Integra DTR-40.7 Basic Manual page 103

Multi-zone Function
 There is no zone output from the connected player
¼
● With multi-zone function, sound is output only when the
signal input source is an external component connected
to the digital audio input jacks or analog audio input
jacks, "NET", "AM" or "FM"� Multi-zone output is not
possible if the player and the unit are connected via
HDMI cable�
Connect the player using a digital optical cable
(OPTICAL), digital coaxial cable (COAXIAL), or RCA
cable� Also, some players require audio output setting�
● Only analog and 2ch PCM audio signals can be output
from an external component to Zone 2�
● When the "NET" input source is selected, DSD and
Dolby TrueHD audio signals cannot be output to Zone 2�
Remote Controller
● Make sure that the batteries are installed with the
correct polarity�
● Install new batteries� Do not mix different types of
batteries, or old and new batteries�
● Make sure that the remote controller is not too far away
from the unit, and that there is no obstruction between
the remote controller and the remote control sensor of
the unit�
● Make sure that the unit is not subjected to direct
sunshine or inverter-type fluorescent lights� Relocate if
necessary�
● If the unit is installed in a rack or cabinet with colored-
glass doors or if the doors are closed, the remote
controller may not work reliably�
If the above does not solve the problem, check the
following�
 The remote controller does not work
¼
● Before operating this unit with the remote controller, be
sure to press RCV�
 Operating other Onkyo component by using a RI
¼
remote control code is not available
● Make sure that the Onkyo component is properly
connected with RI cable� When RI cable is used for
connection, make sure to connect analog audio cable as
well� (Connecting only an RI cable will not be enough�)
● Make sure you have selected the correct remote
controller mode�
● When the RI remote control code is input, point the
remote controller at remote control sensor of the unit�
● Make sure that the input display is correctly set�
● Input the RI remote control code again�
 Cannot operate Onkyo components (ones without RI
¼
connection) and components of other makers
● Operate the remote controller by setting toward the light
receiving section of each component�
● When using the remote controller to control other
manufacturers' AV components, some buttons may not
work as expected� Also, some components may not
operate at all�
● Make sure you have selected the correct remote
controller mode�
● Make sure you have entered the correct remote control
code�
● Make sure to set the same ID on both the unit and
remote controller�
● Input a correct remote control code again� If there are
several codes, try each code�
Display and OSD
 The display does not light
¼
● Make sure that Dimmer function is not working� Press
Dimmer button and change the brightness level of the
display�
 The on-screen menus do not appear
¼
● On your TV, make sure that the video input to which this
unit is connected is selected�
● Set "TV Out" - "Impose OSD" to "On"�
● The guidance displayed on the TV screen (OSD) are
not displayed when the OSD language is set to Chinese
if the input selector is "NET"� Operate by confirming
the display on the main unit� Note that the display on
the main unit does not support the display of Chinese
characters� Characters that cannot be displayed are
replaced with asterisks ( )�
RI Dock
● Make sure the unit is turned on, the correct input source
is selected, and the volume is turned up�
● Make sure cord and cable plugs are properly plugged in�
● Make sure your iPod/iPhone is properly inserted in
the Dock� If your iPod/iPhone is in a case, it may not
connect properly to the Dock� Always remove your iPod/
iPhone from the case before inserting it into the Dock�
Try reconnecting your iPod/iPhone�
● Make sure your iPod/iPhone is actually playing�
If the above does not solve the problem, check the
following�
 There is no sound
¼
● Try resetting your iPod/iPhone�
 There is no video
¼
● Make sure the correct input is selected on your TV or
the unit�
● Make sure that your iPod/iPhone model's TV OUT
setting is set to On�
● Some versions of the iPod/iPhone do not output video�
 The AV receiver's remote controller does not control
¼
your iPod/iPhone
● The iPod/iPhone cannot be operated while it is
displaying the Apple logo�
● Make sure you have selected the correct remote
controller mode�
● When you use the AV receiver's remote controller, point
it toward this unit�
● Before operating with the remote controller, you may
need to play on your iPod/iPhone to make the input
selector be recognized�
● Depending on your iPod/iPhone model and generation,
some buttons may not work as expected�
● Try resetting your iPod/iPhone�
 The unit unexpectedly selects your iPod/iPhone as
¼
the input source
● Always pause iPod/iPhone playback before selecting
a different input source� If playback is not paused, the
Direct Change function may select your iPod/iPhone
as the input source by mistake during the transition
between tracks�
Others
 Strange noises can be heard from the unit
¼
● If you have connected another unit to the same wall
outlet as this unit, this noise may be an effect from the
other unit� If the symptoms improve by unplugging the
power cord of the other unit, use different wall outlets for
this unit and the other unit�
 When performing Automatic Speaker Setup, the
¼
Troubleshooting
En-71