Lubrication Oils; Oil Level Check; Check Engine Oil Level - Atlas Copco XAHS 37 DD Instruction Manual

Instruction Manual
4.3 L
UBRICATION OILS
High-quality, mineral, hydraulic or synthesized hydrocarbon oil with
rust and oxidation inhibitors and anti-foam and anti-wear properties
is recommended. The viscosity grade should correspond to the
ambient temperature and ISO 3448, as follows:
Type of lubricant
between 30°C and 40°C
between 30°C and -5°C
between -5°C and -20°C
PAROIL from Atlas Copco is the ONLY oil tested and approved for
use in all engines built into Atlas Copco compressors and generators.
Extensive laboratory and field endurance tests on Atlas Copco
equipment have proven PAROIL to match all lubrication demands in
varied conditions. It meets stringent quality control specifications to
ensure your equipment will run smoothly and reliably.
The quality lubricant additives in PAROIL allow for extended oil
change intervals without any loss in performance or longevity.
PAROIL provides wear protection under extreme conditions.
Powerful oxidation resistance, high chemical stability and rust-
inhibiting additives help reduce corrosion, even within engines left
idle for extended periods.
PAROIL contains high quality anti-oxidants to control deposits,
sludge and contaminants that tend to build up under very high
temperatures.
PAROIL's detergent additives keep sludge forming particles in a fine
suspension instead of allowing them to clog your filter and accumulate
in the valve/rocker cover area.
PAROIL releases excess heat efficiently, whilst maintaining excellent
bore-polish protection to limit oil consumption.
PAROIL has an excellent Total Base Number (TBN) retention and
more alkalinity to control acid formation.
PAROIL prevents Soot build-up
PAROIL is optimized for the latest low emission EURO -3 & -2, EPA
TIER II & III engines running on low sulphur diesel for lower oil and
fuel consumption.
PAROIL 5W40 is a Synthetic ultra high performance diesel engine oil
with a high viscosity-index. Atlas Copco PAROIL 5W40 is designed
to provide excellent lubrication from start-up in temperatures as low
as -20°C.
PAROIL 15W40 is a mineral based high performance diesel engine oil
with a high viscosity- index. Atlas Copco PAROIL 15W40 is designed
to provide a high level of performance and protection in 'standard'
ambient conditions as from -5°C.
*
If you want to use another brand of oil, consult the
engine instruction manual.
**
It is strongly recommended to use Atlas Copco branded
lubrication oils for the compressor. If you want to use
another brands of oil, consult Atlas Copco.
Compressor** Engine*
PAROIL S PAROIL 15W40
PAROIL M PAROIL 15W40
PAROIL S
PAROIL S PAROIL 5W40
Mineral compressor oil PAROIL M:
- 5 liter can: order number 1615 5947 00
- 20 liter can: order number 1615 5948 00
- 210 liter barrel: order number 1615 5949 00
Synthetic compressor oil PAROIL S:
- 5 liter can: order number 1615 5950 01
- 20 liter can: order number 1615 5951 01
- 210 liter barrel: order number 1615 5952 01
Mineral engine oil PAROIL 15W40:
- 5 liter can: order number 1615 5953 00
- 20 liter can: order number 1615 5954 00
- 210 liter barrel: order number 1615 5955 00
Synthetic engine oil PAROIL 5W40:
- 5 liter can: order number 1604 6060 01
- 20 liter can: order number 1604 6059 01
Never mix synthetic with mineral oil.
Remark:
When changing from mineral to synthetic oil (or the
other way around), you will need to do an extra rinse:
After doing the complete change procedure to synthetic
oil, run the unit for a few minutes to allow good and
complete circulation of the synthetic oil. Then drain the
synthetic oil again and fill again with new synthetic oil.
To set correct oil levels, proceed as in normal
instruction.
4.4 O
IL LEVEL CHECK
Never mix oils of different brands or types.
Use only non-toxic oils where there is a risk of inhaling
delivered air.
4.4.1 C
HECK ENGINE OIL LEVEL
Consult also the Engine Operation Manual for the oil specifications,
viscosity recommendations and oil change intervals.
See schedule 4.2.
Check engine oil level according to the instructions in the Engine
Operation Manual and top up with oil if necessary.
43