. 3 [ S pect ra M anager] st art up W hen W i ndow s i s st art ed, [ Jasco] -[ S pect ra M anager] al so st art s. (S ee F i g. 2. 2. ) T he [ S pect ra...
  • Page 18 F i gure 2. 2 W i ndow s screen F i gure 2. 3 [ S pect ra M anager] w i ndow I n t he [ S pect ra M anager] w i ndow , m ake sure t he I nst rum ent i n t he [ I nst rum ent s: ] box i s t he spect rophot om et er you are usi ng.
  • Page 19: Exiting

    F i gure 2. 4 M essage boxes duri ng st art up N ot e: C heck t he f ol l ow i ng i f t he m essage on t he ri ght i n F i g. 2. 4 appears. ·...
  • Page 20: Pc And Spectrophotometer Shutdown

    M anager] w i ndow appears. E xi t i ng t he [ S pect ra M anager] program C l i ck [ A ppl i cat i ons] - [ E xi t ] . E xi t i ng W i ndow s E xi t W i ndow s accordi ng t o t he W i ndow s U ser ’...
  • Page 21: Spectra Manager] Menu

    2. 3 [S pect r a M anager] M enu T he [ S pect ra M anager] i s used t o st art m easurem ent , spect ra anal ysi s and envi ronm ent set t i ng usi ng t he spect rophot om et er, and sel ect i ng, f or st art i ng up and shut t i ng dow n t he spect rophot om et er, as w el l as f or set t i ng t he com m uni cat i on port .
  • Page 22 [ O pt i on. . . ] I nst al l t he opt i onal accessory (R ef er t o t he accessory i nst ruct i on m anual ). [ A bout . . . ] D i spl ays t he versi on i nf orm at i on of t he cont rol dri ver of t he spect rophot om et er.
  • Page 23: Quantitative Analysis And Spectrum Measurement

    3. Quantitative Analysis and Spectrum Measurement T hi s sect i on descri bes quant i t at i ve anal ysi s and spect rum m easurem ent . T he param et ers are descri bed onl y bri ef l y i n order t o cl ari f y t he operat i on f l ow . F ol l ow t he procedures out l i ned bel ow i n order t o becom e f am i l i ar w i t h t he operat i on of V -500W .
  • Page 24: Quantitative Analysis Operation

    Proportional expression Linear expression Quadratic expression Third-order expression Segmented line Logistic function Spline function F i gure 3. 2 C al i brat i on curve m odes T he operat or can set w het her t o use st andard m easurem ent dat a (set of concent rat i on/ absorbance) t o cal cul at e t he cal i brat i on curve.
  • Page 25: Calibration Curve Creation

    T he m essage U N D E R I N I T I A LI Z A T I O N appears and m easurem ent param et ers are t ransf erred t o t he spect rophot om et er. W hen t ransf er i s f i ni shed, t he program st art s and t he f ol l ow i ng w i ndow appears. F i gure 3.
  • Page 26 C l i ck <N ew > t o open t he f ol l ow i ng di al og box. F i gure 3. 5 [ Q uant i t at i ve M easurem ent P aram et ers] di al og box C hangi ng m easurem ent param et ers procedure T he [ Q uant i t at i ve M easurem ent P aram et ers] di al og box di spl ays t he i nst rum ent def aul t set t i ngs.
  • Page 27 F i gure 3. 6 [ C al i brat e C urve P aram et ers] di al og box C al i brat i on curve param et er set t i ng S et [ C al i b. curve] t o [ P roport i onal ] . U se t he sam e procedure as f or changi ng param et ers I f [ S t andard bl ank] i s know n, i nput t hat val ue t o t he t ext box.
  • Page 28: Sample Chamber

    F i gure 3. 7 [ Q uant i t at i ve M easurem ent ] di al og box M easuri ng t he st andard bl ank S el ect t he [ B l ank] opt i on but t on. P l ace t he st andard bl ank i n t he cel l hol der of t he sam pl e cham ber.
  • Page 29: Calibration Curve Modification

