Toro 03170 Operator's Manual page 7

• Do not operate on a side hill that is too steep. A
rollover may occur before losing traction.
• Model 03171-The slope angle at which the machine
will tip is dependent on many factors. Among these
are mowing conditions such as wet or undulating
terrain, speed (especially in turns), position of the
cutting units (with the Sidewinder), tire pressure,
and operator experience. At side hill angles of 15
degrees or less, the risk of a rollover is low. As the
slope angle increases to a recommended maximum
limit of 20 degrees, the risk of a rollover increases to
a moderate level. Do not exceed a 20 degree side
hill slope angle because the risk of a rollover and
serious injury or death is very high.
• Model 03170-The slope angle at which the machine
will tip is dependent on many factors. Among these
are mowing conditions such as wet or undulating
terrain, speed (especially in turns), position of the
cutting units, tire pressure, and operator experience.
At side hill angles of 20 degrees or less, the risk of
a rollover is low. As the slope angle increases to a
recommended maximum limit of 25 degrees, the risk
of a rollover increases to a moderate level. Do not
exceed a 25 degree side hill slope angle because
the risk of a rollover and serious injury or death
is very high.
• For steering control, lower the cutting units when
going down slopes.
• Avoid sudden stops and starts.
• Use the reverse pedal for braking.
• Watch for traffic when near or crossing roads.
Always yield the right-of-way.
• Raise the cutting units when driving from one work
area to another.
• Do not touch the engine, muffler, exhaust pipe, or
hydraulic tank while the engine is running or soon
after it has stopped because these areas could be hot
enough to cause burns.
• This machine is not designed or equipped for
on-road use and is a slow-moving vehicle. If you
must cross or travel on a public road, you should
be aware of and comply with local regulations, such
as required lights, slow moving vehicle signs, and
reflectors.
• The grass baskets must be in place during operation
of the cylinders/reels or thatchers for maximum
safety. Shut the engine off before emptying the
baskets.
• When a person or pet appears unexpectedly in or
near the mowing area, stop mowing. Careless
operation, combined with terrain angles, ricochets,
or improperly positioned guards can lead to thrown
object injuries. Do not resume mowing until the
area is cleared.
Maintenance and Storage
• Before servicing or making adjustments, stop the
engine and remove the ignition key.
• Ensure that the entire machine is properly maintained
and in good operating condition. Frequently check
all nuts, bolts, screws, and hydraulic fittings.
• Make sure all hydraulic line connectors are tight and
all hydraulic hoses and lines are in good condition
before applying pressure to the system.
• Keep your body and hands away from pin hole
leaks or nozzles that eject hydraulic fluid under high
pressure. Use paper or cardboard, not your hands,
to search for leaks. Hydraulic fluid escaping under
pressure can have sufficient force to penetrate the
skin and cause serious injury. If fluid is injected into
the skin it must be surgically removed within a few
hours by a doctor familiar with this form of injury
or gangrene may result.
• Check all fuel lines for tightness and wear on a
regular basis. Tighten or repair them as needed.
• Before disconnecting or performing any work on
the hydraulic system, all pressure in the system must
be relieved by stopping the engine and lowering the
cutting units to the ground.
• If the engine must be running to perform a
maintenance adjustment, keep hands, feet, clothing,
and any parts of the body away from the cutting
units, attachments, and any moving parts. Keep
everyone away.
• Do not overspeed the engine by changing governor
settings. To ensure safety and accuracy, have an
Authorized Toro Distributor check the maximum
engine speed with a tachometer.
• The engine must be shut off before checking the oil
or adding oil to the crankcase.
• If major repairs are ever needed or if assistance is
desired, contact an Authorized Toro Distributor.
• To ensure optimum performance and continued
safety certification of the machine, use only
genuine Toro replacement parts and accessories.
Replacement parts and accessories made by other
manufacturers could be dangerous, and such use
could void the product warranty.
7