• If Aladin TEC 3H fails at any time during the dive, the dive must be terminated, and appropriate surfacing procedures (including a slow ascent and a 3 to 5 minute safety stop at 5m /15ft) should be initiated immediately.
After a reset of the remaining saturation do not dive for at least 48 hours. Altitude and diving • Do not dive at altitudes higher than 4000m (13000ft). • After a dive do not rise to altitudes that Aladin TEC 3H prohibits via the flashing altitude range number (see page 30). Flying after diving •...
- equipped with Scubapro innovative technology - while diving. We thank you for choosing Aladin TEC 3H and we hope you will enjoy safe dives in the future! Further information on Scubapro and Scubapro products can be found on our web page at www.scubapro.com.
Quick reference Quick reference Time of day / Date Do not fly icon Decompression depth Setting icon Desaturation time (DESAT) No-dive warning Service icon Duration of no-dive warning Duration of surface interval Dive time / No-fly time / Current depth SOS duration Altitude sections Repetitive dive number...
Page 6
Operating scheme Display switched off Gas d O Gas 2 O Gas 1 O Logbook Diveplanner Page 1 Surface Oxygen Oxygen Oxygen DEPTH DIVE TIME interval Dive time – concentration concentration concentration – – – depth No-stop dive Battery Date of No-stop time performance the dive...
Introduction to Scubapro LogTRAK ................10 Switching on the display ....................14 How to navigate Aladin TEC 3H at the surface .............. 14 Checking the desaturation time ..................15 Checking the surface interval ..................15 2.10 Displaying the date ..................
Page 8
List of chapters 4.5.3 Desaturation time, No-fly time and No-dive warning ..........29 Diving in mountain lakes ....................30 4.6.1 Altitude ranges ....................30 4.6.2 Decompression dives in mountain lakes ..............31 Gauge Mode .........................32 Diving with microbubble (MB) levels ................34 4.8.1 Comparison of dives with MB level L0 and MB level L5 ......
The data can be transmitted with an infrared interface (IrDA) and LogTRAK software to a Windows personal computer. ® LogTRAK software CD is included with the Aladin TEC 3H package. Infrared interfaces are available in PC. LogTRAK Aladin TEC 3H...
On submerging in water the water contacts switch on Aladin TEC 3H automatically. WARNING If you have chosen the option "Water contacts off" ("set 1", ->70), Aladin TEC 3H will turn on with a delay of up to 1 minute into the dive. This will affect functioning of the computer.
Page 11
System and operation Download dive profiles From LogTRAK, by selecting Dive -> Download Dives you can transfer the Aladin TEC 3H Logbook to your PC or Mac. There are three main views each showing a specific part of your dive logs: Profile shows the graphical data of the dive.
Page 12
Change warnings/settings of the Aladin TEC 3H and reading the computer information By selecting Extras -> Read Dive Computer settings you can enable/disable warnings that cannot be enabled or disabled by using the menus on the Aladin TEC 3H unit.
Page 13
System and operation Read the chapter Warnings and alarms about the possible selections that you can modify on your Aladin TEC 3H. You may also change the shown units between metric/imperial. Select Extras -> Options -> measurement units:...
If there is a remaining saturation from the last dive or from a change of altitude, Time of day display Aladin TEC 3H also displays the "do not fly" time, the "do not fly" icon, the current altitude range and the prohibited altitude range (->30).
2x or 3 x (depending on whether there is desaturation time left). Aladin TEC 3H displays the estimated remaining battery performance for 5 seconds as a bar graph. If the bar graph shows 3 segments the battery warning appears ->16 and Battery condition / the battery has to be replaced ->76.
Diving not possible, dive planner and settings are disabled Aladin TEC 3H marks dives started with 3 or less segments in the logbook with the battery symbol. Logbook information is not lost even when the battery is removed for a long time.
System and operation / SOS 2.13 Switching off the display From the time of day display you can switch off Aladin TEC 3H by pushing On the surface Aladin TEC 3H switches off automatically after 3 minutes without operation. 2.14 Alarm clock The alarm clock goes off only at the surface.