    [ U se] f i el d changes f rom [ ---] t o [ U se] . T he cursor aut om at i cal l y m oves t o t he next l i ne. N ot e: T he st andard bl ank val ue i s not subt ract ed f rom t he absorbance i n t he st andard dat a di spl ay f i el d. R epeat st eps 2) and 3) as m any t i m es as t he num ber of st andard sam pl es.
  • Page 30: Saving Quantitative Analysis Method

    I nval i dat i ng M ove t he cursor t o t he i ncorrect dat a l i ne. U nsel ect t he [ E nabl e C al i b. D at a] checkbox, and t hen cl i ck <A ppend>. T he [ U se] changes t o [ ---] .
  • Page 31: Unknown Sample Measurement

    3. 1. 6 U nknow n sam pl e m easurem ent C l i ck [ M easurem ent ] - [ M easurem ent . . . ] . T he f ol l ow i ng di al og box appears. F i gure 3.
  • Page 32: Saving Data Sheet

    N ot e: T he l i ne w i t h t he i ncorrect m easurem ent can be i nval i dat ed (see S ect i on 4. 4. 4, “ [ T i t l e. . . ] ” ). 3.
  • Page 33: Exiting Quantitative Analysis

    F i gure 3. 14 [ P ri nt ] di al og box C l i ck <O K > t o pri nt t he quant i t at i ve anal ysi s dat a. 3. 1. 9 E xi t i ng quant i t at i ve anal ysi s C l i ck [ F i l e] - [ E xi t ] t o ret urn t o t he [ S pect ra M anager] w i ndow af t er m easurem ent i s f i ni shed.
  • Page 34: Spectrum Measurement

    3. 2 S pect r um M easurem ent T hi s sect i on descri bes t he procedures f or st art i ng t he S pect rum M easurem ent program , m easuri ng st andard sam pl es, savi ng m easured spect ra t o di sk, and pri nt i ng dat a. 3.
  • Page 35 3. 2. 3 S et t i ng m easurem ent param et ers C l i ck [ M easurem ent ] - [ P aram et er. . . ] . T he f ol l ow i ng di al og box appears. T he di al og box consi st s of t w o pages, [ P aram et er] and [ D at a F i l e] .
  • Page 36 3. 2. 4 S et t i ng t he basel i ne(or M easurem ent ) T he basel i ne def i nes t he “ 0 ” absorbance (100% f or t ransm i t t ance) l evel . T he basel i ne val ue i s subt ract ed f rom t he m easured dat a (di vi ded f or t ransm i t t ance) i n order t o det erm i ne t he correct spect rum of a sam pl e.
  • Page 37 F i gure 3. 19 [ B asel i ne M easurem ent ] (1) di al og box N ot e: I f t he <M easure> but t on i s cl i cked w i t hout put t i ng a check m ark t o [ F ul l W avel engt h] , m easurem ent w i l l st art i m m edi at el y w i t hout di spl ayi ng F i g.
  • Page 38 3. 2. 5 S am pl e m easurem ent P l ace a sam pl e i n t he cel l hol der on t he near-si de of t he sam pl e cham ber, and t hen cl ose t he l i d. Sample Chamber F i gure 3.
  • Page 39: Printing Results

    3. 2. 6 S pect rum save S pect ra can be saved i n a f i l e. C l i ck [ F i l e] - [ S ave A s. . . ] . T he f ol l ow i ng di al og box appears. F i gure 3.
  • Page 40: Instrument Shutdown

    C l i ck [ F i l e] - [ P ri nt . . . ] t o pri nt t he spect ra. 3. 2. 8 I nst rum ent shut dow n E xi t i ng t he [ S pect ra A nal ysi s] program C l i ck [ F i l e] - [ E xi t ] .
  • Page 41: Quantitative Analysis]

