Patton electronics 1193 User Manual
  1. Manuals
  2. Brands
  3. Patton electronics Manuals
  4. Modem
  5. 1193
  6. User manual

Patton electronics 1193 User Manual

Single-mode fiber modem with fixed g.703/g.704 interface
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
USER
MANUAL
MODEL 1193
Single-Mode Fiber Modem
with Fixed G.703/G.704
Interface
Part# 07M1193-UM
SALES OFFICE
Doc# 01713U2-001,
(301)975-1000
Rev. C
TECHNICAL SUPPORT
Revised 10/25/06
(301)975-1007
An ISO-9001
http://www.patton.com
Certified
Company

Advertisement

Table of Contents
loading

Related Manuals for Patton electronics 1193

Summary of Contents for Patton electronics 1193

  • Page 1 USER MANUAL MODEL 1193 Single-Mode Fiber Modem with Fixed G.703/G.704 Interface Part# 07M1193-UM SALES OFFICE Doc# 01713U2-001, (301)975-1000 Rev. C TECHNICAL SUPPORT Revised 10/25/06 (301)975-1007 An ISO-9001 http://www.patton.com Certified Company...

  • Page 2: Radio And Tv Interference

    However, there is no guarantee that interfer- ence will not occur in a particular installation. If the Model 1193 does cause interference to radio or television reception, which can be deter-...
  • Page 3 Figure 1. Network extension between remote locations The Model 1193 is designed to transmit/receive G.703/G.704 data over one string of fiber. The Model 1193 allows transmission over Single-mode fiber with distances up to 50km (31 miles). The clocking options for the Model 1193 include Internal, Network (from G.703/G.704 Network), or Receive Recovered clock (from fiber line).

  • Page 4: Configuring The Hardware Dip Switches

    Note: The Model 1193 units are intended to work in pairs. Set the clock modes for the Model 1193 units with one end of the link set for receive recover and the other end set for either internal or network.
  • Page 5 Switches S5 through S8 are reserved for future applications and should be set to OFF. 3.1.2 Select RJ-48C or BNC Connectors The Model 1193 is shipped configured for use with a BNC connec- tion to the G.703/G.704 Network. If your Network connection is using BNC, skip this section.

  • Page 6: Connect The Fiber Interface

    From Network To Network WARNING: Model 1193 uses a Laser Diode to transmit invisible light into the fiber. Exposing eyes to this light can cause permanent damage. To prevent eye damage, DO NOT DIRECT DISCONNECTED FIBER OR FIBER CONNECTOR OF THE MODEM IN THE DIRECTION OF THE EYES.

  • Page 7: Power Connection

    (center pin is +5V). The universal input power supply has a male IEC-320 power entry connector. This power supply con- nects to the Model 1193 by means of a barrel jack on the rear panel. Many international power cords are available for the universal power supply (Refer to Appendix B for country-specific power cords).

  • Page 8: Test Modes

    Network and a local connection. Any data sent to the local Model 1193 in this test mode will be echoed (returned) back to the user (see Figure 11 below). If two Model...
  • Page 9 Loopbacks, follow these instructions: 1. Locate the "511/511E" toggle switch on the front panel of the Model 1193 and move it UP. This activates the V.52 BER test mode and transmits a "511" test pattern into the loop. If any errors are present, the local modem's red "ER"...

  • Page 10: Specifications

    A A P P P P E E N N D D I I X X A A PATTON ELECTRONICS G.703/G.704 SDSL MODEM SPECIFICATIONS Clocking Modes: Network (G.703/G.704), Internal, Receive Recover Line Rate: 2048 kbps Diagnostics: V.52 compliant (511/511E) pattern generator and detector with error injection mode.
  • Page 11 PATTON ELECTRONICS MODEL 1193 FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Electronics Model # Description 1193 ...Single-mode fiber optic modem 1193RC...Single-mode fiber rack card modem 48V-PSM ...DC Power Supply Module 08055DCUI ...100-240VAC (+5V ±5% reg. DC/2A) Universal Input Adapter 0805EUR ...European Power Cord CEE 7 (“A”) 0805UK ...United Kingdom Power Cord (“D”)

Table of Contents