Table of Contents
Advertisement
Quick Links
AeroPet 50
AeroPet 50
0.52-0.70 cu.in.displacement 4-stroke
Requires: 5 channel radio w/ 5 standard servos
Wing Span
Wing Area
Flying Weight
Fuselage Length
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual
at hand for quick reference.
-
and 1 low profile retract servo
Specifications
* Specifications are subject to change without notice.*
55 in /1400 mm
576. 5 sq in / 37. 2 sq dm
5 lbs / 2280 g
57.5 in /1460 mm
ALMOST-READY-TO-FLY (ARF) SERIES
INSTRUCTION MANUAL
.
FACTORY PRE-FABRICATED
MADE IN CHINA
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for arf AeroPet 50
Summary of Contents for arf AeroPet 50
- Page 1 INSTRUCTION MANUAL AeroPet 50 AeroPet 50 0.52-0.70 cu.in.displacement 4-stroke Requires: 5 channel radio w/ 5 standard servos and 1 low profile retract servo Specifications 55 in /1400 mm Wing Span 576. 5 sq in / 37. 2 sq dm Wing Area...
-
Page 2: Before You Begin
AeroPet 50 AeroPet 50 I N D E X BEFORE YOU BEGIN P. 1 PARTS LIST P. 2 ASSEMBLY P. 3 - 10 SAFETY PRECAUTIONS P. 10 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. -
Page 3: Parts List
Parts List 1、MAIN WING--1 pair 13、 COWLING- - 1 pc. 2 WING TUBE Ø16x400mm--1 pc. TRANSPARENT DUMMY COWLING- -1 pc . 3、SCREW PB2x20mm--4 pcs SCREW PWA2. 6x12mm- - 4 pcs PUSHROD Ø1.8x115 mm w/Threads(For Aileron)--2 pcs SILICON GROMMET d1. 5xD6.5mm-- 4 pcs HORN--2 sets SPINNER Ø52mm- - 1 set CLEVIS--2 pcs... - Page 4 Main Wing A p p l y i n s t a n t t y p e C A g l u e t o b o t h s i d e s o f e a c h h i n g e .
-
Page 5: Aileron Servo
Aileron Servo Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PB2 x20mm Screw TWM PL8210010 CLEVIS WRENCH straper Fuel Tube D6X5mm PB2X20mm Pushrod Ø1.8x115mm Clevis Horn Bottom View Retractable Landing Gear Servo Adjuster Set Screw... - Page 6 Vertical Fin/Rudder Apply instant type CA glue to both sides of cach hinge. Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please Elevator Pushrod look for pin-hole marks at under side of control surfaces. PB2 x16mm Screw TWM PL8210010 CLEVIS WRENCH PB2x16mm Clevis...
-
Page 7: Fuel Tank
Tail Landing Gear PA3x12mm Screw 3mm Set Screw 2.1mm Collar 3mm Set Screw PA3x12mm Engine Mount M4 x25mm Socket Head Screw M4 x 25mm Washer 4.5x D9mm Engine Mount PL5111050 Washer d4 5x D9mm A p p l y t h r e a d l o c k e r t o s c r e w s Blind nuts are off-centered to keep the spinner at the fuselage axis. - Page 8 Engine M3.5x30mm Socket Head Screw M3.5 Nut d3 . 5xD8mm Washer M3.5 Nut Washer d3.5xD8mm Install Engine position Spinner Ø52mm Plastic tube d2xD3x250mm M3.5x30mm Throttle Pushwire 115mm Ø1. 2x410mm 5 in Cowling PWA2.6 x 12 mm Screw d1.5 x D6.5 mm Silicon Grommet First insert the grommet to the cowling then apply screw.
-
Page 9: Radio Equipment
Servo Set 3x3mm Set Screw LINKAGE CONNECTOR Set Screw 3 x 3mm Included with the radio Set. Linkage Connector Washer Washer Washer 2m m Throttle Servo. Please refer to attached sheet for linkage connector installation. Radio Equipment Elevator Push rod Ø1.8x100mm Press down the center M2 Nut... - Page 10 Canopy PWA2 3 x8mm Screw Pilot d1.5 x D6.5 mm Silicon Grommet Silicon Grommet d1.5xD6.5mm PWA2.3 x 8 mm Adjust the wing and fuselage configuration as shown Wing Setting in the diagrams. A A' B B' C C' P . 9...
- Page 11 #Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. AeroPet 50 AeroPet 50 is specially designed to be powered by 4c 0. 52- 0. 70 engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause severe damage and injuries.
- Page 12 LINKAGE CONNECTOR HW7111050 & HW7111060 Drill 2mm hole at servo horn. Insert linkage connector into servo horn. Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Shoulder Tighten up the round nut against the shoulder.
- Page 13 Product Registration Form (US Customers) We would like to share with you any relevant information regarding your model, including product news and free upgrade parts when applicable. Please fill in the following and send to AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA. 1.
- Page 14 180mm Extension Package Code No. Package Code No. Size Size Package Code No. Size Code No. Package Size Large Clevis Small Clevis Special tool for clevis installation. Suitable for standard and small Code No. Package ( EP) clevis. Size KP0041300 Code No SV4031 Package Code No.
- Page 15 The World Models Manufacturing Co., LTD. www .thew orldm odels .com A197PO21520908...
Need help?
Do you have a question about the AeroPet 50 and is the answer not in the manual?
Questions and answers