DIVING WITH ALADIN TEC 3H 4.1 Terminology / Symbols The information on the display of Aladin TEC 3H varies depending on the kind of dive and the dive phase. For information about diving with microbubble (MB) levels see page 34. Specific features “Diving...
Diving with Aladin TEC 3H 4.1.2 Display during decompression phase Decompression stop Total ascent time to surface (7min) All required decompression Time stops must be observed. Deepest decompression DEPTH DIVE TIME stop depth 2min DECO Decompression STOP CNS O stop duration...
Maximum Operating Depth (MOD). When you enter the settings for the gas mixture, Aladin TEC 3H will display the max limit setting and the corresponding MOD. Aladin TEC 3H warns you audibly and visually once the depth is reached at which the ppO reaches the maximum allowed value ->26.
If you turn off the sound you will have no audible warnings. Without audible warnings you could inadvertently get into potentially hazardous situations which could result in death or serious injury. WARNING Serious injury or death may result from failing to immediately respond to alarms given by Aladin TEC 3H. 4.2.1 Attention messages 4.2.2 Alarms...
Functions during the dive 4.3 Preparation for the dive You have to check the settings of Aladin TEC 3H especially before the first dive. All settings can be checked and changed directly at Aladin TEC 3H or via LogTRAK. 4.3.1 Setting the gas mixture and ppO...
WARNING If you have chosen the option "Water contacts off" ("set 1" or LogTRAK), Aladin TEC 3H will turn on with a delay of up to 1 minute into the dive. This will affect functioning of the computer. Make sure that the computer is on before starting the dive.
Functions during the dive If a dive lasts longer than 199 minutes the dive time display starts again at 0 minutes. 4.4.4 Current depth / O % mix Current depth is given in 10cm increments in metric setting and 1ft increments in imperial setting.
• In case of an improper ascent Aladin TEC 3H may require a decompression stop even within the no-stop phase because of the danger of microbubble formation. •...
The MOD is a function of ppO max and the mixture used. If during the dive the MOD is reached or exceeded Aladin TEC 3H sends an audible attention message and the MOD is displayed (flashing) in the lower left corner.
Functions during the dive • Aladin TEC 3H will display CNS O % values exceeding 199 % with 199 %. • Aladin TEC 3H displays CNS O % values above 50%. 4.4.10 Nitrogen loading bar graph The nitrogen loading bar gives a graphical representation of how close to decompression you are. As you absorb nitrogen during the dive, more and more segments of the bar will light up.
Ascent time greater than 99 minutes is displayed as " – – ". Total ascent time WARNING On all dives with Aladin TEC 3H, make a safety stop for at least three minutes at a depth of 5m (15ft). 4.4.12 Safety stop timer...
4.5.2 Residual nitrogen bar graph The segments in the residual nitrogen bar graph will gradually turn off as Aladin TEC 3H follows the offgassing of your tissues during your surface interval. There is a 1:1 equivalence in the meaning of the segments between diving and surface.
Surface interval If Aladin TEC 3H detects a situation of increased risk (due to the potential of microbubble accumulation from previous dives or a CNS O level above 40%), the no-dive symbol No-dive will appear on the display.
Altitude ranges 3280ft 13.12psi 6.2 Prohibited altitude WARNING Flying while Aladin TEC 3H displays "do not fly" may lead to serious Ascent to altitude range injury or death from decompression sickness. 3 and 4 prohibited. Max allowed altitude: 2650 m (8694ft).
(If Aladin TEC 3H shows “ – – – “ the gauge mode cannot be switched “on” or “off”. Aladin TEC 3H shows “ – – – “ for 48 hours after a dive in gauge mode and as long as there is remaining desaturation after a dive in computer mode.)
Page 33
Minutes Seconds After diving in gauge mode Aladin TEC 3H shows the remaining time span during which it cannot be used in computer mode. Once the waiting period is over, the gauge mode can be switched off manually. The no-fly time after diving in gauge mode is 48 hours.
