Oven Light - KitchenAid YKFEG500ESS User Instructions

OVEN CAVITY
Use AquaLift ® Technology regularly to clean oven spills.
Do not use oven cleaners.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
Cleaning Method:
Clean cycle:
See "Clean Cycle" first.

Oven Light

The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the Off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer
to the warranty page in this manual and scan the code there with your mobile device, or visit http://www.kitchenaid.ca.
Contact us by mail with any questions or concerns at the address below:
In Canada:
KitchenAid Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
PROBLEM
Nothing will operate
Cooktop will not operate
Excessive heat around
cookware on cooktop
Cooktop cooking results
not what expected
Cooktop element cycles on
and off on High setting
Oven will not operate
Oven temperature too high
or too low
Oven indicator lights flash
PROBLEM SOLVER
POSSIBLE CAUSES AND/OR SOLUTIONS
Power supply cord is unplugged - Plug into a grounded outlet.
Energy Save is active, and the display is blank - Press any key on the control to display the time of
day. See the "Electronic Oven Controls" section for more information.
Household fuse is blown, or a circuit breaker is tripped - Replace the fuse or reset the circuit breaker.
If the problem continues, call an electrician.
The control displays an F9 or F9 E0 error code - The electrical outlet in the home may be miswired.
Contact a qualified electrician to verify the electrical supply.
The control knob is not set correctly - Push in knob before turning to a setting.
On ceramic glass models, the oven control lockout is set - See the "Control Lock" keypad feature in
the "Feature Guide" section.
Cookware is not the proper size - Use cookware about the same size as the surface cooking area,
element or surface burner. Cookware should not extend more than ¹⁄₂" (1.3 cm) outside the cooking area.
Control knob set to incorrect heat level - See the "Cooktop Use" section.
Range is not level - Level the range. See the Installation Instructions.
Element cycling due to a temperature limiter - This is normal operation. The element may cycle on
and off to keep the cooktop from overheating.
Delay Start is set - See the "Cook Time" section.
Control Lock is on - Press and hold the "0" key for 3 seconds to unlock.
Control is in Demo Mode - See the "Electronic Oven Controls" section. Demo Mode is used for display
models in a showroom.
Electronic oven control set incorrectly - See the "Electronic Oven Controls" section.
Oven temperature needs adjustment - See "Oven Temperature Control" in the "Electronic Oven
Controls" section.
Power to range is turned on or restored - See "Control Display" in the "Electronic Oven Controls"
section. If the indicator lights keep flashing, call for service. See the "Warranty" section for contact
information.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb by turning clockwise.
5. Replace bulb cover by turning clockwise.
6. Plug in range or reconnect power.
Appliance Outlets
The 120-volt appliance outlet located on the control console may
be used to run portable appliances placed on countertops beside
the range.
The outlet operates independently and is not affected by range
control settings.
NOTE: Do not place portable appliances on the cooktop. Damage
to the portable appliance could result if the cooktop is hot.
Appliance Outlet Circuit Breaker:
The circuit breaker for the appliance outlet on your range is located
next to the outlet. It is rated for 12 amps.
If the circuit breaker trips, it can be reset by pressing the switch. A
delay of several minutes may be required for the circuit breaker to
cool before it will reset.
17