Shark DE-2010 Operating Instructions Manual
Hide thumbs
Also See for DE-2010:
- Operating instructions manual (20 pages) ,
- Operating instructions manual (16 pages)
Related Manuals for Shark DE-2010
Summary of Contents for Shark DE-2010
- Page 1 MODEL: DE OPERATING INSTRUCTION AND PARTS MANUAL DE-2010 DE-2015 DE-3010 DE-3520 For technical assistance or the SHARK dealer nearest you, call 1-800-771-1881 or visit our website at www.shark-pw.com 97-710...
-
Page 2: Table Of Contents
CONTENTS Important Safety Information ..............3-4 Component Identification ................ 5 Assembly Instructions ................6 Operating Instructions ................7 Applying Detergent and General Operating Techniques ......8 Shut Down and Clean-Up ............... 9 Storage ....................9 Troubleshooting ..................10 Preventative Maintenance ..............11 Oil Change Record ................ -
Page 3: Important Safety Information
WARNING: Flammable liquids INTRODUCTION WARNING can create fumes which can ig- nite causing property damage or Thank you for purchasing this Pressure Washer. severe injury. All information in this manual is based on the latest prod- WARNING: Risk of explosion — uct information available at the time of printing. - Page 4 11. Manufacturer will not be liable for any changes made to our standard machines, or any components not purchased from us. 12. Be certain all quick coupler fittings are secured be- fore using pressure washer. 13. Never run pump dry or leave spray gun closed longer than 5 minutes.
-
Page 5: Component Identification
COMPONENT IDENTIFICATION Water Supply (not included) Pressure Unloader Nozzle Quick On/Off Coupler Switch Pump Wand Hanger Detergent Bucket (not included) Garden Hose (not included) High Pressure Spray Gun GFCI Hose and Wand Pump — Develops high pressure. High Pressure Hose — Connect one end to water pump discharge nipple and the other end to spray gun. -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTIONS Bolts Carriage Hose/Gun Handle Bolt Storage Bracket Alignment Holes Frame Assy. Studs STEP 1: Attach the handle to the STEP 2: Insert the carriage bolt through STEP 3: Attach the spray gun/ frame of the pressure washer. the holes from the outside of the unit hose storage handle, and Note: It may be necessary to move and attach a nut from the inside of the... -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Cold Water Source Garden Hose STEP 1: Connect garden hose to the STEP 2: Trigger the spray gun to STEP 4: Connect to ap- cold water source and turn water on eliminate trapped air then wait for propriate power supply. completely. -
Page 8: Applying Detergent And General Operating Techniques
DETERGENTS AND GENERAL OPERATING TECHNIQUES WARNING: Some detergents pump protector engages and cools the pump by dis- WARNING charging the warm water onto the ground. This thermal may be harmful if inhaled or in- device prevents internal damage to the pump. gested, causing severe nausea, fainting or poisoning. -
Page 9: Shut Down And Clean-Up
SHUTTING DOWN AND CLEAN-UP On/Off Switch STEP 3: Turn off water supply. STEP 1: Remove de- STEP 2: Turn off machine by STEP 4: Press trigger flipping switch on rear of mo- tergent suction tube to release water pres- from container and in- tor. -
Page 10: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Pump sucking air Check water supply and possibility of air seepage. PUMP RUNNING NORMALLY BUT Check valves sticking Check and clean or replace if necessary. PRESSURE LOW ON Unloader valve seat faulty Check and replace if necessary. INSTALLATION Nozzle incorrectly sized Check and replace if necessary. -
Page 11: Preventative Maintenance
PREVENTATIVE MAINTENANCE PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. -
Page 12: Exploded View
EXPLODED VIEW (Models 352007A, 352009A) (Model 4-20021A) 1-1/2HP 96-720, 97-708, 97-709, 97-710 • REV. 2/04... -
Page 13: Exploded View Parts List
EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION See Specifications Page 18, For Proper Size 6-020204 Switch, 2 Pos. 120V-600V, 4-12803015 Nozzle, 1503, Yellow 1-3Ph Bremas 4-12803025 Nozzle, 2503, Green 6-03911 Lid, Plastic, Carlon E9801 4-12803040 Nozzle, 4003, White 4-12803000 Nozzle, 0003, Red... - Page 14 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 95-07102382 Hanger, Hose/Wand, CG/ 95-07104922 Handle, Bumper, Red (EP, DL DE Models) 95-07104962 Handle, Bumper, Chrome (PDE 90-100471 Bolt, Carriage, 1/4”-20 x Models) 1-1/2” 95-07104927 Base, CW Direct, Red (EP, DL 90-10072 Bolt, Carriage, 5/16”...
-
Page 15: Hose And Spray Gun Assembly
HOSE AND SPRAY GUN ASSEMBLY HOSE AND SPRAY GUN ASSEMBLY PARTS LIST ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 2-2002 Coupler, 3/8" Female 2-2000 Coupler, 1/4” Female 2-0121 Quick Coupler O-Ring 1 2-0119 Quick Coupler O-Ring 4-0203050C Hose, 50' x 3/8" w/Coupler( EP, Nozzle, See Page 18 For Size PDE, DL Models) 4-16540... -
Page 16: Pde4-30025A, B, C Exploded View
PDE4-30025A, B, C EXPLODED VIEW 96-720, 97-708, 97-709, 97-710 • REV. 2/04... -
Page 17: Pde4-30025A, B, C Parts List
ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 10-020PDE Label, PDE, Lexan 6-03904 Enclosure, Fiberglass, NEMA4X 2-1902 Strainer, Inlet Garden Hose 1 11-1042 Label, Ground 6-010690 Cord w/GFCI, 240V, 30 Amp 10-08015A Label, PE Off/On, For Push TRC (4-3000A) Buttons 6-0109 Cord, Service, SEO 10/4 (4-3000B) -
Page 18: Specifications
SPECIFICATIONS Machine Pessure Nozzle Pump Pump Unloader Motor Motor Model (PSI) Size Hose p/n Part # Model Part # Par t # EP-201009D 1000 4-0203050C 5-1802 HC205AL 5-3303 1-1/2 5-1004M EP-301009D 1000 4-0203050C 5-1806 HC235 5-3303 5-1073 EP-301509A 1500 4-0203050C 5-1806 HC235 5-3303... -
Page 19: Warranty
TICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of SHARK products conforms to local codes. - Page 20 Form #97-710 • Revised 2/04 • Printed in U.S.A.
Need help?
Do you have a question about the DE-2010 and is the answer not in the manual?
Questions and answers