Page 2
FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
4. The WebEye is made of aluminum. Be sure that it is fastened tightly during installation to avoid any human injuries. Make sure to place away from the reach of children. 5. If WebEye does not operate properly, please contact your WebGate distributor for after sales service. Unauthorized personnel are prohibited from disassembling the product. Disassembly will automatically result in void of service warranty.
4.2. System requirements of PC ..................11 4.3. Installig program ......................12 Connecting & Running ...................... 15 5.1. Connecting WebEye 2.0 B101 to Network ..............15 5.1.1. Connecting to PC directly ..................15 5.1.2. Connecting to local Network.................. 16 5.2.
Introduction 1. What is WebEye 2.0 B101? WebEye 2.0 B101 is a network video server solution with an integrated Internet server, image comp ression device, flash memory, and many other features. No other hardware is necessary for use. It relays video source from a CCTV camera to network and provides real time images over networks and the Internet.
3.1. Using tapping screw This is how to attach WebEye 2.0 B101 to wall or ceiling. TAPPING SCREW 1) Make a hole (diameter: Φ6.5, depth: 30mm or above) 2) Insert the supplied plastic anchor into the hole. PLASTIC ANCHOR 3) Fix WebEye 2.0 B101 with tapping screw.
4. Installing & Connecting 4.1. Installing WebEye 2.0 setup program Within the supplied CD-ROM DISC, there are “WebEye 2.0 B101 User’s Guide” and WebEye 2.0 setup programs for using WebEye B101 2.0. 4.2. System requirements of PC Minimal Recommended Intel Pentium III 600Mhz Intel Pentium IV 1.6Ghz or above...
4.3. Installig program (1) Run “WebEye 2 Setup v.1.x.x.x.exe” file in WebEye 2.0 Seup CD. (2) Select a language and click the “OK” button. (3) Press the “I Agree” button. (4) In order to use all functions of WebEye 2.0, select “WebEye Controllers”, “WebEye Utills”, and “WESP SDK”...
Page 13
WebEye Controllers To istall necessary program for aeecssing WebEye 2.0 and monitoring its image. WebEye Utils To install WebEye2 Configuration Tool (Setting), WebEye2 MiniPlayer (Replaying the quick recorded file), and WebEye2 OnetimePW (Creating one time password). WESP SDK To install WESP library file that is used in WebEye 2.0. (5) Select a folder to install and press the “Install”...
Page 14
(6) Complete to install with pressing the “Close” button. Check whether all three programs are installed. - WebEye 2 Configuration Tool - WebEye 2 MiniPlayer - WebEye 2 OnetimePW...
5. Connecting & Running 5.1. Connecting WebEye 2.0 B101 to Network Connect WebEye 2.0 B101 to PC directly with cross cable or connect WebEye 2.0 B101 to local Network with direct cable. 5.1.1. Connecting to PC directly (1) Connect WebEye 2.0 B101 to client’s PC with cross cable.
(SUPPLIED) TO AC OUTLET <Note> 1. To prevent WebEye 2.0 B101’s damage, you should connect power cable after connecting Ethernet cable. 2. Ethernet cable should be pushed and connected, If not, noise may be occurred. 3. Check the LED of WebEye 2.0 B101 after supplying power.
5.2. Changing IP address & Login After connecting WebEye 2.0 B101 to Network, its IP address should be changed according to each Network environment to access WebEye 2.0 B101 normally. (1) Run WebEye 2. Configuration Tool in PC. (2) Every WebEye 2.0, which is connected to local Network, is displayed in “Local Area Units”.
2. When using cable modem or xDSL (automatic access modem), set it as “Ethernet” type. 5.3.2. When connected to xDSL When WebEye 2.0 B101 is connected to xDSL line, set as follows then connect to xDSL line. (1) Select “xDSL” type in “Network” tab.
If WebEye 2.0 B101 is installed on a network of dynamic IP address (floating IP address), administrator should register the WebEye 2.0 B101 on dynamic IP registration server to give common users simple connectivity. If not, no one can access the WebEye 2.0 B101 through Web browser. It is because that no...
Page 20
IP address which one can access the WebEye 2.0 B101 with. To solve the problem, WebGate runs WRS(Dynamic IP Registration Sever). (1) Select a registration interval. (1 minute~24 hours) (2) Enter server address. (default value : 210.116.114.37) (3) Enter access token.