    4. [Quantitative Analysis] D oubl e-cl i ck [ Q uant i t at i ve A nal ysi s] i n t he [ S pect ra M anager] w i ndow . T he program st art s and t he f ol l ow i ng w i ndow appears af t er spect rophot om et er i ni t i al i zat i on.
  • Page 42 M anager] . [ M et hod] m enu [ N ew . . . ] C reat es a new cal i brat i on curve. [ O pen. . . ] O pens saved quant i t at i ve anal ysi s m et hod f i l es. [ S ave A s.
  • Page 43: File] Menu

    O pens a saved [ D at a S heet ] f i l e ([ F i l e] -[ O pen. . . ] ) P ri nt s t he dat a f rom t he act i ve w i ndow set by [ P age S et up. . . ] ([ F i l e] -[ P ri nt . . . ] ) 4.
  • Page 44 F i gure 4. 3 [ I nf orm at i on] di al og box F i gure 4. 4 [ D at a S heet ] w i ndow A n unknow n sam pl e can be m easured f rom t he [ D at a S heet ] w i ndow usi ng t he di spl ayed quant i t at i ve anal ysi s m et hod.
  • Page 45: Open

    4. 1. 2 [ O pen. . . ] O pens a saved [ D at a S heet ] f i l e. N ot e: I f an unsaved [ D at a S heet ] or [ C al i brat e C urve] i s i n t he w i ndow w hen [ O pen. . . ] i s cl i cked, a m essage appears t o ask t he operat or w het her t he dat a shoul d be saved.
  • Page 46: Save As

    4. 1. 4 [ S ave A s. . . ] S aves t he act i ve [ D at a S heet ] under a new f i l enam e. M easurem ent param et ers and cal i brat i on curve dat a are al so saved.
  • Page 47: Page Setup

    4. 1. 5 [ P age S et up. . . ] S et s pri nt cont ent s such as [ D at a S heet ] , cal i brat i on curve, or m easurem ent param et ers. F i gure 4.
  • Page 48: Print

    4. 1. 7 [ P ri nt . . . ] P ri nt s t he dat a f rom t he act i ve w i ndow set i n [ P age S et up. . . ] . F i gure 4.
  • Page 49: Method] Menu

    4. 2 [M et h od] m enu 4. 2. 1 [ N ew . . . ] C reat es a new cal i brat i on curve. C l i ck [ N ew . . . ] t o open t he f ol l ow i ng di al og box. N ot e: I f a cal i brat i on curve has not been saved, a m essage appears t o ask t he operat or w het her t o save i t .
  • Page 50 0. 5 2 (L2) 5 (L5) 10 (L10) [ M et hod] N o. of w avel engt hs used i n quant i t at i ve anal ysi s. S el ect s opt i m um num ber. of w avel engt hs (1, 2, or 3) accordi ng t o t he sam pl e condi t i on. 1-w avel engt h: F or com m on sol ut i on sam pl e.
  • Page 51 F i gure 4. 13 [ C al i brat e C urve P aram et ers] di al og box [ G raph S et t i ng] [ C al i b C urve] T he t ype of cal i brat i on curve. C l i ck t he drop-dow n f orm at box and sel ect a t ype.
  • Page 52 [ E nabl e C al i b. D at a] D at a i n t he st andard dat a di spl ay f i el d can be used f or t he cal i brat i on curve by sel ect i ng t he [ E nabl e C al i b.
  • Page 53: Open

    <C ancel >: C l oses t he di al og box w i t hout changi ng t he previ ousl y set w avel engt h. <A ut o Z ero> S et s t he absorbance val ue of t he current w avel engt h t o zero. <O K >...
  • Page 54: Save As

    4. 2. 3 [ S ave A s. . . ] S aves quant i t at i ve anal ysi s m et hod dat a, i ncl udi ng cal i brat i on curve, and m easurem ent param et ers. F i gure 4.
  • Page 55: Information

    4. 2. 5 [ I nf orm at i on. . . ] W hen t he [ M et hod I nf orm at i on] w i ndow i s i n i con f orm , st art i ng t hi s f unct i on opens t he ori gi nal w i ndow agai n.
  • Page 56: Parameters