(level stop) sooner than a diver using level L0. If a diver ignores a required level stop, Aladin TEC 3H will cascade to a lower MB level and the dive can not be completed with the initially chosen MB level. E.g. if a diver sets level L4 on Aladin TEC 3H prior to the dive and during the dive ignores the recommended stops Aladin TEC 3H will automatically adjust the setting to level L3 or lower.
4.8.1 Comparison of dives with MB level L0 and MB level L5 When two Aladin TEC 3H are used simultaneously, one unit is set for example to MB level L5, the other to L0, the no-stop time will be shortened and level stops will be required before the diver has the obligation of a decompression stop.
> (Tank pressure)… 4.8.3 Preparation for a dive with MB levels Setting the MB level To change the MB level Aladin TEC 3H must be in user mode (time of day display). 1. Push until the symbol for MB levels until appears.
DEPTH DIVE TIME MB no-stop time While diving with MB levels L1 to L5 Aladin TEC 3H will display the NO STOP MB no-stop time instead of the ordinary no-stop time. Within the MB no-stop time no level stops are required.
The warning “MB level reduced” is activated if the diver ascends more than 1.5m (5ft) above the required level stop. Aladin TEC 3H reduces the MB level, an attention beep* goes off and the new MB level is shown in the lower left corner.
Diving with microbubble (MB) levels Decompression obligation Aladin TEC 3H calculates and displays level stops to reduce microbubble formation, but it also calculates the diver’s decompression data. WARNING Avoid decompression dives when diving with MB levels. How to avoid decompression stops:...
Repetitive dives and MB levels: If during a dive a level stop is being ignored and the diver starts another descent shortly afterwards, Aladin TEC 3H might immediately request level stops. To complete the dive with the initially set MB level all level stops must be observed.
Spending 2 or 15 minutes at 30m/100ft would result in the same deep stop of 15m/50ft. With PDIS, as the name suggests, Aladin TEC 3H interprets your dive profile and suggests an intermediate stop that is a function of your nitrogen uptake so far. The PDI stop will therefore change through the course of the dive to reflect the continuosly changing situation in your body.
PDIS (Profile Dependent Intermediate Stop) 4.9.2 How does PDIS work? The mathematical decompression model in Aladin TEC 3H, called ZH-L8 ADT MB, tracks your decompression status by dividing your body into 8 so-called compartments and mathematically following the uptake and release of nitrogen in each with the appropriate laws of physics. The various compartments simulate parts of your body such as central nervous system, muscles, bones, skin and so on.
NO to indicate the fact that you have not performed the PDI stop. If Aladin TEC 3H is displaying a decompression obligation when you reach the PDIS depth during an ascent, all rules apply the same way, but the 2-minute countdown runs in the background and is not displayed on the screen.
Page 44
PDIS (Profile Dependent Intermediate Stop) NOTE: Aladin TEC 3H issues no warnings relating to a missed PDI stop. When diving with MB levels, PDIS follows the same rules as described above. MB levels, however, introduce stops earlier and deeper than the L0 base algorithm. As such, the PDIS display may be delayed and for certain dives it may not be displayed at all.
Aladin TEC 3H enables you to use up to 3 different Nitrox mixtures during the same dive. Tank 1 contains the bottom mix (gas 1), tank 2 the travel mix and tank d contains the deco mix (gas d).
Page 46
3. If you set gas 2 and gas d to “– – O %”, Aladin TEC 3H will compute the dive considering gas 1 only. Aladin TEC 3H will only accept gas switch depths (MOD gas 2 / gas d) as input where the maximum partial pressure of oxygen (ppO max), as pre-set manually (->22 point 5) or by means of LogTRAK, are...
Page 47
(MOD gas 2 /gas d). If a diver ignores a required change or changes the mixture belatedly, Aladin TEC 3H will readjust the decompression calculation accordingly. In case of an ignored switch the dive computer will then base its calculations on...
