Related Manuals for CDA CD 66
Summary of Contents for CDA CD 66
- Page 1 Ceramic Hobs CD 66 Users Operating Instructions Before operating this hob, please read these instructions carefully...
-
Page 2: Tips For The User
Dear Customer Thank you for choosing one of our products. The warnings and tips given below are intended to protect your safety and that of others. They will also help you make the most of your appliance. Keep this booklet in a safe place. It will be useful if you, or anyone else, have any doubts about use of the appliance. -
Page 3: Ce Declaration Of Conformity
IMPORTANT WARNINGS AND TIPS When unpacking the appliance make sure that it is not damaged. If you have any doubts, do not use the appliance but consult your supplier or an engineer. The packing materials (plastic bags, expanded polystyrene, nails, bands etc.) must not be left within easy reach of children, because they are a possible source of dan- ger. - Page 4 Technical Data Quick-light hotplate Ø 145 - 1200 W Quick-light hotplate Ø 180 - 1700 W Quick-light hotplate Ø 195 - 1900 W “ON” indicator light Hotplate and residual heat indicator Voltage 230 V~ 50 Hz Maximum absorbed power 6,0 kW DIMENSIONS General Dimensions Width...
- Page 5 Fitting your hob Minimum distance of hob to back wall 50 mm. Minimum distance of hob from any vertical surface either side of the hob 50 mm. Minimum height of a cabinet directly above hob if not fitting a hood 900 mm. Minimum of 650 mm from the hob to a cooker hood.
- Page 6 HOW TO INSTALL YOUR HOB 1. The hob requires a space in the kitchen work surface as shown in the diagram (Fig. 2) below: Figure 2 2. Apply the adhesive seal around the edge of the hob ensuring that the ends do not over lap or leave a space.
- Page 7 3. Place the hob in the work top cut out and secure it in position by using the brackets as indicated in Fig. 4 - (3 cm work top) or Fig. 5 - (4 cm work top). Figure 4 Figure 5 NOTE: A partition should be fitted a minimum of 4 cm below the base of the hob if the cupboard is to be used for storage.
- Page 8 Electric Supply Requirements WARNING! double pole switch must be provided no further than 2 metres from the This appliance must be earthed. appliance to the electrical supply. Your hob must be installed by a quali- All supply current and earth conductors fied electrician in line with all electrical must be able to withstand an ambient and installation requirements published...
- Page 9 How Your Quick light Hob Operates Figure 8 The ceramic surface of the hob allows a fast transmission of heat in the vertical direction, from the heating elements underneath the ceramic glass to the pans set on it. The heat does not spread in the horizontal direction, so that the glass stays “cool” only a few centimeters from the cooking plate.
- Page 10 The ceramic hob has the temperature control knobs located on the right hand side of the hob. These knobs are wired as follows (Fig. 9): Rear right plate Rear left plate Front left plate Front right plate The hob is provided with a signal lamp (5) which lights up when the hob is switched The hob also features 4 warning lamps (6) which are wired to the corresponding plate.
- Page 11 Use of Ceramic Hob Before you switch the hob on make QUICK-LIGHT HOTPLATE sure that it is clean. Incorporating 3 heating elements you To switch a cooking plate on you must can control and light up all together or turn the relevant control knob anti- separately by a 7 position switch.
-
Page 12: Cooking Hints
COOKING HINTS: To reduce the cooking time, you can turn the control knob to the max when you switch the plate on. After a short time you will set the control knob to the required position for the cooking. You should use pots and pans with flat bases. The diameter of the pan should match that of the cooking plate (or be slightly bigger) to make the most of the energy. -
Page 13: Safety Hints
Safety Hints Figure 13 1. Never put aluminium foil or plastic materials on the ceramic surface when the hob is hot. DISTORTED 2. Make sure that the hob is clean before PANBASE you use it. WRONG 3. Remember that the plates will remain hot for approximately half an hour after the plate has been switched off. - Page 14 Cookware It is very important that the pans used on the hobs are made of a suitable material and have the correct base as follows: The base should be flat and smooth. Any rough part on the pan base could scratch the hob surface. Choose pans which are the same size as the hotplates and with bases that are as non reflective as possible.
-
Page 15: Cleaning Your Hob
Cleaning Your Hob Before you begin cleaning make sure that the hob is switched off. Remove spillages and other types of incrustations. Dust or food particles can be removed with a damp cloth. If you use a detergent, please make sure that it is not abrasive or scouring. Abrasive or scouring powders can damage the glass surface of the hob. -
Page 16: Ceramic Hobs
Ceramic Hobs 1101406 ß5...