Do you have a question about the dv-cp702 and is the answer not in the manual?
Questions and answers
John A.
February 4, 2025
My DV-CP702 plays and then jumps within the playing track -for an example, from 2 minutes ito 6minutes in the same playing track,
1 comments:
Mr. Anderson
May 14, 2025
The Onkyo DV-CP702 may jump within a playing track due to a dirty disc. You should remove the disc and clean it. If the issue persists, power supply voltage fluctuations or static electricity could be interfering with normal operation. In that case, turn off the DV-CP702, wait five seconds, then turn it back on. If that does not work, disconnect the power cord, wait five seconds, reconnect it, and try again.
Page 1
COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE...
DV-CP702 3 7 63 1515 0 SERVICE PROCEDURES-1 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs a laser. Therefore, be sure to follow carefully the instructions below when servicing. Laser Diode Properties WARNING!! Wavelength: 650/780nm (DVD/CD) SERVICE WARNING : DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY.
Page 4
DV-CP702 3 7 63 1515 0 SERVICE PROCEDURES-2 2. Safety-check out (Only U.S.A. model) After correcting the original service problem perform the following safety check before releasing the set to the customer Connect the insulating-resistance tester between the plug of power supply cord and terminal GND on the back panel.
This button is used to display information about the cur- STANDBY/ON button rent disc, title, chapter, or track, including the elapsed This button is used to set the DV-CP702 to On or time, remaining time, total time, and so on. Standby.
Page 6
Chain mode selected. When the disc tray is closed, all of the disc indicators appear until the DV-CP702 has checked each bay for the DISC indicator presence of a disc. If a bay is found to have no disc, the The number of the currently selected disc appears here.
Page 7
AV receiver, or surround sound decoder (Dolby Pro Logic). REMOTE CONTROL These (Remote Interactive) connectors can be con- nected to the connectors on your other Onkyo AV components for interactive control. u163 http://www.xiaoyu163.com...
3 7 63 1515 0 PANEL VIEW-4 STANDBY button REMOTE CONTROLLER-1 This button is used to set the DV-CP702 to Standby. ON button This button is used to turn on the DV-CP702. Don't turn on the DV-CP702 until you've completed, and double checked all connections.
Page 9
DV-CP702 3 7 63 1515 0 PANEL VIEW-5 REMOTE CONTROLLER-2 REPEAT button This button is used to set the Repeat Playback functions. A-B button This button is used to set the A-B Repeat Playback function. RANDOM button This button is used with the Random Playback function.
http://www.xiaoyu163.com 3 7 63 1515 0 BLOCK DIAGRAM P1001 LASER etc DVD MECHA P1101 SPD+,SPD-,SLD+,SLD,LMT-SW U1 : NADG-7807 DVD Main circuit PC board P2901 P2501 U30 : POWER SUPPLY UNIT EV5V L 13942296513 SW5V P 9 0 1 NGPS-0036 (US) SW3.3V P 7 1 0 A SW8V...
Page 21
DV-CP702 3 7 63 1515 0 NOTE THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY. REPLACE ONLY WITH PART NUMBER SPECIFIED. VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE. (NO INPUT SIGNAL) ELECTROLYTIC CAPACITORS ARE IN uF/WV. ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
Page 28
DV-CP702 3 7 6 3 1 5 1 5 0 To Audio out PC board (U6) A G N D SCHEMATIC DIAGRAM-2 A 3 . 3 V P2002B P2001B D G N D D 3 . 3 V A G N D A 1 .
Page 29
DV-CP702 3 7 6 3 1 5 1 5 0 SCHEMATIC DIAGRAM-3 : FRONT DISPLAY PC BOARD NADIS-7808 Q802 HNV-12SM34 NOTE THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY. REPLACE ONLY WITH PART NUMBER SPECIFIED. VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 PC BOARD CONNECTION DIAGRAM AC IN U30 : Power supply unit NGPS-0036-100-120V <CDD1N> NGPS-0037-100-240V <CPA4P> L 13942296513 U11: Roulette motor U13: Disc sensor PC board PC board ETC7816 NAETC-7818 P707B P709A U12: Loading motor PC board ETC-7817 Z702 U9: Standby switch PC board...
