Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. For technical questions, please call 1-888-866-5797. Page 2 Item 61608...
Page 3
It’s safer than using your hand and it frees both hands to operate tool. 13. DON’T OVERREACH. Keep proper footing and balance at all times. For technical questions, please call 1-888-866-5797. Item 61608 Page 3...
Page 4
18. NEVER STAND ON TOOL. leave tool until it comes to a complete stop. Serious injury could occur if the tool is tipped or if the blade is unintentionally contacted. For technical questions, please call 1-888-866-5797. Page 4 Item 61608...
Page 5
9. Do not use an adapter to connect this tool to a different outlet. For technical questions, please call 1-888-866-5797. Item 61608 Page 5...
Page 6
• Push the wood stock past the an uncontrolled workpiece to lift up and blade prior to release. out of the saw toward the operator. For technical questions, please call 1-888-866-5797. Page 6 Item 61608...
Page 8
• Must be right (90°) angle, cut at 30°-40° from the angle 30°-40° of the stick to keep hands out of the line of the blade. • The lower lip of the notch must be no longer than the workpiece is thick. For technical questions, please call 1-888-866-5797. Page 8 Item 61608...
If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SAVE THESE INSTRUCTIONS. For technical questions, please call 1-888-866-5797. Item 61608 Page 9...
Figure A: Guard Installation NOTE: Make sure that the Eye Guard is on the top side of the guard and that the rounded underside of the Guard rests over the blade. For technical questions, please call 1-888-866-5797. Item 61608 Page 11...
3. For deepest cutting, allow the Table 7. When that desired depth is achieved, to rest fully on the Motor. tighten the Table Knob. 4. Tighten the Table Knob, and 8. After adjustment, check the Table′s stability. check the Table′s stability. For technical questions, please call 1-888-866-5797. Item 61608 Page 13...
Page 14
Table. If the work surface and workpiece supports are not level with each other, unwanted bevel angles will appear in the cuts and result in poor joinery. For technical questions, please call 1-888-866-5797. Page 14 Item 61608...
Guard in place. 6. Tighten the Guard′s Wing Nuts after every adjustment. Loose Wing Nuts may result in injury or damage to the tool. For technical questions, please call 1-888-866-5797. Item 61608 Page 15...
Switch off and unplug tool. b. Once Blade stops completely, remove Blade following instructions on page 13. For technical questions, please call 1-888-866-5797. Page 16 Item 61608...
See Table A on page 3. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. For technical questions, please call 1-888-866-5797. Item 61608 Page 17...
Note: If product has no serial number, record Note: Some parts are listed and shown month and year of purchase instead. for illustration purposes only, and are not available individually as replacement parts. For technical questions, please call 1-888-866-5797. Page 18 Item 61608...
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.