    <C l ose> C l oses t he [ Q uant i t at i ve M easurem ent ] di al og box. <G ot o W L. . . > M oves t he w avel engt h of t he spect rophot om et er t o a set w avel engt h (see F i g.
  • Page 57: Edit] Menu

    4. 4 [E di t ] m enu 4. 4. 1 [ C opy P i ct ure] C opi es a cal i brat i on curve t o t he cl i pboard as a pi ct ure. 4.
  • Page 58: Font

    4. 5. 1 [ F ont . . . ] S et s t he f ont f or t he [ D at a S heet ] or cal i brat i on curve. W hen t he [ C al i brat e C urve] w i ndow i s act i ve, t he f ol l ow i ng w i ndow opens bef ore t he [ F ont ] di al og box appears.
  • Page 59: Format

    F i gure 4. 27 [ F ont ] di al og box [ F ont ] l i st S el ect a f ont f rom t hi s l i st . [ F ont S t yl e] l i st S el ect a f ont st yl e f rom t hi s l i st .
  • Page 60: Pattern

    [ A ut o] checkbox t o set t he scal e t o t he opt i m al val ue accordi ng t o t he cal i brat i on curve dat a. T hi s f unct i on i s act i ve onl y w hen t he [ C al i brat e C urve] w i ndow i s act i ve.
  • Page 61: Style

    F i gure 4. 32 [ G ri d Li nes] di al og box [ M ai n] S el ect t he [ V ert i cal A xi s] and/ or [ H ori zont al A xi s] checkbox t o di spl ay t he scal e l i ne.
  • Page 62: Marker

    4. 5. 8 [ M arker. . . ] C l i ck [ V i ew ] - [ M arker. . . ] t o set t he t ype, si ze, and col or of t he m arker used t o i ndi cat e speci f i c dat a poi nt s on t he cal i brat i on curve, and w het her t o f i l l t he i nsi de of t he m arker.
  • Page 63: Spectrum Measurement]

    5. [Spectrum Measurement] [ S pect rum M easurem ent ] m easures a sam pl e spect rum . I n t he [ S pect ra M anager] w i ndow , doubl e-cl i ck [ S pect rum M easurem ent ] . T he spect rophot om et er i s i ni t i al i zed and t he f ol l ow i ng w i ndow appears. Title Bar Menu Bar Monitor Bar...
  • Page 64: Measurement] Menu

    [ E xi t ] E xi t s t he spect rum m easurem ent program and ret urns t o [ S pect ra M anager] . [ H el p] m enu [ A bout . . . ] D i spl ays i nf orm at i on such as t he program versi on.
  • Page 65 F i gure 5. 3 [ P aram et ers] di al og box [ P hot om et ri c M ode] S et s t he phot om et ri c m ode. S el ect abl e range: ...
  • Page 66 regi on) N ot e: W hen usi ng t he V -570 f or m easurem ent f rom t he near-i nf rared regi on t o t he vi si bl e regi on i n successi on, t he bandw i dt hs l i st ed i n T abl e 5.
  • Page 67 S canni ng S peed (nm / m i n)                               ...
  • Page 68: Data File] Dialog Box

    <O K > S aves param et ers. <C ancel > R et urns t o t he [ P aram et ers] di al og box w i t hout savi ng t he param et ers. <C ont ent s. . . > D i spl ays t he param et ers sel ect ed f rom t he param et er l i st .
  • Page 69: Baseline

    are saved aut om at i cal l y. [ F i l e N am e] T ext box f or i nput t i ng t he f i l enam e of aut om at i cal l y saved dat a. U p t o 5 charact ers m ay be i nput .
  • Page 70 F i gure 5. 8 [ P aram et ers-O pen] di al og box S el ect i ng a f i l enam e f rom [ P aram et ers Li st ] and cl i cki ng <O K > l oads i t i nt o m em ory and rew ri t es [ B asel i ne param et ers] t o t hose of t he f i l e.
  • Page 71: Move Wavelength

    F i gure 5. 10 [ B asel i ne M easurem ent ] di al og box C l i ck t he <S t art > but t on. B asel i ne m easurem ent st art s. D uri ng m easurem ent , t he f ol l ow i ng di al og box i s di spl ayed.
  • Page 72: Auto Zero]