Page 34
DV-CP702 3 7 6 3 1 5 1 5 0 PC BOARD CONNECTION DIAGRAM AC IN P1292 P1291 P202B Q412 P301 P202A SPD+ SPD- P201 P402 SLD+ SLD- LMT-SW DACRST DGND AMUTE CSDMIX U5: Video output terminal PC board...
Page 35
DV-CP702 3 7 63 1515 0 PRINTED CIRCUIT BOARD VIEW-1 : DVD MAIN CIRCUIT PC BOARD (NADG-7807) L 13942296513 u163 : Side A pattern : Sise B pattern http://www.xiaoyu163.com...
DV-CP702 3 7 63 1515 0 PRINTED CIRCUIT BOARD VIEW-2 : DVD MAIN CIRCUIT PC BOARD (NADVG-7807) L 13942296513 u163 : Side B pattern : Side A pattern http://www.xiaoyu163.com...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q1001 : CXD1881BR DVD ANALOG FRONTEND-3 TERMINAL DESCRIPTION Power supply Pin Name Description Power supply for RF section and serial port. Power supply for servo section. Ground pin for RF section and serial port section.
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q1001 : CXD1881BR DVD ANALOG FRONTEND-4 TERMINAL DESCRIPTION Analog pins Pin Name Description The RF AGC integration capacitor CBYP is connected between BYP and VPA. Deferential phase tracking LPF pin.
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q1201: CXD1885Q (DVD DSP)-2 16/4M DRAM ECC Core Data Memory Demodulator Sicer mamager MPEG I/F Video Data-PLL CD-DSP (DDCD) VSTEM Serial VSTEM Command Serial I/F ASP Serial I/F...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q1201: CXD1885Q (DVD DSP)-5 Sign Classification Description ASP I/F FRO signal processing port. Serial data input control ASP I/F FRO signal processing port. Serial data output control SCLKH ASP I/F FRO signal processing port.
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q1201: CXD1885Q (DVD DSP)-6 Sign Classification Description DRAM I/F Address output port-8 of DRAM DRAM I/F Address output port-7 of DRAM DRAM I/F Address output port-6 of DRAM...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q1201: CXD1885Q (DVD DSP)-7 Sign Classification Description GIO12 General Port General port-12 DVSS VDD & GND Digital GND GIO13 General Port General port-13 GIO14 General Port General port-14...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q2303 : IC42S16400-7T SYNCHRONOUS DYNAMIC RAM The IC42S16400 are high-speed 67, 108, 864-bit synchronous dynamic ramdam-access memories, organized as 2,097, 152 x 8 x 4 and 1,48, 576 x 16 x 4 (word x bit x bank), respectively.
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q2003 : IS24C08-3Z EEPROM (8K-Bit 2-Wire Serial CMOS EEPROM) PIN CONFIGURATION PIN DESCRIPTIONS A0-A2 Address Inputs Serial Address/Data I/O Serial Clock Input Write Protect Input Power Supply Ground This input clock pin is used to synchronize the data transfer to and from the device.
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION PORT ASSIGMENT-1 Class Port name Function 1 Function 2 Function 3 I/O Description I/O Descrition I/O Descrition HA[11] O CPU Address HA[12] O CPU Address HA[13] O CPU Address...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION PORT ASSIGMENT-2 Class Port name Function 1 Function 2 Function 3 I/O Description I/O Descrition I/O Descrition PI02[5] I/O Port 25 O BSEL2 PI02[6] I/O Port 26 O BSEL1...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION PORT ASSIGMENT-3 Class Port name Function 1 Function 2 Function 3 I/O Description I/O Descrition I/O Descrition O SDRAM Chip select output pin DCS2 O SDRAM Chip select output pin...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION PORT ASSIGMENT-4 Class Port name Function 1 Function 2 Function 3 I/O Description I/O Descrition I/O Descrition ACLKI Audio clock input pin CLKIN System clock input pin CLK0...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q2502: TC7SZ125FU (BUS BUFFER 3-STAGE OUTPUT) PIN ASSIGNMENT IN A Truth table INPUT OUTPUT OUT Y (Top view) X: Don't care Z: High impedance L 13942296513 u163 http://www.xiaoyu163.com...