5.4. Setting video It is to set video input channel. (1) Select video channel to set. (2) Check “Enable”. (3) Select video type (NTSC/PAL). (If video type is changed, WebEye should be rebooted.) (4) When camera is installed reversely, check “Rotation 180’. (5) Select image quality.
5.5. Changing admin password & Registering user Administrator’s ID is fixed as “admin”, and the default admin password of WebEye 2.0 B101 is “admin”. The ID can’t be changed, but only password can be changed. (1) Press the “Change” button.
5.6. Viewing image via browser After setting Network and Video tabs, image of WebEye can be viewed via web browser. (1) Run web browser at PC. (2) Enter IP address of WebEye 2.0 to access. (3) If WebEye is accessed, login page will show. (4) Enter user ID and password, and clicking the “Login”...
Page 24
When accessinf WebEye 2.0 web page for the first time without installing WebEye Setup v1.2.x.x.exe file, an installation message for certifying and running image will be shown at login step. For using WebEYe 2.0 B101 normally, the control program should be installed.
6. Using Input / Output The electrical diagram of WebEye 2.0 B101 is as below. <Note> Trimming Wire When connecting a wire to a terminal block, follow the instructions below. Note the different types of wire that can be used. (1) is recommended.
6.1. Connectinsg power When supplying power to WebEye 2.0 B101, you should certainly do that after connecting WebEye 2.0 B101 to power cable to WebEye 2.0 B101. Don’t connect power cable to WebEye B101 with supplied power. 6.1.1. Connecting DC power 6.1.1.1.
6.1.2. Connecting AC power AC24V AC24V 6.2. Connecting & Setting serial port 6.2.1. Connecting RS232 Within WebEye B101, there are four RS232 communication terminals; RX1, TX1, RX2, and TX2. When connecting RX1, and TX1, connect each pin to No. 1~3 hole. And when connecting, RX2, TX2, connect each pin to No.
If not, it may cause abnormal operation or damage on device. 6.3. Connecting & Setting sensor input 6.3.1. Specification In order to run sensor input of WebEye 2.0 B101 normally, the following conditions are required. Input Ch. 4Ch. Photo coupler differential inputs...
6.3.4. Setting sensor input Set a sensor type. (1) Run “WebEye 2 CofigStation Tool” (2) Log in the WebEye 2.0, and click “Event Source Input” menu. (3) Possible to set sensor by sensor. When setting as same value, use “Global” menu and click the “Apply”...
Hi-z, impedance will be set as no limit. 6.5. Video input / output Within WebEye 2.0 B101, there are video input and output terminal. To view image with CCTV monitor, input IMPEDANCE should be configured. Because Video input and output of WebEye 2.0 B101 is linked, any one between WebEye 2.0 B101 and CCTV monitor should be configured as...
Page 31
(4) Press the “Apply” button after setting. <Note> When connecting modem, set “Modem Initial Command”.
#1. Specification General 32bit RISC Embedded Processor Flash memory 16MB Main memory Embedded Linux Video channel NTSC or PAL video format are supported 1Ch. analog video inputs via BNC connector Image compression Algorithm Wavelet Resolution 720x486, 720x243, 360x243, 180x121, 90x60 (NTSC) 720x576, 720x288, 360x288, 180x144, 90x72 (PAL) Image compression rate 10:1 ~200:1...
Page 34
Environment Operation temperature -10C ~ +45C Storage temperature -25C ~ +70C Operation humidity 30% ~ 80% R.H (free of condensation) 93% R.H below (free of condensation) Storage humidity Additional function & Input/Output Additional function Image quality Control (10 Levels) Periodical sending the images through E-Mail, FTP 4.5 MB fresh memory for homepage customization Alarm Sending e-mail automatically...
S/N : Serial Number Management number for each Webgate product to combine twelve alphabet character and digit including model name, manufacturing year/month/week You can see serial number by looking at the bottom of product attached label and system info of Configuration Tool.
Page 36
WEBGATE Inc. 6F, Hanlim Venture Town Bldg., 689-6, Geumjeong-dong, Gunpo-si, Gyeonggi-do, Korea (435-862) Tel : (82-31) 428-9300 Fax : (82-31) 428-3955 Sales@webgateinc.com www.webgateinc.com...