Advertisement
Test run
6WHS 3HUIRUP WKH WHVW UXQ DQG FKHFN WKH DLUÀRZ WHPSHUDWXUH DQG DXWR YDQH
1 Press the
F1
button to go through the operation modes in the order of "Cool"
and "Heat". (Fig. 6-5)
Cool mode: Check the cold air blow off.
Heat mode: Check the heat blow off.
* Check the operation of the outdoor unit's fan.
2 Press the
button and open the Vane setting screen.
$872 YDQH FKHFN
1 Check the auto vane with the
F1
2 Press the
button to return to "Test run operation".
3 Press the
button.
)LJ
)LJ
buttons. (Fig. 6-6)
F2
A
Insert the pump end 3 to 5 cm
B
Cover of water supply inlet
C
$ERXW FF
D
Water
E
Drain plug
Test run
Remain
Pipe
Cool
Auto
Switch disp.
Mode
Fan
F1
F2
F3
F4
)LJ
8VLQJ ZLUHOHVV UHPRWH FRQWUROOHU )LJ
1
Turn on the power to the unit at least 12 hours before the test run.
2
Press the
button twice continuously.
(Start this operation from the status of remote controller display turned off.)
A
and current operation mode are displayed.
3
Press the
button to activate
cool air is blown out from the unit.
4
Press the
button to activate
warm air is blown out from the unit.
5
Press the
button and check whether fan speed changes.
6
Press the
button and check whether the auto vane operates properly.
7
3UHVV WKH 212)) EXWWRQ WR VWRS WKH WHVW UXQ
Note:
‡ 3RLQW WKH UHPRWH FRQWUROOHU WRZDUGV WKH LQGRRU XQLW UHFHLYHU ZKLOH IROORZLQJ
2
7
steps
to
.
‡ ,W LV QRW SRVVLEOH WR UXQ WKH LQ )$1 '5< RU $872 PRGH
&KHFN RI GUDLQDJH )LJ
‡ 'XULQJ WKH WULDO UXQ HQVXUH WKH ZDWHU LV EHLQJ SURSHUO\ GUDLQHG RXW DQG WKDW QR ZDWHU
is leaking from joints.
‡ $OZD\V FKHFN WKLV GXULQJ LQVWDOODWLRQ HYHQ LI WKH XQLW LV QRW UHTXLUHG WR SURYLGH FRRO-
LQJGU\LQJ DW WKDW WLPH
‡ 6LPLODUO\ FKHFN WKH GUDLQDJH EHIRUH ILQLVKLQJ FHLOLQJ LQVWDOODWLRQ LQ D QHZ SUHPLVHV
5HPRYH WKH FRYHU RI WKH ZDWHU VXSSO\ LQOHW DQG DGG DERXW FF RI ZDWHU XVLQJ
a water supply pump etc. During this process, be careful not to spray water into
the drain pump mechanism.
(2) Confirm that water is being drained out through the drainage outlet, after switching
over from remote control mode to trial run mode.
(3) After checking the drainage, ensure that the cover is replaced and the power
supply is isolated.
(4) After confirming the drainage system is functioning, replace the drain plug.
Remain
Vane
F1
F2
F3
F4
)LJ
mode, then check whether
mode, then check whether
Advertisement
