Radio And Tv Interference - Patton electronics 1193 User Manual

T T A A B B L L E E O O F F C C O O N N T T E E N N T T S S
Section
1.0 Warranty Information .............................................................2

1.1 Radio and TV Interference

Warning...........................................................................2
1.2 CE Notice........................................................................3
1.3 Service.............................................................................3
2.0 General Information...............................................................4
2.1 Features
2.2 Description
3.0 Configuration .........................................................................5
3.1 Configure the Hardware DIP Switches
3.1.1 Configure Model 1193
3.1.2 Select RJ-48C or BNC Connectors
4.0 Installation .............................................................................9
4.1 Connect the G.703/G.704 Network
4.1.1 Connect Twisted Pair to G.703/G.704 Network
4.1.2 Connect Coax Cable to the G.703/G.704 Network
4.2 Connect the Fiber Interface
4.3 Power Connection
4.3.1 Universal AC Power
4.3.2 DC Power
5.0 Operation .............................................................................12
5.1 Power-Up
5.2 LED Status Monitors
5.3 Test Modes
5.3.1 Local Loopback
5.3.2 Remote Digital Loopback (RDL)
5.3.3 The V.52 Test Pattern Generator
Appendix A - Specifications ........................................................17
Appendix B - Factory Replacement Parts and Accessories.......19
Page
1
1 1 . . 0 0 W W A A R R R R A A N N T T Y Y I I N N F F O O R R M M A A T T I I O O N N
Patton Electronics warrants all Model 1193 components to be
free from defects, and will—at our option—repair or replace the prod-
uct should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials,
and does not cover customer damage, abuse or unauthorized modifi-
cation. If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or consequen-
tial damages arising from the use of or inability to use this product.
Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall
be deemed an acceptance of these terms by the user.
1.1 RADIO AND TV INTERFERENCE
The Model 1193 generates and uses radio frequency energy, and
if not installed and used properly—that is, in strict accordance with the
manufacturer's instructions—may cause interference to radio and tele-
vision reception. The Model 1193 has been tested and found to com-
ply with the limits for a Class A computing device in accordance with
the specifications in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection from such interference in a
commercial installation. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If the Model 1193 does
cause interference to radio or television reception, which can be deter-
mined by disconnecting the unit, the user is encouraged to try to cor-
rect the interference by one or more of the following measures: mov-
ing the computing equipment away from the receiver, re-orienting the
receiving antenna and/or plugging the receiving equipment into a dif-
ferent AC outlet (such that the computing equipment and receiver are
on different branches).
WARNING: This device utilizes a class IIIB laser device which emits
invisible light. There is potential for eye damage if proper caution is not
taken. The laser port output is classified as class IIIA due to attenua-
tion in the fiber cable. Eye protection should be worn at all times when
the unit is operational and the laser port is not connected. The laser
assembly should not be modified in any way. The fiber cable should
never be disconnected from the laser device for any reason. The
laser's wavelength is specified in the range of 1280 nm to 1330 nm
with a maximum power output of 800 uw. Eye protection should be
specified to handle the stated wavelength. Never look directly into to
the laser port.
2