D9412Gv4/D7412Gv4 V2.00 (And Higher) Input Points And Peripheral Devices - Bosch D9412GV4 Installation Manual

14 en | Diagrams
3.3 D9412GV4/D7412GV4 v2.00 (and higher) Input Points and
Peripheral Devices (D125B, D129, D130) System Wiring
Diagram
Sw. Aux Pwr
Pnl Common
Pnl Common
Earth Ground
Figure 3.7: Input Points and Peripheral Devices System Wiring Diagram
Callout - Description
1 - (Optional): For 24 V applications use a UL 1481 Listed regulated, power-limited 24 VDC power supply with a
D130 Relay Module. Refer to the D130 Installation Instructions (P/N: F01U072455) for correct wiring
requirements.
2 - D130 Relay Module
3 - D125B Powered Loop Interface Module
4 - To UL Listed two-wire smoke detectors with a fire rated EOL resistor. Refer to Two-Wire Smoke Detectors
section in the Approved Applications chapter in the D9412GV4/D7412GV4 v2.03 Installation and System Reference
Guide (P/N: F01U265457) for a listing of compatible two-wire smoke detectors.
5 - 1 kΩ EOL resistor (P/N: F01U033966): For typical alarm applications.
6 - D129 Dual Class A Initiation Circuit Module: Provides optional Waterflow Alarm Retard feature. Not suitable
for two-wire smoke detectors.
Notice!
For D129, use zero retard except for waterflow devices.
All external connections except Terminal 5 (battery positive) are power limited.
2016.07 | 04 | F.01U.291.483
+ -
1
Zone B 2
Zone A
3
4
5
Loop B- 6
Loop A-
7
Loop B+ 8
Loop A+ 9
10
Commercial Protected-Premises Control Panel
10.2 VDC - Battery Load Shed
Refer to the D9412GV4/D7412GV4 Approved Applications Compliance Guide
(P/N: F01U201525) for System Wiring Diagram, Issue A and for
YELLOW - Charging Status
compatible smoke detectors. 2-wire Compatible Identifier "A".
Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2007:
RED - Low Battery - 12.1 VDC
UL Listed and Classified control unit Model D9412GV4, D7412GV4, or D7212GV4;
UL Listed and Classified keypad Model D1256, D1257, D1260, D1255, D1255R, or D1255RB;
UL Listed Local Bell
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
POWER SUPPLY REQUIREMENTS
CLASS 2 TRANSFORMER
Model D1640
1 The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
16.5 VAC 40 VA 60 Hz
Internally Fused - Do not short
Accessory Devices. For System Loading, refer to the D9412GV4/D7412GV4 Operation
Model D1640
Requires Unswitched Outlet
and Installation Guide (P/N: F01U201527).
Internally Fused - Do not short
Do not share with other equipment
Requires Unswitched Outlet
2 All external connections except Terminal 5 (battery positive) are inherently power
Do not share with other equipment .
limited. Requirements for battery standby time might reduce allowable output.
+ AUX POWER
CAUTION:
Refer to the D9412GV4/D7412GV4 Operation and Installation Guide
3
+ AUX POWER
(P/N: F01U201527) for Power Requirements relating to Terminals 6 and 7 .
BATTERY NEGATIVE ONLY
CAUTION: Avoid damage to Panel.
BATTERY NEGATIVE ONLY WARNING!
Do not connect 24 V to terminals.
4
CAUTION: Avoid damage to Panel. Multi-Battery installation requires
Maximum charging current 1.4 A
Do not connect 24 V to terminals.
Model D122 or D122L Dual Battery
BATTERY POSITIVE ONLY
Maximum charging current 1.4 A
Harness. Improper installation can
5
BATTERY POSITIVE ONLY.
be a fire hazard.
RELAY A PROGRAMMABLE
This equipment should be installed in accordance with the NFPA 70 (National Electrical Code) and
PROGRAMMABLE ALARM OUTPUTS
6 RELAY A
NFPA 72 (National Fire Alarm Code).
ALARM OUTPUTS Terminals
Terminals Not suitable for remote station protected premises services where separate transmission circuits
RELAY B 6
and 7
are required for fire, supervisory (when applicable) and trouble signals when using D185.
7 6 7
RELAY B and
SWITCHED AUX
The D9412GV4 Control Panel is UL Listed For Central Station, Remote Station, Local, Auxiliary,
SWITCHED AUX
RELAY C Terminal 8 Proprietary, and Household Fire Alarm, and Central Station, Local, Proprietary,
8 Police Station Connect, Household Burglar Alarm and Encrypted Line Security when
8 RELAY C Terminal
communicating via a network.
COMMON System is intended to be checked by a Qualified Technician at least every 3 years.
9 COMMON The types of initiating circuits the control panel has been approved for are A, M, W, SS.
The types of signaling the control panel has been approved for are DAC, OT, NC, RevPol.
EARTH GROUND
10 EARTH
Open
Normal
S4 GROUND FAULT DETECT
Point 1 Point 2 Point 3 Point 4
Point 1 Point 2 Point 3 Point 4
S4 GROUND FAULT DETECT Enabled
Disabled
Enabled
Disabled
PHONE LINE SEIZED LED
PHONE LINE SEIZED LED
ON when communicating
ON when communicating
OFF when idle
OFF when idle
TIP RING 11 12 13 14 15
TIP RING 11 12 13 14 15 16
RED
TELCO CORD MODEL D161
RED
TELCO CORD MODEL D161
COMMON
PHONE LINE
SEIZED
TIP RING
TELCO
UL Installation Guide
RED POWER +
YELLOW DATA BUS A
DATA BUS B
GREEN
RED POWER +
BLACK COMMON
DATA BUS A
YELLOW
GREEN SDI2 Connector DATA BUS B
SDI Connector
BLACK COMMON
Battery: Replace every 3 to
5 years with one or two Model
RED POWER +
D126 or D1218 12 V Lead Acid
N.F.P.A.
ZONEX OUT 1
Style 4.0
Batteries.
Signaling
27
31
YELLOW DATA BUS A Line
ZONEX IN 1
Circuits
DATA BUS B 30
GREEN
ZONEX OUT 2
29
BLACK COMMON 25
ZONEX IN 2
NFPA 28
ZONEX OUT 1
Style 4.0
ZONEX POWER +
Signaling
Line
VOLTAGE RANGES 27
ZONEX IN 1
Circuits
Open VOLTAGE RANGES 3.7 - 5.0 VDC ZONEX COMMON
Normal 2.0 - 3.0 VDC
3.7 - 5.0 VDC Short 0.0 - 1.3 VDC
Short 0.0 - 1.3 VDC
2.0 - 3.0 VDC 26
NOT USED
Point 5 Point 6 Point 7 Point 8
Point 8, S3 Option D5200/D5360
Point 5 Point 6 Point 7 Point 8
PROG CONN
Closed = 1 kΩ EOL
Operation
Normal Operation
Monitor 25
NOT USED
LED
Open =AB-12 UL
Pulses when Bell Box 220 kΩ
Normal
24
Operation Monitor LED
ZONEX POWER +
Flickers when
Pulses when Normal
Ringing
Flickers when Ringing
16 17 18 19 20 21 22
17 18 19 21 22
20
GREEN
23
ZONEX COMMON
GREEN
Bosch Security Systens, Inc.
1 Loop B+
2
Loop B-
Loop B-
3
4 Loop B+
5 Zone B
6 Aux Power
7 Earth Ground
8 Common
9
Zone A
10
Loop A+
11 Loop A-
12 Loop A-
13 Loop A+