Page 1
O2iTC23/O2i605CM/O2i607CM/O2i562/O2i675/O2i695 ® Intensifier IP Full HD 1080 Specialty IP Camera...
Page 2
’ ’ Directions Be careful not to cause any physical damage by dropping or throwing the camera. Especially keep the device out of reach from children. Do not disassemble the camera. No after service is assumed when disassembled. Use only power adapters compatible with the unit. Be careful to prevent moisture or water penetration into the unit.
’ ’ 1. Introduction 1.1. Overview This product is a multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video up to 1,080P and audio data. Remote clients can connect to IP Camera for the real time video/audio data through various client solutions running on PC or smart device.
’ ’ 1.2. Specifications Camera Image sensor Progressive scan 1/3 inch CMOS 2M pixels Full resolution 1,920 x 1,080 pixels (Full HD) Sync System Internal Lens 2.9mm fixed (3.6mm for O2i562) Day & Night AUTO, DAY, NIGHT Sensitivity Intensifier Max – 0.0005 Lux Back Light Compensation ON / OFF White Balance...
Page 7
Network Protocol - RTP, RTSP, SDP, HTTP, SMTP, FTP, DHCP, UPnP - NTP, DNS, DynDNS Dynamic IP Speco DDNS (free of charge) - User ID & Password protection, IP address filtering Security - Digest Authentication, User Access Log - RTSP streaming with proprietary format for control information...
’ ’ 2. Product Description 2.1. Contents The product package contains the following contains the following : Contents Description Remarks Remarks Camera Main unit and camera unit Main unit and camera unit Screws (1 type) Screws (1 type) Anchors (1 type) Anchors (1 type) Accessories L-type wrench...
’ ’ 2.3.3. Front and Rear view of Main Unit Main Unit Cable bracket screw hole Description Description Line Output Line Output Ground MIC/Line Input Line Input Figure 2-3. Front view Relay Output Relay Output Relay Output Output Sensor Input Sensor Input (+) Connect Connect Camera...
’ ’ 2.4. Functional Description Power : Power input for supplying Power input for supplying 12V DC power. Caution : If camera is powered by PoE, do not plug in DC Jack with active DC power is powered by PoE, do not plug in DC Jack with active DC power into DC power connector.
Page 12
’ ’ Sensor Input Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor, heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to “Sensor Input”. The sensor type (NC/NO) can be set in admin page. Multiple sensor devices can be connected in parallel. NO/NC Type Open Collector Type Photo Coupler...
’ ’ 3. On Site Installation Use cables and conduits that are suitable for the installation. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product.
’ ’ 4. Getting Started 4.1. PC Requirements Audio/Video streaming data received from the camera can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: ITEM Minimum Requirement Recommended Specification Intel Core i3 3Ghz Intel Core i7 Main Memory Operating System...
’ ’ 4.2. Quick Installation Guide 4.2.1. Connect PC and camera to network. to network. 1. Prepare a PC to run programs for the installation and video connection Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to (PC is needed to assign IP address to camera) 2.
’ ’ Click on the field in (3) for sorting and rearranging the list. for sorting and rearranging the list. Select network mode that best suits from the drop down list in Select network mode that best suits from the drop down list in (5). You can choose either Static or .
Page 17
Active-X module. Most convenient way of X module. Most convenient way of installing the Active-X module is installing X module is installing Speco-NVR which is available from the CD or our m the CD or our web site.
’ ’ 4.2.4. Additional settings through connection to the Admin Page All parameters of the camera are factory default out of the box. For a more sophisticated target application, parameters need to be changed through the admin page. The admin page can be connected through “http://IP_Address:Port_Number/admin.htm”...
’ ’ 5. Troubleshooting 5.1. No power is applied In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af) In case of DC adapter If PoE is not applied, the power and network connection should be made through separate cables.
’ ’ 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) If “Reply from ~” message is returned ( in the figure below), the network connection is in normal ①...
’ ’ 5.3. Technical Assistance If you need any technical assistance, please contact If you need any technical assistance, please contact technical support. For immediate service please . For immediate service please provide the following information. Model name 1 . 1 . 1 . 1 . MAC address and Registration number MAC address and Registration number 2 .
’ ’ Appendix A – Important Notice in Exchanging SD Card (Micro SD) SD Card is a non-volatile memory device for storing video and audio data on the product. Note that continuous recording to the SD Card will cause the memory cell to wear out, eventually resulting in failure. When you plug out the SD Card for replacement or other purpose, follow the steps below in order to prevent data loss or crash of the SD Card.