DV-CP702 3 7 63 1515 0 IC BLOCK DIAGRAM/ TERMINAL DESCRIPTION Q2301: TC74VCX162373FT 16-BIT D-TYPE LATCH PIN ASSIGNMENT Truth Table Inputs Outputs 1D1-1D8 1Q1-1Q8 SYSTEM DIAGRAM Inputs Outputs 2D1-2D8 2Q1-2Q8 LE Q LE Q LE Q LE Q LE Q...
DV-CP702 3 7 63 1515 0 MICROPROCESSOR TERMINAL DESCRIPTION-2 Sign Functional name I/O Description P15/ANI5 P16/ANI6 P17/ANI7 MCRST O Reset output pin for sub microprocessor. Avss AVSS I To connect VSS. P130/ANO0 P131/ANO1 FL ON/OFF O Power ON/ OFF pin of FL tube.
DV-CP702 3 7 63 1515 0 MICROPROCESSOR TERMINAL DESCRIPTION-3 Sign Functional name Description P64/RD Not used. To connect to GND P65/WR Not used. To connect to GND P66/WAIT Not used. To connect to GND P67/ASTB Not used. To connect to GND...
DV-CP702 3 7 63 1515 0 PART REPLACEMENT-1 1. CABINET REPLACEMENT 1-3. Tray panel and Mechanism assy <Mechanism assy> 1-1. Top cover and front panel 1-3-1. Remove four screws. (1) 1-1-1. Remove the top cover. (six screws) 1-3-2. Remove the mechanism assy.
DV-CP702 3 7 63 1515 0 PART REPLACEMENT-2 Tray panel <Mounting> 1-4-4. Insert the tray panel. 1-4-5. Set the FFC (P707) to mechanism control PC board assy. 1-4-6. The pin of main gear and fiting the position of the slot on the tray.
DV-CP702 3 7 63 1515 0 UPDATE FIRMWARE-1 TV monitor 1 Check the version of firmware Region Code: Software Version: 1.10.A 1. Press the "STOP" key, while the set press Loader: 01.31 6 the "DISPLAY" key in state of No DISC condition.
DV-CP702 3 7 63 1515 0 UPDATE FIRMWARE-2 Exchange of DVD main board (NADG-7807) 1 Update firmware Check the version of present firmware. DVD main board is not necessarily in the newest version. 2 Setting the region code RC-484M [Preparation] Remote controller: RC-484M Part No.
PRINTED CIRCUIT BOARD PARTS LIST-1 DV-CP702 U1 : DVD MAIN CIRCUIT PC BOARD 3 7 63 1515 0 CIRCUIT NO. PART NAME PART NO. DESCRIPTION REMARK C1001 C-CERA C 150D-104K-P-AC CK725B1C-104K1 C1002 C-CERA C 150D-104K-P-AC CK725B1C-104K1 C1003 C-CERA C...
DVD MECHANISM SECTION PARTS LIST DV-CP702 3 7 63 1515 0 PART NAME PART NO. DESCRIPTION REMARK N Q'TY RAIL 4154-6031-2 Loading motor assy Q0090C-MOTCC (M2)+(M3) (M2) MOTOR 8913-6002-1 CCM07B-045R1-1A (M3) PULLEY 4154-6001-0 M2*1 NSP SCREW 2900-2604-0000 2.6TTP+4S M1*2...
http://www.xiaoyu163.com DVD Main circuit PC board assy PCB-Q0090C-MPEGA NADG-7807-1A <CDD1N> 3 7 63 1515 0 DVD Main circuit PC board assy PCB-Q0090C-MPEGB NADG-7807-1A <CPA4P> Display circuit PC board assy PCB-Q0150C-MAINA NADIS-7808-1A <CDD1N> Display circuit PC board assy PCB-Q0150C-MAINB NADIS-7808-1B <CPA4P> (U3) Front disp.
Need help?
Do you have a question about the dv-cp702 and is the answer not in the manual?
Questions and answers
My DV-CP702 plays and then jumps within the playing track -for an example, from 2 minutes ito 6minutes in the same playing track,
The Onkyo DV-CP702 may jump within a playing track due to a dirty disc. You should remove the disc and clean it. If the issue persists, power supply voltage fluctuations or static electricity could be interfering with normal operation. In that case, turn off the DV-CP702, wait five seconds, then turn it back on. If that does not work, disconnect the power cord, wait five seconds, reconnect it, and try again.
This answer is automatically generated