Clock And Timer; Basic Operation; Tuner Operation - Goodmans MICRO 1465i User Manual

CLOCK AND TIMER

Current time setting
When used for the first time, or if the mains plug has been removed for any time,
the clock display will flash "AM 12:00"
1. In standby mode, press the PROG/CLK ADJ button (6/38) the hour digits will
flash in the display.
2. Press SLEEP/12/24HR (34) button to change 12hour or 24hour time format.
3. Press /TUNING or
repeatedly to select the correct hour.
4. Press the PROG / CLK ADJ (6, 38) button again, then press
/TUNING or /TUNING
select the correct minute.
5. Press PROG / CLK ADJ (6, 38) button again to complete setting the current
time.
TIMER ON and OFF setting (Automatically turn on and off the unit)
1. In standby mode, press the MODE/REMAIN (40) button. "TMR-ON"
indicates and " " flashes in the display. Press the PROG / CLK ADJ (6, 38)
button and the hour digit will flash.
2. Press the /TUNING or
repeatedly to set the desired hour. For example "2:00".
3. Press the PROG / CLK ADJ (6, 38) button and the minute digit will flash.
4. Press the /TUNING or
repeatedly set to the desired minute. For example "2.08"
5. Press the PROG / CLK ADJ (6, 38) button again to confirm the setting.
6. Press the MODE/REMAIN (40) button again. "TMR-OFF" indicates and " "
will flash in the display. Press the PROG / CLK ADJ (6, 38) button and the
hour digit will flash.
7. Press the /TUNING or
repeatedly to set the desired hour. For example "4:00".
8. Press the PROG / CLK ADJ (6, 38) button again and the minutes digit will
flash.
9. Press the /TUNING or
repeatedly set to the desired minute. For example "4.08".
10. Press the PROG / CLK ADJ (6, 38) button again to confirm the setting.
11. Press the MODE/REMAIN (40) button to return the display to the current
time.
12. Press the TIMER (37) button until " " indicates in the Display. The unit will
automatically turn on and off at the appropriate time.
13. Press the TIMER (37) button again until " " disappears and the timer
function will be cancelled.
Note:
- Please ensure the correct time is set before setting the Timer on/off function.
- The On/Off timer can only operate if the unit is switched to standby mode when not in use. In timer
mode, the unit will switch on in the last mode that was in use.
If you wish to wake to music from your
If you wish to wake to music from a CD, ensure that a CD is loaded.
If you wish to wake to radio, ensure that a radio station is tuned.
If you wish to wake to music from USB or SD/MMC, please ensure that a USB device or SD/MMC card
is inserted.
/TUNING (20, 35) button
(20, 35) button repeatedly to
/TUNING (20, 35) buttons
/TUNING (20, 35) buttons
/TUNING (20, 35) buttons
/TUNING (20, 35) buttons
, ensure that the is connected.
- 8 -
SLEEP setting (Automatically turn off)
The unit can be programmed to switch off after a set time during use, for example
if you wish to go to sleep whilst listening.
The Sleep time can be set at 10, 20, 30, 40, 50, 60, 70, 80 or 90 minutes.
Press the SLEEP/12/24HR button repeatedly until the desired sleep time is shown
in the display.
The unit will automatically switch off at the selected sleep time.
Note: If the CD playing time is shorter than your selected sleep time, the music will stop at the end of
disc.

BASIC OPERATION

Turn on the unit
Press the STANDBY (5, 30) button to turn on or turn off the unit.
Operating mode selection
Press the TUNER/BAND (7, 45) button,
button to select the different operating modes.
PLAY / PAUSE / PRESET- (14, 47) button:
Press this button to begin playback or pause a CD. In Tuner mode, press this button to skip to a
previous preset radio station.
STOP / PRESET+ (15, 32) button:
Press this button to stop the playback of a CD. In Tuner mode, press this button to skip to the next
preset radio station.
VOLUME (18, 48) button:
Press repeatedly to adjust sound level output from 00 (minimum) to 40
(maximum).
MUTE (44) button:
Press this button to mute the sound output from the unit "VOL-OFF" will show in
the display. To restore sound output, press the button again "VOL-ON" will show
in the display.
EQ (19, 50) button:
Press this button to select one of the 5 preset sound equaliser settings. These are
FLAT, ROCK, JAZZ, POP and CLASSIC.

TUNER OPERATION

Manual operation
1. Press the STANDBY (5, 30) button to turn on the unit
2. Press TUNER/BAND button repeatedly to select MW or FM.
3. Press / TUNING or
manually tune up or down the current waveband in 0.05MHz increments.
Automatic search operation
1. Press and hold the / TUNING
automatically search for the next or previous radio station with a strong signal. Stations with a
weak signal can be tuned manually.
2. Press and hold / TUNING
second, to start the station search again.
Note: During the search operation the sound level will be muted automatically.
(8, 31) button, CD/USB/SD (9, 46) button or AUX (43)
/ TUNING (20, 35) buttons to
or / TUNING (20, 35) buttons to
or / TUNING (20, 35) button approx 1
- 9 -