Rotate And Flip The Blades; Replace The Blades; Keep It Clean; Cleaning The Body - Worx landroid Instruction Manual

A. Rotate and flip the blades
®
Your Landroid M carries the Blades that are all screwed onto the Blade Turning Disc (13). The Blades allow the
®
Landroid M do its job and need care and attention. Every once in awhile, you should simultaneously rotate and flip all
blades for a perfect cut. When rotating and flipping the Blades, make sure all the Blades are adjusted at the same time
or else it could make the Blade Disc off balance. If your Landroid
should last one season if they are rotated and flipped every month. Always check to see if the Blades are chipped or
damaged and replace them if they are.
B. Replace the blades (See Fig. L)
After some time, usually every season, your Landroid
will need to be replaced. Your Landroid
while using Blades of different age and quality. So when replacing
the Blades, make sure to replace all of them at the same time.
You can replace them with one of the three spare Blade kits and
extra Blade screws supplied with your Landroid
Before attempting to replace your Landroid
power off and put on protective gloves. Then follow these steps:
1. Gently flip the Landroid
2. Remove the battery cover and remove the battery.
3. Take the screws off the Blades with a screwdriver.
4. Firmly screw on the new Blades.
5. Refit the battery and the battery cover.
IMPORTANT: After screwing the Blade to the Blade
Disc, make sure the Blade is able to spin freely.

6.2 Keep it clean

WARNING: Before cleaning turn your Landroid
OFF by pressing the ON/OFF Button. Put on
protective gloves before cleaning the Blade Turning Disc
(13) and do not use running water. (See Fig. M)
A. Cleaning the body
®
Your Landroid M will live a much happier and longer life if it is
cleaned regularly. Although, as your Landroid
machine, you will need to take care when cleaning, so DO NOT use
a hose, high pressure washers or otherwise pour running water on
®
your Landroid M, it is best to use a spray bottle filled with water .
When cleaning the machine body use a soft brush or clean cloth and
avoid using solvents or polishes (See Fig. M). Lastly, make sure that
you remove all build up of grass clippings and debris.
B. Cleaning the Underside
Again, it is important that you power the Landroid
before touching the Blade Turning Disc (13).
®
First, flip your Landroid M upside down to expose its underside. Here you will see the Blade Disc, the chassis, and the
Front Wheel (15) and Driving Wheel(10). Clean everything thoroughly with a soft brush or moist rag.
Rotate the Blade Disc to make sure it moves freely and that there is not anything lodged between it and the surrounding
Motor Frame Box. Also, make sure the Blades are able to spin freely and that there's no grass obstructing them.
IMPORTANT: Remove any lodged debris so that it does not cause a crack in the Blade Disc. Even the
tiniest crack can decrease your Landroid
C. Clean the contact pins and the charging strips
Clean the Contact Pins (3) located on the Charging Base (4) and the Charging Strip (5) located on the Landroid
cloth. Remove any build up of grass clippings and debris around the contact pins and charge strips periodically to ensure
®
the Landroid M successfully charges each time.
Lawn Mowing Robot
®
M's Blades
®
M does not like mowing
®
M.
®
M's Blades, turn the
®
M over.
®
M is an electric
®
M OFF using the ON/Off Button and wear protective gloves
®
M's mowing output.
®
M mows on a normal schedule (daily) then the Blades
L
®
M
M
13
®
M using a
EN