Subscribe to Our Youtube Channel
Related Manuals for ACO Familio PRO
Summary of Contents for ACO Familio PRO
- Page 1 OPERATING INSTRUCTIONS FOR VIDEO INTERPHONE SYSTEM Familio PRO 62-002 Suchy Las, ul. Diamentowa 7, tel./fax +48 61 843 93 72 www.aco.com.pl/en...
-
Page 2: Table Of Contents
Selecting a connection with other monitors (intercom) or with the Panel.........6 Opening the door and preview control..................7 Bus status signalling........................7 PRO - I/O module........................7 Connecting the panel to a computer and panel configuration with the Familio PRO application..........................8 Restoring factory-defined codes and adding/deleting keycards..........9 SYSTEM CONNECTION AND ASSEMBLY..................9 Panel............................11... -
Page 3: General Information
GETTING ACQUAINTED WITH THESE INSTRUCTIONS 1 GENERAL INFORMATION The Familio Pro digital video interphone system is designed to be used for single-family and multi- family solutions, where transmission of a video signal accompanied by an audio signal is required. The system also allows one to establish internal connections (intercom) between monitors. -
Page 4: Echnical Parameters
Room required for flush mounting of the panel 286 x 90 mm (H x W) Communication with a PC USB (CDN-USB and the Familio PRO application) Maximum number of different opening codes 4 (1 for every user + 1 administrator's code) ... -
Page 5: Power-Supply Unit
Connector type RJ45 socket / ARK-type screwed terminal connectors Operation type monostable / bistable Type of additional call Normally open (NO) 2.4 Power-supply unit Power-supply voltage 100 – 240VAC 1.0A 50/60Hz Output voltage 15VDC ±5% ... -
Page 6: Monitor Configuration
3.3 Monitor configuration Fig. 3.1 Front view of the monitor Call volume adjustment - touch + or – in the stand-by mode Sound tone adjustment - touch the F2 icon during volume adjustment and select a ring tone Screen brightness adjustment - touch the monitor icon in the stand-by mode, then use + or –... -
Page 7: Opening The Door And Preview Control
3.5 Opening the door and preview control The door is opened (typically by activating the electric strike) once the key icon is touched. The preview is switched on, once the monitor icon is touched. Both functions are available on condition that other users are not receiving calls. -
Page 8: Connecting The Panel To A Computer And Panel Configuration With The Familio Pro Application
3.8 Connecting the panel to a computer and panel configuration with the Familio PRO application In order to connect the panel to a PC computer and configure it with the Familio PRO application, the optional CDN-USB cable should be used. The free application should be downloaded from the address: www.aco.com.pl. -
Page 9: Restoring Factory-Defined Codes And Adding/Deleting Keycards
It is absolutely necessary to prepare a back-up copy of the panel settings by means of the Familio PRO application (as described above). 3.9 Restoring factory-defined codes and adding/deleting keycards It is possible to restore factory-defined opening codes and add/delete proximity keycards if "Block restoration of factory-defined codes and keycards"... - Page 10 RJ45 plugs are correctly crimped and that there are not short- circuits between cable conductors. Fig. 4.2 Distribution of lines in RJ45 connector Fig. 4.3 presents the basic connection diagram of the Familio PRO system that uses one monitor. Fig. 4.3 Basic connections of the Familio PRO system -10-...
-
Page 11: Panel
ATTENTION! To ensure proper functioning and operation safety, the installed panel should be connected to a ground line. The "ground" terminal on the panel body should be connected to an appropriate protective installation (PE) – this concerns a metal box. 4.1 Panel Fig. - Page 12 NO input for additional opening INPUT Power supply ground and reference potential for the NO input LINE Signal line Power supply voltage input Electric strike control, "-" potential ELOCK* Electric strike control, “+” potential Electric strike power supply, “+” potential EL POW Electric strike power supply, “-”...
-
Page 13: Power-Supply Unit
4.2 Power-supply unit ATTENTION! To ensure proper functioning and operation safety, the power-supply unit should be connected to 230V grid with an appropriate three-core cable and the PE terminal must unconditionally be connected. The connection to 230V grid must be made by a qualified electrician. The work involves exposure to voltages that are dangerous for health and life! The power-supply unit is designed to be mounted on a DIN 35 mm rail or flush-mounted. - Page 14 The video terminator should be switched on in each monitor with switch 6 (ON position). It is required to be off only in special cases, discussed in the diagrams catalogue. The 10k line terminator (switch 5) should be switched on ONLY in the monitor that is furthest removed from the panel.
-
Page 15: I/O Module
To mount the monitor, slide it onto the relevant catches (1) in the plate and move it down to snap (2) (fig. 4.11). Fig. 4.11 Mounting of the monitor 4.4 I/O module Fig. 4.12 Connection of the I/O module: a) serial connection to the system bus, b) bus-independent connection The I/O module can be connected to the system at any place. -
Page 16: Most Frequent Problems
I/O module during a call. signal line. Examples of installations diagrams available in the diagrams catalogue at the address www.aco.com.pl. 6 MAINTAINING THE SYSTEM CLEAN The panel and the monitor can be cleaned with humid antistatic cloth. More persistent dirt can be removed from the panel with stainless steel cleaning agents (e.g.
Need help?
Do you have a question about the Familio PRO and is the answer not in the manual?
Questions and answers