Page 48
(no switch to gas 2 / deco gas). This is the calculation that Aladin TEC 3H would switch to in case, having reached the switch depth, the diver did not confirm the switch. The decompression information and the O % blink.
Page 49
Diving with 2 or 3 gas mixtures Gas 1 active, MB level L0 DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DEPTH DIVE TIME DIVE TIME DECO DECO DECO DECO STOP STOP STOP STOP CNS O CNS O Decompression Tank...
Page 50
If a diver fails to confirm the change of gas mixture or interrupts the switching procedure by pressing , Aladin TEC 3H displays “GAS 1” / “GAS 2”, the MOD and the oxygen fraction for 5 seconds. Aladin TEC 3H continues to calculate with gas 1 / gas 2 only and adapts the decompression calculation...
Page 51
If after the decompression calculation has readjusted itself to reflect the failed switch the diver goes again below the switch depth (MOD of gas 2 / gas d), Aladin TEC 3H will revert to the decompression calculation that considers gas 2 / gas d also, since upon ascending again the diver will have a renewed opportunity to perform the switch once the switch depth is reached.
4.11.1 Preparation for the CCR dive You have to check the settings of Aladin TEC 3H especially before the first dive. All settings can be checked and changed directly at Aladin TEC 3H or via LogTRAK. Switching the CCR option on and off In order to enable CCR diving you must turn on the CCR option in the SET 1 menu ->68.
Page 53
Change the ppO (+) and (–) 5. By pushing you can change the ppO in the range of 0.3 to 0.95bar. Aladin TEC 3H will now display the corresponding MOD for the new ppO 6. Confirm your ppO settings with 7. Push until the SP2 menu appears.
Page 54
• If CCR is enabled at the SET1 in surface mode and up to a depth of 0.8m Aladin TEC 3H will display “CC” in the lower right corner of the display instead of a percentage value.
(setpoint 1/2). If a diver ignores a required change or changes the SP1 / SP2 belatedly, Aladin TEC 3H will readjust the decompression calculation accordingly. In case of an ignored switch the dive computer will then base its calculations on the...
Page 56
SP2 not used (decompression information relative to SP1 only). This is the calculation that Aladin TEC 3H would switch to in case, having reached the switch depth, the diver did not confirm the switch. The decompression information and the O % blink.
Page 57
CCR Diving SP1 active, MB level L0 DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DIVE TIME DEPTH DIVE TIME DECO DECO DECO DECO STOP STOP STOP STOP CNS O CNS O Decompression Tank Temperature MOD SP1 Time pressure...
Page 58
When the switch depth is reached an audible warning goes off and MOD blinks as long as the current depth is below MOD. Below SP1 MOD, Aladin TEC 3H calculates according to SP1 ppO2 content; this may lead to long decompression requirement since nitrogen fraction increases above the diluent content.
Page 59
CCR Diving DEPTH DIVE TIME MOD SP2 Selected ppO SP2 x100 3. Press to confirm the switch. The text is shown for 5 seconds without blinking. DEPTH DIVE TIME Change to bottom setpoint confirmed To interrupt the switch process at any point, press 2x Changing form bottom SP2 to SP1 Time Switching range...
Page 60
CCR Diving Switch depth DEPTH DIVE TIME Switch from bottom SP2 to SP1 MOD SP1 Procedure: 1. Switch your CCR from SP2 to SP1 and start breathing. 2. Confirm the change by pressing within 30 seconds. “SP1” and the oxygen fraction of the Diluent is displayed for 5 seconds without blinking.
Page 61
If a diver fails to confirm the change of setpoint or interrupts the switching procedure by pressing 2x , Aladin TEC 3H displays “SP2”, the MOD and the ppO2 for 5 seconds. Aladin TEC 3H continues to calculate with rebreather injecting 100% Oxygen (maximum reached ppO2 depends on ambient pressure) and adapts the decompression calculation accordingly.
