Page 1
5.6" Multifunction Monitor 5.6" Multi-function Monitor User’s Manual Please read this Manual carefully before use of this product, and keep it handy for future reference.
Page 2
5.6" Multifunction Monitor I. Packing List ……………………………………………….. 2 II. Product Appearance………………………………………... 3-5 III. Product Operation………………………………………….. 6-8 IV. Screen Display……………………………………………... 9-10 V. List of Supported Display Modes………………………….. 11 VI. Technical Parameters………………………………………. 12 VII. Troubleshooting………………………………………….13...
Page 3
5.6" Multifunction Monitor 5.6" multifunction monitor × 1 pc Sun visor × 1 pc Power adapter × 1pc Rechargeable Lithium Battery ×1pc 12V power output cable ×1pc User’s Manual × 1 pc...
Page 4
5.6" Multifunction Monitor Front View 5.6 " LCD panel (adopting tempered glass cover). LED indicator. MEMU Key: The main menu key, acting as the Enter Key during menu operation. SOURCE Key: With the function of signal channel switching, acting as the Left Selection Key during menu operation.
Page 5
5.6" Multifunction Monitor Left Side View Rear View AHD Input Interface TVI Input Interface Audio Input Interface DC12V --1A Output Interface Power switch. The product can work properly only when the switch is turned “ON”. VGA signal input interface. HDMI signal input interface.
Page 6
5.6" Multifunction Monitor Right Side View Top View Picture brightness adjusting knob: turn it upwards to increase the brightness, and turn it downwards to decrease the brightness. Picture contrast adjusting knob: turn it upwards to increase the contrast, and turn it downwards to decrease the contrast.
Page 7
5.6" Multifunction Monitor Step 1: Turn the power switch “ON”, the LED indicator stays on in green and the device is working properly. Step 2: According to the current signal access mode, press “SOURCE” on the right side panel select corresponding signal channel.
Page 8
5.6" Multifunction Monitor Charge and Discharge Connect the DC12V-1500mA charger from the accessories according to the figure shown, and connect to the AC power. Battery Test Having plugged into the power supply, it comes into charging status when LED light indicates red; The battery is fully charged when the LED light indicates green, It indicates that the battery is abnormal or no battery available when the LED indicator flashes red.
Page 9
5.6" Multifunction Monitor Information Display on the Screen Battery charging icon. Information of signal channel . Resolution. Battery level icon.
Page 10
5.6" Multifunction Monitor Signal Selection Menu Operation method: Press the “SOURCE” key, and the signal channel selection interface will appear on the screen as shown in the figure on the left. Press the “SOURCE” key again, and the yellow cursor will move down to the next signal channel;...
Page 11
5.6" Multifunction Monitor Main Menu (Settings) Operation method: Press the “MENU” key, and the main menu interface will appear on the screen as shown in the figure on the left. Press the “SOURCE” key and “P/G” key to select submenus leftwards and rightwards;...
Page 13
5.6" Multifunction Monitor Product name 5.6 inch HD LCD Monitor Display area 112.896 (H) ×84.672 (V) mm Display ratio Backlight Resolution 640×480 LCD panel Brightness 200cd/㎡ Contrast ratio 500:1 Response time 10ms Dot pitch 0.0588 (H) ×0.1764 (V) mm Viewing angle Top/bottom/left/right: 70°/50°/70°/70°...
Page 14
5.6" Multifunction Monitor Before asking for maintenance, please check the information in this section to see if the problem can be solved by yourself; if necessary, please contact our After-sales Service Center or the distributor. Problem Possible cause Solution Recharge the battery or install a fully charged The battery is used up.
Need help?
Do you have a question about the VZ56SM and is the answer not in the manual?
Questions and answers