Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DAITEM SH148AX
Summary of Contents for DAITEM SH148AX
-
Page 2: Table Of Contents
The user must not attempt to access the detector’s internal parts, except areas described in this manual. If the user does access these parts, the product guarantee will be considered null and void and DAITEM shall not be held responsible for any problems. Touching the detector’s internal parts and/or electronic components can damage the product. -
Page 3: Preparation
(screws not Radio box N.B. The product is delivered unscrewed. supplied) 1 screw to be positioned on the snap-off part to ensure protection against removal SH148AX Coller sur certif Radio card A1142A047879 (screw not supplied). SH148AX Coller sur certif A1142A047879... -
Page 4: Power Supply
If the self-test is satisfactory, the programming indicator lights up for roughly 2 s. Lower lens Inside view of radio box Front panel Programming LED Guarantee sticker SH148AX Coller sur certif A1142A047879 SH148AX Coller sur certif A1142A047879 Unlocking tab Sticker listing... -
Page 5: Recognition Programming
3. Recognition programming IMPORTANT • The device does not need to be placed close to the control panel for recognition programming. In fact, we advise you to move the product at least 2 metres away from the control panel. • The detector n° is allocated automatically by the control panel during recognition programming. This operation allows the control panel to recognise the detector. -
Page 6: Parameter-Setting
4. Parameter-setting Parameter-setting sequence Parameter N° Alarm level Parameter value Intrusion Prealarm Deterrence 3 (factory setting) The motion detector is factory-configured 4 (function compatible with control panel Warning for deterrence (see your control panel versions 2.0.0 and later) installation guide for system responses). The alarm level can be changed by resetting the parameters as shown opposite. -
Page 7: Installation Precautions
5. Installation precautions IMPORTANT: make sure each product is at least two metres away from other devices, except other detectors. The detector must be placed: • perpendicular to the • facing a moving object (branches, bushes, • at a height of 0.8 to 1.2 m, ground so that the curtains, etc.), upper detection... -
Page 8: Installing The Detector
6. Installing the detector 6.1 Testing the radio link 6.2 Fixing the detector in place IMPORTANT: the control panel must be in 1. Fix the base to the wall using suitable 2. Position the 2 screw covers on the installation mode to perform this test. wall plugs and screws (i.e. -
Page 9: Detection Settings And Configuration
7. Detection settings and configuration 7.1 Detection range The detector’s overall range is determined by • The lower lens is factory-positioned for • The detection range is determined by the the lower beam range. detection at 5 m. If 2 m detection is lower lens setting and the detector •... -
Page 10: Adjusting The Detection Angle Horizontally
7.2 Adjusting the detection angle horizontally To set the detection zone: 1. Remove the locking 3. For protection along a vertical surface (wall, bay window, etc.), it is advisable mechanism using a to align the detection zone parallel with this surface: flat-headed •... -
Page 11: Setting The Operating Options
7.3 Setting the operating options The options are set using the 6 dip switches inside the detection module. Detector in test mode The LED lights up each time something is detected making it possible to test the range. 1 2 3 4 5 6 Detector in normal user mode (factory setting) The LED remains unlit (unless dip switch n°... -
Page 12: Anti-Masking Function
7.4 Anti-masking function The function is operational if: • the option has been validated (dip switch n°4 ON) • the product is fixed to the wall and its front panel is closed. When the above both apply, there are three phases: 1. -
Page 13: Testing Operation
8.1 Testing the detection zone Detected Not detected installer code IMPORTANT: It is normal for the LED indicator to light up only 2 or 3 seconds later during the detection zone test. Zone A: detection range (determined by the lower lens position and the installation height). -
Page 14: Maintenance
(3.6 V - 4 Ah). • We advise you to use a DAITEM brand BatLi25 battery available in the catalogue in order • Radio fault: following a system command, to guarantee individual safety and equipment reliability. -
Page 15: Technical Data
SH148AX Technical specifications Product type: Outdoor IR anti-masking 5 m detector Trade mark: Daitem Outdoor IR anti-masking 5 m detector We declare under our sole responsibility that the products to which this declaration relates are thus compliant with the essential requirements of the following European...
Need help?
Do you have a question about the SH148AX and is the answer not in the manual?
Questions and answers