Video Config - Panasonic BT-3DL2550E Operating Instructions Manual

Main Menu
(continued)

VIDEO CONFIG

Sub menu Setting
GAMMA
STANDARD
*1*2
SELECT
STDIO/PST
FILM
COLOR SPACE
SMPTE-C (EX)
*7*8
EBU (EX)
SMPTE-C
EBU
ITU-709
WIDE1
WIDE2
WIDE3
COLOR TEMP.
USER0 - 63
D93
D65
D56
VAR1
VAR2
VAR3
SHARPNESS
HIGH
*2
LOW
MODE
*1 Changes are not reflected to a still image in the main window in the split-screen display of the "TWO WINDOW" function.
*2 These functions are not available when "RGB-COMP." under "YP
the "INPUT SELECT" menu (
is selected. Selecting WIDE1 to 3 for "COLOR SPACE" produces the gamma curve fixed to that "COLOR SPACE."
*3 The following sharpness values are available and the settings for the selected input signal is displayed.
Adjustment status during selection appears at the bottom right of the screen.
1) VIDEO system input (VIDEO) (the factory defaults are SHARPNESS MODE: LOW)
2) HD for any other input (the factory defaults are SHARPNESS MODE: HIGH).
3) SD for any other input (the factory defaults are SHARPNESS MODE: LOW).
*4 Selecting "VAR1", "VAR2" and "VAR3" engages the WB adjustment mode (
*5 Procedure for selecting USER 0 - 63:
1) Press [ENTER] ("USER" changes to blue).
*6 An asterisk (*) is displayed after the color temperature value in 3D mode. (Example display: D65*) This
indicates that it is an adjusted value for when using 3D Polarized Eyewear.
*7 Factory default setting: SMPTE-C (U.S.A. and Canada), EBU (other countries)
*8 The SDI1 signal and SDI2 signal (displayed when "COMPARISON" is selected in SIMUL MODE) are set to the
same color space.
*9 As the red reproduction of this monitor is truer to the original than previous models (exc. BT-LH2550) red
appears darker. Used when rendering colors that have a softer shade of red.
Description
Selects gamma curve. The gamma curve in the sub-window can be
set in the split-screen display and sub-window display (single screen)
of the "TWO WINDOW" function.
<STANDARD>Standard mode
<STDIO/PST>Color emphasis mode (a mode that approximates CRT
<FILM>
The
selected.
Sets the color space. The color space in the sub-window can be set in
the split-screen display and sub-window display (single screen) of the
"TWO WINDOW" function.
<SMPTE-C (EX)> Redness changed from <SMPTE-C> mode.
<EBU (EX)>
<SMPTE-C> SMPTE-C standard
<EBU>
<ITU-709>
<WIDE1>
<WIDE2>
<WIDE3>
*5*6
Selects color temperature. Both the main window and sub-window can
*6
be set up in the split-screen display of the "TWO WINDOW" function.
*6
<USER 0 - 63>
*6
<D93> Equivalent to a color temperature of 9,300K
<D65> Equivalent to a color temperature of 6,500K
<D56> Equivalent to a color temperature of 5,600K
<VAR1> WB adjustment mode
<VAR3> WB adjustment mode
USER20 is approximately 5,000 K and USER33 is approximately 6,300 K.
*3
Selects the width of outline correction edge. Both the main window
and sub-window can be set up in the split-screen display of the "TWO
WINDOW" function.
<HIGH> Thin edge
page 40). The gamma curve is set to STANDARD when "RGB-COMP." or "DVI-COMP."
Underlined values indicate factory defaults.
display capability suitable for studio or postproduction
application)
Film mode (For VARICAM use)
mark appears at the top left of the screen when "FILM" is
Redness changed from <EBU> mode.
EBU standard
ITU-R BT. 709 standard
Sets the gamma curve to 2.2 in wide color gamut (using
Adobe color space) mode.
Sets the gamma curve to 1.8 in wide color gamut (using
Adobe color space) mode.
Sets the gamma curve to 2.6 in wide color gamut (using
D-Cinema color space) mode.
Adjustable settings 0 - 63 (equivalent to a color
temperature range of 3,000 - 9,300K)
*4
<VAR2> WB adjustment mode
*4
<LOW> Wide edge
P /RGB" or "DVI-COMP." under "DVI-D" is selected in
B R
2) Use [ , ] to select 0 - 63 and press [ENTER].
*9
page 31).
*9
*4
29