    F i gure 5. 12 [ G ot o W avel engt h] di al og box [ W avel engt h] T ext box f or i nput t i ng a w avel engt h. <O K > M oves t he spect rophot om et er w avel engt h t o t he set w avel engt h.
  • Page 73: Time Course Measurement]

    6. [Time Course Measurement] M easures changes i n a sam pl e over t i m e at a set w avel engt h. I n t he [ S pect ra M anager] w i ndow , doubl e-cl i ck [ T i m e C ourse M easurem ent ] . T he program st art s, and t he w i ndow show n bel ow opens.
  • Page 74: Measurement] Menu

    [ H el p] m enu [ A bout . . . ] D i spl ays i nf orm at i on such as program versi on. 6. 1 [M easurem ent ] m enu 6. 1. 1 [ S t art ] S t art s t i m e course m easurem ent .
  • Page 75 F i gure 6. 3 [ P aram et er] di al og box [ P hot om et ri c M ode] S et s t he phot om et ri c m ode. S el ect abl e range: ...
  • Page 76: Data File] Dialog Box

    T abl e 6. 1 U l t ravi ol et / vi si bl e regi on bandw i dt h (U V ) nm N ear-i nf rared bandw i dt h (N I R ) nm 0. 1 0.
  • Page 77: Help] Menu

    6. 2 [H el p ] m enu [ A bout . . . ] D i spl ays i nf orm at i on such as program versi on.
  • Page 78: Fixed Wavelength Measurement]

    7. [Fixed Wavelength Measurement] [ F i xed W avel engt h M easurem ent ] m easures sam pl e absorbance or t ransm i t t ance at a f i xed w avel engt h. D oubl e-cl i ck [ F i xed W avel engt h M easurem ent ] i n t he [ S pect ra M anager] w i ndow . T he program st art s and t he w i ndow show n bel ow appears.
  • Page 79: Measurement] Menu

    [ A bout . . . ] D i spl ays i nf orm at i on such as program versi on. 7. 1 [M easurem ent ] m enu 7. 1. 1 [ S t art ] S t art s f i xed-w avel engt h m easurem ent . T o suspend m easurem ent , cl i ck <S t op>. 7.
  • Page 80: Parameter

    7. 1. 3 [ P aram et er. . . ] S et s param et ers, and saves t hem t o t he hard di sk. C l i ck [ M easurem ent ] - [ P aram et er. . . ] t o di spl ay t he di al og box show n bel ow . F i gure 7.
  • Page 81 N ot e: W hen usi ng t he V -570 f or m easurem ent f rom t he near-i nf rared regi on t o t he vi si bl e regi on i n successi on, t he bandw i dt hs l i st ed i n T abl e 7. 1 shoul d be pai red. I f t he bandw i dt h i s set t o t he sam e (nearl y equal ) val ue, noi se i n t he near-i nf rared regi on m easurem ent val ue w i l l i ncrease.
  • Page 82: Goto Wavelength

    <O K > E nds param et er set t i ng. C l i ck t hi s but t on t o t ransf er t he set param et ers t o t he spect rophot om et er. A t t he sam e t i m e, t he di al og box cl oses. <C ancel >...
  • Page 83: Abs/%T Meter]

    8. [Abs/%T Meter] [ A bs/ % T M et er] i s a di spl ay of t he anal og spect rophot om et er on t he screen. Y ou can read A bsorbance (A bs) or t ransm i t t ance (% T ) at a set w avel engt h. I n t he [ S pect ra M anager] w i ndow , doubl e-cl i ck [ A bs/ % T M et er] .
  • Page 84  M edi um : M ovi ng average duri ng about 1 sec  S l ow : M ovi ng average duri ng about 4 sec [ B and w i dt h] S pect ral bandw i dt h. S el ect abl e range vari es accordi ng t o t he m odel . V -530: F i xed at 2 nm V -550/ 560:...
  • Page 85: Environment]

