ViewZ VZ-UNBS SERIES User Manual
49" and 55" professional
led cctv video wall monitor
Hide thumbs
Also See for VZ-UNBS SERIES:
- Installation & handling manual (4 pages) ,
- User manual (8 pages)
Subscribe to Our Youtube Channel
Related Manuals for ViewZ VZ-UNBS SERIES
Summary of Contents for ViewZ VZ-UNBS SERIES
- Page 1 VZ-UNBS SERIES 49" and 55" PROFESSIONAL LED CCTV VIDEO WALL MONITOR USER MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
-
Page 2: Table Of Contents
1. Remote Control Function ................................2. Daisy Chain Configuration ................................3. OSD Control and Function ................................Mounting Guide ......................................RS232 (RJ-45) Pin Map ....................................Specification ........................................Trouble Shooting ................................................................................Warranty ........................................Visit the ViewZ USA website at https://www.viewzusa.com User Manual... -
Page 3: Safety Instruction
The monitor shall not be exposed to dripping or splashing and objects containing liquids such as vases shall be placed near the monitor. The monitor should have ample distance (e.g. 10cm) from the wall for sufficient ventilation. User Manual Visit the ViewZ USA website at https://www.viewzusa.com... -
Page 4: Mark Indication & Substance
If your monitor does not operate normally – in particular, if there is any unusual sound or smell coming from the monitor – unplug it immediately and contact an authorized dealer or the service center. Visit the ViewZ USA website at https://www.viewzusa.com User Manual... - Page 5 While most pixel faults occur in isolated regions, a cluster of dead pixels or sub-pixels can sometimes form for which a separate ruling applies. A cluster is defined as an area of 5x5 pixels. ViewZ’s policy on pixel failure: either as an isolated fault or in the form of a cluster is outlined on the website: www.viewzusa.com User Manual Visit the ViewZ USA website at https://www.viewzusa.com...
-
Page 6: Fcc Rf Interference Statement
If some company or product trademark is not particularly stated, the use of trademark has been fully recognized. Do not alter, decompile, disassemble, decode or conduct reverse engineering to the software installed in the product, or it can be deemed as breach of the law. Visit the ViewZ USA website at https://www.viewzusa.com User Manual... -
Page 7: Installation
Automatic Screwdriver Phillips & Flathead Screwdriver Bit Assembly Components - provided Your ViewZ monitor is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399. -
Page 8: Features
Before operating the video wall monitor, please make sure you fully understand relevant prerequisites such as the specification or limitation of H/W and S/W. ViewZ shall not be responsible for loss, damage or injury caused by improper use of products. -
Page 9: Interface Resolution & Refresh Rate
Interface Input Source Max Resolution Refresh Rate Display Port 3840 x 2160 30Hz HDMI (2.0) In / Out 3840 x 2160 60Hz DVI-D In 3840 x 2160 30Hz 1920 x 1080 60Hz User Manual Visit the ViewZ USA website at https://www.viewzusa.com... -
Page 10: Function
5. Press the 'ENTER' button to confirm / the 'MENU/EXIT' button to exit for saving adjustment value on sub-menu. 6. Press the 'MUTE' button to on / off audio-out of monitor. Visit the ViewZ USA website at https://www.viewzusa.com User Manual... -
Page 11: Daisy Chain Configuration
, according to this wiring, as shown above as shown, the upper left corner is the screen , the upper right corner is the screen , the lower left corner is the screen , and the lower right corner is the screen User Manual Visit the ViewZ USA website at https://www.viewzusa.com... -
Page 12: Osd Control And Function
Press ▲ / ▼ button to change input source and then press ENTER button to select input source on remote controller. If you connect any input source, monitor will display current input source resolution and frequency. Visit the ViewZ USA website at https://www.viewzusa.com User Manual... - Page 13 Give the white color a neutral tint 9000K Give the white color a blue-ish tint 0 ~ 255 USER 1 & 2 Apply user selected values - Red, Green & Blue User Manual Visit the ViewZ USA website at https://www.viewzusa.com...
- Page 14 Adjust the vertical noise of screen image Press ENTER button on remote controller to set AUTO ADJUST Adjust the screen automatically auto adjust for screen 1) Only available in VGA input Visit the ViewZ USA website at https://www.viewzusa.com User Manual...
- Page 15 ► To apply each monitor as one of the video wall system monitors, you should click 'Video Wall Set' after the setup of 'Wall H/V End' ► To apply all of video wall system monitors, you should apply 1) ~ 4) process to each monitor User Manual Visit the ViewZ USA website at https://www.viewzusa.com...
- Page 16 5) Click 'Application' to be applied typed values. Then, click 'Close OSD' ► After this process, if you open the 'ID' OSD window, it will show default value. But, the values (for HDCP input) is already set it up Visit the ViewZ USA website at https://www.viewzusa.com User Manual...
- Page 17 SOFTWARE UPDATE Update the monitor firmware by default YES/NO EDID SWITCH Change EDID version for HDCP Input 1.4/ 2.0 EDID 1.4 1) You can use USB drive to upgrade firmware of monitor. User Manual Visit the ViewZ USA website at https://www.viewzusa.com...
-
Page 18: Mounting Guide
Please use bolt of correct size and length as instructed. Mounting Safety ! At least two people are recommended to safely install the mount and monitor. Visit the ViewZ USA website at https://www.viewzusa.com User Manual... -
Page 19: Rs232 (Rj-45) Pin Map
If your video wall system requires an unified control by the central control (do not use provided video wall screen control software), please use the provided RJ-45(RS-232) cables to configure the sytem. If necessary, you can make your own RJ-45(RS-232) cables based on the above pin map. If you have further questions, please contact ViewZ. Firmware Upgrade/Update Process 1. -
Page 20: Specification
Accessories AC110V Power Cable x 1, HDMI Cable x 1, Manual x1, CAT5 Cable (RS232) x 1, Remote Controller x 1, IR Receiver x 1, Converter (RJ45 to RS232) x 1 Visit the ViewZ USA website at https://www.viewzusa.com User Manual... -
Page 21: Trouble Shooting
At start input source. If symptom persists, follow the instructions below. After following the instructions below, please contact us at 1-888-99-VIEWZ. - Make sure the cable is correctly plugged into the outlet. - Make sure the power cable is correctly plugged into the monitor. -
Page 22: Rma
Failure by limited life of parts such as LED lamps and any other consumables. Damaged by using third party power cable, unstable power input and electric shock. * Above information can be changed without notification - please check our website or contact ViewZ representative for the latest RMA service policy. - Page 23 NOTE User Manual Visit the ViewZ USA website at https://www.viewzusa.com...
-
Page 24: Warranty
What and Who is Covered by this Limited Warranty and for How Long ViewZ USA warrants this product to be free from defects in material and workmanship for 3 years to the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
Need help?
Do you have a question about the VZ-UNBS SERIES and is the answer not in the manual?
Questions and answers