arf MINIMOA GLIDER Instruction Manual
  1. Manuals
  2. Brands
  3. arf Manuals
  4. Toy
  5. MINIMOA GLIDER
  6. Instruction manual

arf MINIMOA GLIDER Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SPECIFICATION
     Wingspan :
     Length
     Weight
     Radio
     Servo
     Mini servo :     02 Servos
Instruction Manual book
3,400 mm
:
1,465 mm
:
3,6 kg
Parts listing required (not included).
:
05 channels.
:
05 servos
133.86 in.
57.68 in.
7.92 Lbs.
Made in Vietnam.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MINIMOA GLIDER and is the answer not in the manual?

Questions and answers

Related Manuals for arf MINIMOA GLIDER

Summary of Contents for arf MINIMOA GLIDER

  • Page 1 Instruction Manual book SPECIFICATION      Wingspan : 3,400 mm 133.86 in.      Length 1,465 mm 57.68 in.      Weight 3,6 kg 7.92 Lbs. Parts listing required (not included). ...
  • Page 2 FUSELAGE ASSEMBLY aligned properly before gluing! This will assure  (1) Fuselage. proper assembly. ARF is hand made MINIMOA from natural materials, every plane is unique and minor adjustments may have to be made. WING ASSEMBLY However, you should find the fit superior and assembly simple.

  • Page 3: Safety Precaution

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. + Do not start the motor if people are SAFETY PRECAUTION. near. Do not stand in line with the side + This is not a toy of the propeller. + Be sure that no other flyers are using your + Make motor adjustments from behind radio frequency.

  • Page 4: Installing The Aileron Servos

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. I. AILERON. Bottom side. 1.INSTALLING THE AILERON SERVOS.   1) Install the rubber grommets and brass  2) Using a modeling knife, remove the cov- eyelets onto the aileron servos. ering at possition show below. Aileron ...

  • Page 5: Installing The Aileron Linkages

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. INSTALLING THE AILERON CONTROL HORN. Install aileron control horn as same as picture below. Control horn of Aileron Secure  5. Instal servo tray with aileron servo into the wing as same as picture below. Electric wire Epoxy PLUS glue.
  • Page 6 MINIMOA - INSTRUCTION MANUAL Item code: BH88.  6. Insert the 90 degree bend down through the hole in the servo arm. Install one nylon snap keeper over the wire to secure it to the arm. Install the servo arm retaining screw and remove the masking tape from the aileron.
  • Page 7 MINIMOA - INSTRUCTION MANUAL Item code: BH88. Bottom side 4x12mm INSTALLING ELECTRIC SPOILERS. NOT INCLUDED: Top side Remove covering Secure Bottom side...
  • Page 8 MINIMOA - INSTRUCTION MANUAL Item code: BH88. Secure. Repeat the procedure for the other wing half. INSTALLING ELECTRIC MOTOR. See pictures below: 3x15mm Drill a hole 3.8mm diameter.
  • Page 9 MINIMOA - INSTRUCTION MANUAL Item code: BH88. Secure. INSTALLING PROPELLER (NOT INCLUDED). Front view. Secure. Secure. ELEVATOR INSTALLATION. SERVO INSTALLATION.  1. Install the rubber grommets and brass collets into the elevator servo. Test fit the servo into the servo tray. ...

  • Page 10: Horizontal Stabilizer Installation

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. Temporary pin to Elevator keep hinge centered. servo. Assemble then apply drops of thin C/A to center of hinge,on both sides. HORIZONTAL STABILIZER INSTALLATION. Horizontal stabilize installation .  See picture below. Cut the covering away from the slot.

  • Page 11: Elevator Pushrod Installation

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. Secure Top side. Elevator control horn. Bottom side. ELEVATOR PUSHROD INSTALLATION.  Elevator pushrod install as same as the way of aileron pushrod. M2 lock nut. ELEVATOR CONTROL HORN INSTALLA- TION. Elevator control horn install as same as the way of aileron control horn.

  • Page 12: Vertical Installation

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. Elevator pushrod Cut. Secure. VERTICAL INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: Cut. bend 90 deagree. Cut the covering away from the slot.

  • Page 13: Rudder Control Horn Installa- Tion

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. Temporary pin to keep hinge centered. Assemble then apply drops of thin RUDDER CONTROL HORN INSTALLA- C/A to center of hinge,on both sides. TION. Rudder control horn install as same as the way of aileron control horn. Please see pic- tures below.
  • Page 14 MINIMOA - INSTRUCTION MANUAL Item code: BH88. Rudder Pushrod Rudder Pushrod Plastic parts of elevator pushrod and rudder pushrod.
  • Page 15 MINIMOA - INSTRUCTION MANUAL Item code: BH88. C/A glue Cut. C/A glue Bottom side. Cut.

  • Page 16: Wing Attachment

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. C/A glue INSTALLING THE RECEIVER AND BATTERY. WING ATTACHMENT.       1. Plug the servo leads and the switch Locate the aluminium wing dihedral brace. lead into the receiver. You may want to plug Aluminium tube 12 mm an aileron extension into the receiver to make...
  • Page 17 MINIMOA - INSTRUCTION MANUAL Item code: BH88. Right wing. INSTALLING THE COCKPIT. left wing.
  • Page 18 MINIMOA - INSTRUCTION MANUAL Item code: BH88. C/A glue Epoxy glue. Epoxy glue. See picture wing attach to fuselage. Installing the fuselage hatch as same as pic- ture below. C/A glue Top side. C/A glue...

  • Page 19: Control Throws

    MINIMOA - INSTRUCTION MANUAL Item code: BH88. BALANCING. CONTROL THROWS.       1) It is critical that your airplane be bal-       1) We highly recommend setting up a anced correctly. Improper balance will cause plane using the control throws listed.

Table of Contents