Risco gardtec 350+ User Instructions
  1. Manuals
  2. Brands
  3. Risco Manuals
  4. Control Panel
  5. GardTec 350+
  6. User instructions
Risco gardtec 350+ User Instructions

Risco gardtec 350+ User Instructions

Hide thumbs Also See for gardtec 350+:

Advertisement

Table of Contents

See also: Instruction and Installation Manual
G G
G G
3 3
5 5
0 0
+ +
C C
3 3
5 5
0 0
+ +
C C
User Instructions
This manual is found at www.eaglesecuritysolutions.co.uk
a a
r r
d d
T T
e e
c c
a a
r r
d d
T T
e e
c c
o o
n n
t t
r r
o o
l l
o o
n n
t t
r r
o o
l l
P P
a a
n n
e e
l l
P P
a a
n n
e e
l l

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the gardtec 350+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Risco gardtec 350+

Summary of Contents for Risco gardtec 350+

  • Page 1 User Instructions This manual is found at www.eaglesecuritysolutions.co.uk...

  • Page 2: Table Of Contents

    Users Manual GARDTEC 350 Contents Introduction Setting the System Part Setting the System Unsetting the System Resetting after an Alarm User Programming Mode Removing Individual Zones Testing the System Reading the Log Turning Chime On and Off Programming User Codes Care and Service of Your System Terminology Installers Details...

  • Page 3: Introduction

    Users Manual GARDTEC 350 GARDTEC 350 USER INSTRUCTIONS INTRODUCTION Your Gardtec 350 Control Panel will have been fully programmed by your installation engineer to suit your needs. Normal day to day operations will consist of the following:- Fully setting the system Part setting the system Unsetting the system Display is given via eight individual L.E.Ds.

  • Page 4: Setting The System

    Users Manual GARDTEC 350 SETTING THE SYSTEM To Fully Set the system proceed as follows:- Enter a valid User code. (The DAY LED will flash followed by the exit tone. Any zones violated during exit will change the exit tone and the appropriate L.E.D will indicate). Leave the premises via the authorised exit route.

  • Page 5: Unsetting The System

    Users Manual GARDTEC 350 UNSETTING THE SYSTEM To Unset the system proceed as follows:- Enter the premises via an authorised entry point (the entry tone will sound). Proceed directly to the Control Panel and enter a valid User code (the entry tone will stop and the DAY LED will illuminate).
  • Page 6 Users Manual GARDTEC 350 The User programmable options are as follows:- R R e e m m o o v v e e This option enables the Master user to Remove individual zones when setting the sys- tem. This is in addition to any part set suites pre-programmed by your engineer. T T e e s s t t This option allows the Master user to Test the system.

  • Page 7: Removing Individual Zones

    Users Manual GARDTEC 350 REMOVING INDIVIDUAL ZONES With the Control panel in the DAY mode (Unset) enter the Master code. The exit tone will sound. Before the exit time expires Press NO. The exit tone will silence and the R R e e m m o o v v e e LED will flash as shown in Fig 4.
  • Page 8 Users Manual GARDTEC 350 Press the key corresponding to the zone you wish to remove followed by the YES key (a comfort tone will be generated if all is okay). If you make a mis- take and remove the wrong zone repeat the operation from step 3 but press NO after the zone number.

  • Page 9: Testing The System

    Users Manual GARDTEC 350 TESTING THE SYSTEM With the Control panel in the DAY mode (Unset) enter the Master code. The exit tone will sound. Before the exit time expires Press NO. The exit tone will silence and the R R e e m m o o v v e e LED will flash.

  • Page 10: Reading The Log

    Users Manual GARDTEC 350 The Gardtec 350 has a 50 event Log that records system events in the order that they occur. To view the Log proceed as follows:- With the Control panel in the DAY mode (Unset) enter the Master code. The exit tone will sound.

  • Page 11: Turning Chime On And Off

    Users Manual GARDTEC 350 CHIME The Chime function may be turned On or Off by the Master user. Before Chime can be turned on the Chime zones should have been programmed by your engineer. To turn the Chime On or Off proceed as follows:- With the Control panel in the DAY mode (Unset) enter the Master code.
  • Page 12 Users Manual GARDTEC 350 USER CODES When programming User Codes you should note the following:- User 1 is always the Master Code. This level of code allows you to perform all User functions (including resetting after an alarm) and all User Programming functions.

  • Page 13: Programming User Codes

    Users Manual GARDTEC 350 Press YES to use the P P r r o o g g r r a a m m (C C o o d d e e ) option. The display will show as Fig 11 Fig 11.
  • Page 14 Users Manual GARDTEC 350 Press YES to use the P P r r o o g g r r a a m m (C C o o d d e e ) option. The display will show as Fig 11 Fig 11.

  • Page 15: Care And Service Of Your System

    Users Manual GARDTEC 350 CARE AND SERVICE OF YOUR SYSTEM User care of the system consists of occasionally wiping the control panel. Under no circumstances should detergents or abrasives be used. Opening the control panel or detectors will generate a tamper alarm and service should be carried out by a qualified alarm engineer.

  • Page 16: Installers Details

    Users Manual GARDTEC 350 INSTALLATION DETAILS Company Name:- Company Address:- Company Tel No:- Service Tel No:- First Service Due Date:- SERVICE RECORD Service No Due Date Actual Date Engineers Sig Page...
  • Page 17 User Manual GARDTEC 350 Notes...
  • Page 18 User Manual GARDTEC 350 Notes...
  • Page 19 User Manual GARDTEC 350 Notes...
  • Page 20 Tel: 0161 655 5500 Fax: 0161 655 5501 Internet: www.riscogroup.com e-mail: sales@riscogroup.co.uk Technical Support: 0161 655 5600 Technical Support Fax: 0161 655 5610 RISCO Group UK Ltd reserve the right to amend the software and features without prior notice PR2897 REV2.3 This manual is found at www.eaglesecuritysolutions.co.uk...

Table of Contents