Devices - Cisco UC320W Administration Manual

• Troubleshooting: Provides access to the support tools.

Devices

Use the Status > Devices page to view statistics for the Cisco UC320W, the SPA8800 IP telephony
gateways, and the IP phones.
Cisco UC320W Front Panel
Refer to the illustration for the current port states, corresponding to the lights on the front panel of the
hardware.
• POWER/SYS: Green - Normal operation. Slow flashing - Booting up. Fast flashing - Upgrading
firmware. Off - No power.
• LAN 1: LAN 1 port status: Green - Connected to a device on this port. Flashing - Sending or
receiving data. Off- Not connected.
• LAN 2: LAN 2 port status: Green - Connected to a device on this port. Flashing - Sending or
receiving data. Off- Not connected.
• LAN 3: LAN 3 port status: Green - Connected to a device on this port. Flashing - Sending or
receiving data. Off- Not connected.
• LAN 4: LAN 4 port status: Green - Connected to a device on this port. Flashing - Sending or
receiving data. Off- Not connected.
• WAN: WAN port status: Green - Connected to WAN. Flashing - Sending or receiving data. Off-
Not connected.
• PHONE (FXS): Phone (FXS) port status: Green - Service is available on the port, and the port is
not in use. Slow Flashing - Service is available and the attached phone is off hook (in use). Off -
The port is disabled.
• LINE (FXO) 1: Line (FXO) port 1 status: Green - PSTN line loop detected on this port. Slow
Flashing - FXO port is in use. Off - Not connected.
• LINE (FXO) 2: Line (FXO) port 2 status: Green - PSTN line loop detected on this port. Slow
Flashing - FXO port is in use. Off - Not connected.
• LINE (FXO) 3: Line (FXO) port 3 status: Green - PSTN line loop detected on this port. Slow
Flashing - FXO port is in use. Off - Not connected.
• LINE (FXO) 4: Line (FXO) port 4 status: Green - PSTN line loop detected on this port. Slow
Flashing - FXO port is in use. Off - Not connected.
• WLAN: Wireless network status: Green - Wireless radio is on. Flashing - Sending or receiving
data. Off - Disabled.
• VM: Voicemail system status: Green - Voicemail is enabled. Fast Flashing - System is full. Slow
flashing - Retrieving or recording voicemail. Off - Disabled.
• USB 1: USB port 1 status: Green - A USB key is installed. Off - Not connected. Flashing -
Connected but not yet available for access.
• USB 2: USB port 2 status: Green - A USB key is installed. Off - Not connected.
• WPS: Green - WiFi Protected Setup succeeded. Slow flashing - Setup is in progress. Fast
flashing - Setup error. Off - Not in use. To configure a WiFi connection by using WPS, make
sure the wireless device is located near the Cisco UC320W, and then press and hold this button
until the WPS light flashes.
Cisco UC320W Status Information
• Device WAN MAC: The MAC address of the WAN interface.
• Device LAN MAC: The MAC address of the LAN interface.
• System Time: The current date and time.
• Night Time Ring Mode: The active operational mode: Day Mode Active or Night Mode Active.
• PMF Files Active: The number of Platform Modification Files that are active on the Cisco
UC320W. These files may be provided to you by Cisco support personnel.
• Alter PMFs: Click this button to add or remove Platform Modification Files. For more information,
see the "Working with Platform Modification Files" section below.
• Current firmware version: The current firmware that is installed on the device.
50