(SP1 and SP2). 5.1 Planning a no-stop dive To select the dive planner Aladin TEC 3H must be in user mode (time of day display). Push until the symbol for the dive planner PLn appears. (The dive planner cannot be selected in gauge mode.)
If the no-dive warning and its duration has been displayed, Aladin TEC 3H proposes this time – rounded up to the next 15 minutes – as surface interval.
. Aladin TEC 3H calculates the decompression information for this set bottom time. If an MB level (L1-5) is selected, Aladin TEC 3H calculates the level stop data. CNS O2% values higher than 199% will be displayed as 199 %.
6.1 Survey A dive is entered in the logbook if the dive time is longer than 2 minutes. Aladin TEC 3H records the profiles of about 15 hours of diving. This information can be transferred to a PC with the standard infrared interface (IrDA) and the Windows software LogTRAK.
Page 66
Logbook Page 2 Altitude range (if >0) Repetitive dive number Starting time CNS value at the end of the dive Minimum temperature Push to get more information about the dive. Page 3 Gas used gives the consumed gas amount on that dive. Page 4 SOS if applicable If a dive is started within adaptation time (after a change of altitude),...
Page 67
Logbook Statistic information From the time of day display you can get the following statistic information over all dives. Push Deepest dive DEPTH DIVE TIME Longest dive Cumulative bottom time Leaving the logbook By pushing once or twice you can exit the Number of dives logbook.
Settings SETTINGS 7.1 Menu "set 1" With menu "set 1" or LogTRAK you can configure the following items (dive functions): Setting Range Default Page • CCR mode on / off • Depth alarm 5-100m / 15-330ft 40m/130ft • Dive time alarm 5-195 min 60min •...
Page 69
Settings Setting the dive time alarm 1. Confirm that you wish to change the dive time alarm by pushing 2. Change the value in increments of 5 minutes by pushing 3. Switch between 'on' or 'off' by pressing 4. Confirm the setting with Setting the safety stop counter time 1.
Page 70
2. Switch between "on" or "off" by pressing 3. Confirm the setting with Switching the water contacts on and off On submerging in water the water contacts switch on Aladin TEC 3H automatically. WARNING If you chose the option "Water contacts off", Aladin TEC 3H will turn on with a delay of up to 1 minute into the dive.
/ high • Sound on / off • Show Aladin TEC 3H electronic ID Starting from the time of day display push until "set 2" appears. Confirm that you wish to enter into the menu of "set 2" by pushing...
Page 72
Settings Setting the alarm clock time The alarm clock goes off only at the surface. "Sound" must be turned "on" in "set 2". 1. Confirm that you wish to set the alarm time by pushing The hours start to flash. 2.
Page 73
Setting the "sound" to "off" applies also to surface functions (mountain alarm, wake-up alarm, change of altitude range). Showing the hardware electronic ID of Aladin TEC 3H This number is needed when reporting problems or for other maintenance related issues.
Check Aladin TEC 3H high pressure connection and hose condition periodically and service them at least every 2 years. Rinse Aladin TEC 3H carefully with fresh water after each use and to have the batteries changed when needed ->76. To avoid possible problems with your Aladin TEC 3H, the...
On the surface: if service icon and error code "E3" appear, replace the battery ->76. All error codes other than E3: Aladin TEC 3H must not be used for any further dives. Take your dive computer to an authorized Scubapro dealer.
To replace the battery you need a coin or a universal tool and a clean cloth. WARNING • A leaking battery cap may lead to the destruction of Aladin TEC 3H by water seeping in or cause Aladin TEC 3H to switch off without prior notice. •...
Insert the new battery, with "+" pointing outwards, into the battery compartment. After battery replacement Aladin TEC 3H will perform an automatic test (8s) and gives a short beep when the test is done. WARNING 10.
Page 78
Appendix Your dive instrument is manufactured with high-quality components that can be recycled and reused. Nevertheless these components, if not properly managed in accordance with the regulations on waste electrical and electronic equipment, are likely to cause harm to the environment and/or to human health.