Black Horse Model P47 THUNDERBOLT Instruction Manual Book
  1. Manuals
  2. Brands
  3. Black Horse Model Manuals
  4. Toy
  5. P47 Thunderbolt
  6. Instruction manual book
Black Horse Model P47 THUNDERBOLT Instruction Manual Book

Black Horse Model P47 THUNDERBOLT Instruction Manual Book

Hide thumbs Also See for P47 THUNDERBOLT:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL BOOK
SPECIFICATION
     Wingspan :
     Length
:
     Weight :
     Engine :
     Radio :
     Servo :
1,620 mm
1,340 mm
3.8 Kg
15 CC Gas
8 Channels
8Servos + 2 servos Retract (HITEC HS-75BB)
ITEM CODE: BH 36.
64 in.
53 in.
8.36 Lbs.
Made in Vietnam.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P47 THUNDERBOLT and is the answer not in the manual?

Questions and answers

Related Manuals for Black Horse Model P47 THUNDERBOLT

Summary of Contents for Black Horse Model P47 THUNDERBOLT

  • Page 1 INSTRUCTION MANUAL BOOK ITEM CODE: BH 36. SPECIFICATION      Wingspan : 1,620 mm 64 in.      Length 1,340 mm 53 in.      Weight : 3.8 Kg 8.36 Lbs. ...
  • Page 2 P47 - THUNDERBOLT. INSTRUCTION MANUAL. This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your P-47 THUNDERBOLT. Use the parts listing below to identify all parts. WARNING. Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is capable of causing injury to people or property.

  • Page 3: Safety Precaution

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. Caution: this model is not a toy! Caution! do not heat the film more than is If you are a beginner to this type of powered absolutely necessary. If the air or the iron is model, please ask an experienced model flyer too hot, the film may melt and holes may be for help and support.
  • Page 4 P47 - THUNDERBOLT. INSTRUCTION MANUAL. REPLACEMENT SMALL PARTS 3 x 15mm 3 x 15mm 3 x 12mm 1.Door mounting wheel. INSTALLING THE AILERON - FLAP 2.Retract main gear(Left& Right). SERVOS. 1) Install the rubber grommets and brass   3. Fuel tank. eyelets onto the aileron - flap servos.
  • Page 5 P47 - THUNDERBOLT. INSTRUCTION MANUAL. C/A glue. C/A glue. C/A glue. C/A glue. C/A glue. C/A glue. C/A glue. C/A glue. Bottom side. Repeat the procedure for the other top Flap . wing .
  • Page 6 P47 - THUNDERBOLT. INSTRUCTION MANUAL.  2) Using the thread as a guide and using masking tape, tape the servo lead to the end of the thread: carefully pull the thread out. When you have pulled the servo lead out, 3mm x 20mm.

  • Page 7: Installing The Aileron Linkages

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. INSTALLING THE AILERON LINKAGES. Installing the aileron linkages as pictures below. 50mm 2x8mm. Repeat the procedure for the other wing Attach the clevis to the outer hole in the con- half. trol horn. II. FLAP. 1.INSTALLING THE FLAP SERVOS.
  • Page 8 P47 - THUNDERBOLT. INSTRUCTION MANUAL. 2. INSTALLING THE FLAP CONTROL HORN. INSTALLING THE FLAP LINKAGES. Installing the aileron linkages as pictures below. 3 x 20 mm 50mm 2x8mm. 2 x 8 mm Secure. Secure. Secure. Control horn of the flap...
  • Page 9 P47 - THUNDERBOLT. INSTRUCTION MANUAL. Bottom of wing. Repeat the procedure for the other wing half. INSTALLING RETRACTABLE LANDING GEAR. 3x15mm. 3x15mm. Mark point. Retract pushrod Drill 2mm hole. 3x 15mm...
  • Page 10 P47 - THUNDERBOLT. INSTRUCTION MANUAL. Secure. Secure.
  • Page 11 P47 - THUNDERBOLT. INSTRUCTION MANUAL. Drill a hole 3.5mm diameter 3 x 4mm Drill a hole 3.5mm diameter Secure. Secure.
  • Page 12 P47 - THUNDERBOLT. INSTRUCTION MANUAL. Servo. 3 x 6mm Secure. Connector. Secure. Connector. Servo of retractable. Secure.

