Integra DTR-40.7 Basic Manual page 71

Level Calibration
Adjust the level of each speaker with the built-in test tone� Settings are automatically
configured if you use the Automatic Speaker Setup�
Setting Item Default Value
Front Left 0 dB
Center 0 dB
Front Right 0 dB
Height Left 0 dB
Height Right 0 dB
Surround Right 0 dB
Back Right 0 dB
Back Left 0 dB
Setting Details
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Setting Item Default Value
Surround Left 0 dB
Subwoofer 0 dB
● The speaker "Level Calibration" may be unable to be changed depending on the settings in
"Configuration" - "Speaker Channels" / "Subwoofer"�
● "Level Calibration" cannot be changed while muting is on�
Equalizer Settings
Adjust the output volume of each range of each connected speaker� You can adjust the
volume of each range of each speaker� You can set three types of equalizer settings in the
Presets 1, 2, and 3�
● You can adjust the bass in the low range frequencies (63 Hz, etc�), and the treble in the high range
frequencies (16 kHz, etc�)�
● You can select up to seven frequency bands for each speaker�
Setting Item Default Value
Front 0 dB
Center 0 dB
Height 0 dB
Surround 0 dB
Advanced Settings (Setup Menu)
Setting Details
Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Select a value between "-15 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Setting Details
First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the / cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the / cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the / cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
● This cannot be selected if "Configuration" -
"Powered Zone 2" is set to "Yes" and Zone2
is set to on�
First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the / cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
En-39