Introduction; Safety & Warnings - Projectiondesign F22 User Manual

B

INTRODUCTION

This digital projector is designed with the latest state-of-the-art
technologies in illumination, imaging, optics, electronics, thermal and
industrial design in order to serve traditional as well as novel imaging
applications across a variety of markets, offering features such as:
- PROFESSIONAL GRADE POWERED PROJECTION LENSES with
bayonet mounts
- DUAL LAMP SYSTEM with separate lamps for improved life,
redundancy and 24/7 operation
- DUAL OPTOMECHANICAL IRIS for variable contrast and
brightness
- MECHANICAL SHUTTER for total black
- SXGA+ 1400x1050 pixel DLP™ technology
- SINGLE CHIP DMD™ with DarkChip3™ technology by Texas
Instruments ®
- HIGH CONTRAST for vibrant colors and deep blacks
- HIGH RESOLUTION for unprecedented detail
- HIGH BRIGHTNESS for larger screens
- DEEP BLACKS for maximum dynamics
- REDUCED IMAGE NOISE through high end signal processing
- FAROUDJA DCDi™ Video processing and de-interlacing
- ECO MODE for reduced power consumption and lower audible
noise
- VARIABLE LAMP POWER for alignment of multi-screen
configurations
- LONG LIFE LAMP (up to 4000 hours) in low power ECO mode
- STYLISH AND COMPACT DESIGN to fit most applications,
installed or movable
- MULTIPLE LENS OPTIONS for close-up front or rear projection
and other applications
- SIX VIDEO and GRAPHICS INPUTS for virtually any video and data
source
- TWO EXPANSION PORTS for application specific signal
processing
- LAN, RS232 and USB ports for control and monitoring
The specifications and functionality of the product may change
without prior notice.
Downloaded from ProjectorsManual.com Manuals
C
SAFETY & WARNINGS
This user guide contains important information about safety
precautions and the set-up and use of the projector. Please read the
manual carefully before you operate the projector.
SAFETY
This device complies with relevant safety regulations for data
processing equipment for use in an office environment. Before using
the projector for the first time, please read the safety instructions
thoroughly.
WARNING
Use only the cables and cords supplied with the projector or original
replacement cables. Using other cables or cords may lead to
malfunction and permanent damage of the unit.
Always use 3-prong / grounded power cord to ensure proper
grounding of the unit. Never use 2-prong power cords, as this is
dangerous and could lead to electrical shock.
Never open the unit. The projector contains no user serviceable parts.
Refer all repairs to qualified personnel only.
Make sure that no objects enter into the vents and openings of the set.
Do not spill any liquids on the projector or into the vents or openings
of the unit.
Always remove lens cap before switching on the projector. If the lens
cap is not removed, it may melt due to the high energy light emitted
through the lens. Melting the lens cap may permanently damage the
surface of the projection lens.
Do not look into the projection lens when the projector is switched on.
The strong light may permanently damage sight.
Do not look into the laser beam when activated on the remote control.
Laser light may permanently damage sight. Do not point laser beam
on people.
Only place the projector on a stable surface, or mount it securely using
an approved ceiling-mount.
Do not drop the projector.
Always operate the projector horizontally, within the range of the
adjustable rear feet. Operating the unit in other positions may reduce
lamp life significantly, and may lead to overheating, resulting in
malfunctioning.
Always allow ample airflow through the projector. Never block any of
the air vents. Never cover the unit in any way while running. Allow for
sufficient distance to walls and ceilings to avoid overheating. Minimum
safety distance to any side of the unit is 50 cm / 20" in any direction.
CAUTION! Hot air is exhausted from the rear vent. Do not place
objects that are sensitive to heat nearer than 50cm / 20" to the
exhaust vent.
The projector is designed for indoor use only. Never operate the unit
outdoors.
4