Maximum Controls Max Megatron 1400 Installation And Owner's Manual page 20

Motor
OverLoad
ERD
Inputs & MUST be "LEARNED" to MONITOR OPENING/CLOSING direction sensors.
2 3
To LEARN inputs & :
1. MONITORED Sensors MUST be wired to inputs BEFORE they can be learned.
Any unused inputs MUST be jumpered, see previous page.
2. A Sensing Edge or Photo Cell can be wired to either input 2 or 3.
3. Press and HOLD the STOP button & then the OPEN button
together on Matrix 1 until beep is heard, learn mode begins.
NOTE: DO NOT press the OPEN button before the
STOP button or learn mode will NOT function.
4. LEDs WILL be ON for each detected sensor on MC-200.
LEDs WILL be ON for BOTH MC-200s when dual operators Motor
OverLoad
are used. If an LED is not on and it should be, wiring to
ERD
sensor is bad, photocells are out of alignment, photocells
are wired wrong - N.C. or N.O. depending on which
photocells are used (see below) or sensor is bad etc. and
must be corrected. When all LEDs are ON that should be ON, proceed to next step.
5. Press STOP button again within 5 min. to learn sensors and
end learn mode, beeping stops.
Wired Inputs are now MONITORED.
If STOP button is not pressed within 5 min. learn mode terminates.
If no sensors are detected then factory default setting (Edge 2 and
UL 325 2016 Compliant MONITORED Normally Closed Entrapment Protection Devices:
Normally Closed Definition: When Power is off, relay contacts are OPEN. When Power is on, relay contacts are CLOSED.
Photo Cells:
Model RG Miller Edge Reflecti-GUARD Reflective-Beam Type (Normally Closed)
Model PG Miller Edge Prime-GUARD Thru-Beam Type with battery operated transmitter (Normally Closed)
Model EMX-IRB-MON EMX Thru-Beam Type (Normally Closed)
Model EMX-IRB-RET EMX Reflective-Beam Type
Model E3K-R10K4-NR OMRON Photo Electric Sensor Reflective-Beam Type
Model 60-2728-1 Allen Bradley Reflective-Beam Type
Direct-wired 10K Sensing Edge:
Model 10K Sensing Edge with GEM-104 Module Miller Edge (Normally Closed)
MAX 10K Mini Edge Maximum Controls (Normally Closed) Requires a Miller Edge GEM-104 module
MAX 10K Edge 1 Maximum Controls (Normally Closed) Requires a Miller Edge GEM-104 module
Sensing Edge Wireless Transmitter/Receiver:
Model MGL-K20 Miller Edge Monitored Gate Link Transmitter and Receiver
18
Wiring operator
ERD
JOG
Sensitivity
LEFT
RIGHT
5
4
3
MAX
12
16 LED ON
13 15
14
2 3
ERD
JOG JOG
Sensitivity
LEFT RIGHT
5
4
3
MAX
12
16 LED ON
13 15
14
(MUST be wired to Normally Open)
JOG
ON-LINE
2 3
1
Limit SW
MOTOR MOTION
OPEN STOP
MATRIX
ON-LINE
Edge UL Entrap
1 1 1
1 2 3
2 2 2 2 2 2 2 2 2
Edge Edge Edge Edge Edge Edge Edge Edge Edge P PhotoCell P P P PhotoCell P P P P P P PhotoCel P hotoCell hotoCe hotoCel hotoCell
Limit SW
MOTOR MOTION
OPEN
(MUST be wired to Normally Open)
(MUST be wired to Normally Open)
MC-200
Motor Controller
MATRIX
Edge UL Entrap
1
POWER
2
Edge PhotoCell
EDGE 1 Note: CLOSING direction ONLY.
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
MADE in USA LEAVE
OPEN
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
TAILGATE EXIT
EXIT
ON OFF
CENTER
SAFETY SAFETY
MIN MIN MAX MAX
OFF OFF
CLOSE TIMER CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
CLOSE
POSITION
RECORDER RECORDER
12VDC 12VDC
GND GND OBD PORT OBD PORT
BLACK BOX
24VDC
GND
MC-200
Motor Controller
Example shows that sensors
POWER P P P
are DETECTED on inputs
Edge 2 and Photo Cell.
otoCe otoC otoCe
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
MADE in USA LEAVE
OPEN
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
TAILGATE EXIT
EXIT
ON OFF
CENTER CENTER
SAFETY SAFETY
MIN MIN MAX MAX
OFF OFF
STOP
CLOSE TIMER E TIMER
CLOSE
PARTIAL
OPEN
ID
PLUG
POSITION POSITION
RECORDER CORDER
12VDC
GND OBD PORT
BLACK BOX
24VDC
GND
will work with 12V
PRIMARY
GATE
MAGLOCK
DELAY
OPEN OPEN
OPEN MAG
1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
GATE
CENTER SAFETY
COM
TAMPER
GND
Tamper IN
PHOTOCELL
UL EDGE 1
ENTRAP EDGE 2
ID PLUG
MOTOR MOTION
ERROR
UL ALARM 12V
ALARM RET
RESET
OPEN STOP CLOSE
GND
MAX MAX REVERSE SENSITIVITY REVERSE SENSITIVITY
GA GATE SPEED
MOTOR OVERLOAD
GATE OPEN
MIN
NO LIMIT SWITCH /
STATUS COM
CLAMP SLIPPING
MAX
CLOSE
LIMIT BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
ON-LINE POWER
PRIMARY SEC
GATE GATE
PRIMARY
GATE
MAGLOCK
DELAY
OPEN OPEN
OPEN MAG
1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
GATE
CENTER SAFETY
COM
TAMPER
GND
Tamper IN
PHOTOCELL
UL EDGE 1
ENTRAP EDGE 2
ID PLUG
MOTOR MOTION
ERROR
UL ALARM 12V
ALARM RET
RESET
OPEN STOP CLOSE
GND
MAX REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
GATE OPEN
MIN
NO LIMIT SWITCH /
STATUS COM
CLAMP SLIPPING
MAX
CLOSE
LIMIT BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
ON-LINE POWER
PRIMARY SEC
GATE GATE