  • Page 13: Installing The Engine Mount

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. INSTALLING THE ENGINE. Bottom side. Repeat the procedure for the other wing half. INSTALLING THE ENGINE MOUNT. 5 x30mm. See pictures below: Front view. Drill a hole 5.2mm diameter...

  • Page 14: Installing The Throttle - Cable

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. Secure. Throttle cable. INSTALLING THE THROTTLE - CABLE. 1. Install one adjustable metal connector  through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector.
  • Page 15 P47 - THUNDERBOLT. INSTRUCTION MANUAL. When the stopper assembly is installed in the tank, the top of the vent tube should rest just below the top surface of the tank. It should not touch the top of the tank. Tygon gas tubing not included.
  • Page 16 P47 - THUNDERBOLT. INSTRUCTION MANUAL.  8) Feed three lines through the fuel tank compartment and through the pre-drilled hole in the firewall. Pull the lines out from behind the engine, while guiding the fuel tank into place. Push the fuel tank as far forward as possible, the front of the tank should just about touch the back of the firewall.
  • Page 17 P47 - THUNDERBOLT. INSTRUCTION MANUAL. Bottom side Drill a hole 3mm diameter. 3 x 12mm. Trim and cut. Secure 3X12mm.  2) While keeping the back edge of the cowl flush with the marks, align the front of the cowl with the crankshaft of the engine. The front of the cowl should be positioned so the crankshaft is in nearly the middle of the cowl opening.

  • Page 18: Horizontal Stabilizer Installation

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. Front view. HORIZONTAL STABILIZER INSTALLATION. Horizontal stabilizer installation. See picture below. Bottom side. Secure. C/A glue Front view. ELEVATOR INSTALLATION. SERVO INSTALLATION. 1. Install the rubber grommets and brass  collets into the elevator servo. Test fit the servo into the servo tray.
  • Page 19 P47 - THUNDERBOLT. INSTRUCTION MANUAL. C/A glue C/A glue 9 mm Epoxy glue. 142 mm C/A glue...

  • Page 20: Elevator Pushrod Installation

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. ELEVATOR PUSHROD INSTALLATION. Top elevator Pushrod install as same as method of pushrod wing. See pictures below: 2 x 8mm ELEVATOR CONTROL HORN INSTALLA- TION. Elevator control horn install as same as the way of aileron control horn. Please see pictures below.

  • Page 21: Vertical Installation

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. Secure. Secure. Hinge. Top side. VERTICAL INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: Rudder servo C/A glue.

  • Page 22: Rudder Pushrod Installation

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. Rudder control horn. RUDDER PUSHROD INSTALLATION.  1. Rudder pushrod install as same as C/A glue. the way of aileron control horn.  2. Rudder push - pull system install as same as picture below. Top side.

  • Page 23: Mounting The Tail Wheel Bracket

    P47 - THUNDERBOLT. INSTRUCTION MANUAL.      2) Using a pen, mark the locations of the two mounting screws. Remove the tail wheel bracket and drill 1mm pilot holes at the loca- tions marked. Rudder pushrod. Mark point. MOUNTING THE TAIL WHEEL BRACKET.

  • Page 24: Installing The Switch

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. switch of battery Bottom side. INSTALLING THE RECEIVER AND BATTERY. 1) Plug the servo leads and the switch       lead into the receiver . You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier Top side.

  • Page 25: Wing Attachment

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. See picture wing attach to fuselage. Wing bolt. Battery Receiver Left wing. WING ATTACHMENT.  Locate the aluminium wing dihedral brace. 19mm 422mm *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily.

  • Page 26: Control Throws

    P47 - THUNDERBOLT. INSTRUCTION MANUAL. Top side. CONTROL THROWS. 1) We highly recommend setting up a       BALANCING. plane using the control throws listed. 1) It is critical that your airplane be bal-  2) The control throws should be meas- ...

Table of Contents