Before Starting; Safety Test - Stiga SNOW POWER Instructions For Use Manual

EN
5.2

BEFORE STARTING

Fill the engine with oil before using.
Do not start the engine until filled with oil. The
engine can be seriously damaged without oil.
1. Place the machine on a level floor.
2. Loosen the dipstick (R) and read the oil level. See fig. 10.
3. The oil level shall be between the marks "ADD" and
"FULL". See fig. 10.
4. If necessary fill with oil up to the FULL mark. See fig. 10.
5. Use good quality oil marked A.P.I service SF, SG or SH.
Use SAE 5W30 oil. Use SAE 10W30 oil for temperatures
under -18° C.
Do not use SAE 10W40.
5.3 FILL UP THE PETROL TANK
Always use lead-free petrol. Oil-mixed 2-stroke petrol must
not be used.
NOTE! Bear in mind that ordinary lead-free petrol is
perishable; do not purchase more petrol than can be used
within thirty days.
Environmental petrol can be used, i.e. alkylate petrol. This
type of petrol has a composition that is less harmful for
people and nature.
Petrol is highly inflammable. Always store fuel in
containers that are made especially for this
purpose.
Store the petrol in a cool, well ventilated place –
not in the house. Store the petrol well out of reach
for children.
Only fill or top up with petrol outdoors, and never
smoke when filling or topping up. Fill with fuel
before starting the engine. Never remove the filler
cap or fill with petrol while the engine is running
or still warm.
Do not fill the petrol tank right to the top. After filling, screw
the filler cap on tightly and wipe up any spilt petrol.
5.4 STARTING THE ENGINE (WITHOUT
ELECTRICAL START)
1. Make sure the driving and auger clutch levers are
disengaged. See fig. 7.
2. Open the fuel cock (J).
3. Set the stop switch (I) to position "ON".
4. Put in the ignition key. Ensure it clicks tight. Do not turn
the key!
5. Turn the choke to position
not need the choke.
6. Press the rubber primer-start (M, fig. 8) 2 or 3 times.
Make sure the hole is covered when pressing the primer-
start. Note: Do not use this function when the engine is
warm.
7. Pull on the starter cord until you feel resistance. Start the
engine with a sharp pull.
8. When the engine starts, turn the choke anti-clockwise
until it is fully open.
Never run the machine indoors. The exhaust
fumes contain carbon monoxide, a very toxic gas.
44
ENGLISH
. Note: A warm engine does
Original instructions for use
5.5 STARTING THE ENGINE (WITH ELECTRICAL
START)
1. Attach the connecting cable to an earthed extension lead.
Then connect the extension lead to a 220/230 volt earthed
socket.
2. Make sure the driving and auger clutch levers are
disengaged. See fig. 7.
3. Open the fuel cock (J).
4. Set the stop switch (I) to position "ON".
5. Put in the ignition key. Ensure it clicks tight. Do not turn
the key!
6. Turn the choke to position
not need the choke.
7. Press the rubber primer-start (M, fig. 8) 2 or 3 times.
Make sure the hole is covered when pressing the primer-
start. Note: Do not use this function when the engine is
warm.
8. Starting the engine:
a. Press the start button to activate the starting motor.
b. When the engine starts, release the start button and
open the choke by slowly turning the choke lever anti-
clockwise to position
c. If the engine stutters, close the choke immediately and
gradually open it again.
d. First pull out the extension lead from the socket. Then
remove the extension lead from the engine.
Note: The electrical starting motor has overload
protection. The motor stops automatically when
overheated. It will not restart until it has cooled, which
takes about 5 - 10 minutes.
9. When the engine starts, turn the choke anti-clockwise
until it is fully open.
Never run the machine indoors. The exhaust
fumes contain carbon monoxide, a very toxic gas.
5.6

SAFETY TEST

This machine is equipped with several mechanical safety
systems, designed to keep the operator safe while using the
unit.
After starting and before use of the machine, it is essential
to perform the safety test below.
If the unit fails to operate as described, DO NOT operate it.
In this case, contact an authorised workshop for repair.
Auger test
1. The engine shall be running.
2. Press down the auger lever and the auger shall rotate.
3. Release the auger lever and the auger shall stop within 5
seconds.
Drive test
1. The engine shall be running and the gear lever in 1st gear
alt. the speed lever in low speed.
2. Press down the driving lever and the unit shall move.
3. Release the driving lever and the unit shall stop.
. Note: A warm engine does
.