    9. [Environment] S yst em hardw are set t i ng, sel f -di agnosi s, opt i onal accessory set t i ng, and w avel engt h correct i on can be st art ed f rom t hi s m enu. I n t he [ S pect ra M anager] w i ndow , doubl e-cl i ck [ E nvi ronm ent ] .
  • Page 86: Diagnosis] Menu

    i s t urned O N . I f bot h l am ps are sel ect ed, t he l i t l am p changes f rom hal ogen t o deut eri um at t he set [ W avel engt h f or Lam p E xchange] w avel engt h.
  • Page 87: Accessories Setting]

    <R et ry> D oes sel f -di agnosi s agai n. <C l ose> E nds sel f -di agnosi s. 9. 3 [A ccessori e s S et t i n g] S et s t he condi t i ons of t he opt i onal i nt el l i gent accessori es t hat have com m uni cat i on f unct i ons. F or det ai l s, ref er t o t he i nst ruct i on m anual s f or t he accessori es.
  • Page 88: Wavelength Correction]

    T em perat ure C ont rol l er [ C ont rol ] check box W hen checked, t he t em perat ure cont rol l er i s used. [ T em perat ure] S et t em perat ure. [ S t i rrer] W hen checked, t he st i rrer i s used.
  • Page 89: Appendix

    10. Appendix 10. 1 S pect r a M anager I n st a l l a t i o n 10. 1. 1 B ef ore i nst al l at i on B ef ore i nst al l i ng t he [ S pect ra M anager] , conf i rm t he f ol l ow i ng: T he com put er and al l peri pheral devi ces are properl y connect ed.
  • Page 90 F i gure 10. 2 [ C ont rol P anel ] D oubl e-cl i ck [ A dd/ R em ove P rogram s] i n t he [ C ont rol P anel ] w i ndow . T he w i ndow bel ow appears. F i gure 10.
  • Page 91 S el ect [ I nst al l / U ni nst al l ] , t hen cl i ck t he <I nst al l (I )> but t on. T he w i ndow bel ow appears. F i gure 10.
  • Page 92: Inputting Operator Name Or Company Name

    C l i ck t he <F i ni sh> but t on. T he w i ndow bel ow appears. F i gure 10. 6 [ S pect ra M anager] f or W i ndow s S et up C l i ck t he <N ext >...
  • Page 93: Setting The Program Directory

    C l i ck t he <N ext > but t on. T he di al og box show n i n F i g. 10. 8 appears. F i gure 10. 8 T arget program di rect ory set t i ng f or [ S pect ra M anager] 10.1.2.3 Setting the program directory I nput t he dri ve and nam e of t he t arget [ S pect ra M anager] program di rect ory.
  • Page 94: Copying Files To Hard Disk

    A f t er t he f i l es have been copi ed, t he [ S et up] program creat es a Jasco group. A di al og box appears,...
  • Page 95: Installing Spectra Manager From Cd-Rom

    i ndi cat i ng t hat i nst al l at i on has f i ni shed. C l i ck <O K >. 10. 1. 3 I nst al l i ng Spectra Manager from CD-ROM O pen [ C ont rol P anel ] , sel ect [ A dd/ R em ove P rogram s] t o run program . F i gure 10.
  • Page 96 T he next st ep w i l l be t o set up each of t he vari ous appl i cat i ons. C l i ck <st art > on t he t askbar and proceed t o [ program ] , t hen [ Jasco] , t hen [ S pect ra M anager set up] and cl i ck t o run program .
  • Page 97: Setting The Serial Port (Rs-232C)

    10. 2 S et t i n g t h e S eri a l P ort (R S -232C ) T he seri al port def aul t val ue i s [ C O M 1] . T he seri al port num ber m ust be changed w hen t he S pect rophot om et er i s cont rol l ed t hrough anot her port .
  • Page 99 JASCO Corporation 2967-5 Ishikawa-machi, Hachioji TOKYO, Japan Printed in Japan...

This manual is also suitable for:

V-560V-550V-570

Table of Contents

Save PDF