Toro Reelmaster 3100-D Series Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Cutter
  5. 03200 Reelmaster 3100-D
  6. Operator's manual
Toro Reelmaster 3100-D Series Operator's Manual

Toro Reelmaster 3100-D Series Operator's Manual

27-inch verticutter dpa cutting unit, 03203-serial no. 400000000 and up
Hide thumbs Also See for Reelmaster 3100-D Series:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Instruction and Installation Manual
Register at www.Toro.com.
Original Instructions (EN)
27-inch Verticutter
Reelmaster
®
3100-D Series DPA Cutting Unit
Model No. 03203—Serial No. 400000000 and Up
Form No. 3407-799 Rev A
*3407-799* A

Advertisement

Table of Contents
loading

Related Manuals for Toro Reelmaster 3100-D Series

Summary of Contents for Toro Reelmaster 3100-D Series

  • Page 1 Form No. 3407-799 Rev A 27-inch Verticutter Reelmaster ® 3100-D Series DPA Cutting Unit Model No. 03203—Serial No. 400000000 and Up *3407-799* A Register at www.Toro.com. Original Instructions (EN)

  • Page 2: Table Of Contents

    Safety and Instructional Decals ......... 3 Setup ................4 You may contact Toro directly at www.Toro.com for product 1 Inspecting the Verticutter........5 safety and operation training materials, accessory information, 2 Installing the Transport Rollers ....... 5 help finding a dealer, or to register your product.

  • Page 3: Safety

    • To ensure optimum performance and continued safety influence of drugs or alcohol. certification of the machine, use only genuine Toro • Keep all shields and safety devices in place. If a shield, a replacement parts and accessories. Replacement parts...

  • Page 4: Setup

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Verticutter Inspect the verticutter. Transport roller assembly Install the transport rollers. Cotter pin O-ring Install the O-ring and the grease fitting. Grease fitting –...

  • Page 5: Inspecting The Verticutter

    Note: Determine the left and right sides of the machine from the normal operating position. Note: Whenever the verticutter has to be tipped to expose the verticutter blades, use the kick stand (supplied with Installing the Transport Rollers traction unit) (Figure Parts needed for this procedure: Transport roller assembly...

  • Page 6: Installing The O-Ring And The Grease Fitting

    Installing the O-ring and the Grease Fitting Parts needed for this procedure: O-ring Grease fitting G028407 Procedure g028407 The grease fitting must be installed on the reel motor side of Figure 6 the verticutter. Use the following diagram to determine the position of each reel motor (Figure 1.

  • Page 7: Adjusting The Blade Depth

    Adjusting the Blade Depth Adjusting the Rear Grass Shield No Parts Required No Parts Required Procedure Procedure Note: The maximum recommended blade penetration depth is 6 mm (1/4 inch). Note: When operating in turf conditions where much debris 1. Place the verticutter reel on a level surface. or unusually heavy thatch is encountered, open the rear discharge shield to help allow the debris to discharge from 2.

  • Page 8: Adjusting The Transport Rollers

    Mounting the Verticutter Reel No Parts Required Procedure Important: When lowering the verticutter reels, care must be taken to prevent damage to the reel blades due to contact with a concrete floor or a paved surface. Lower the transport rollers before lowering the verticuttiers to g012271 Figure 10 a concrete floor or a paved surface.

  • Page 9: Product Overview

    Product Overview Operation Note: Determine the left and right sides of the machine Specifications from the normal operating position. Net weight 56 kg (124 lb) Training Period Before operating the verticutter reels, evaluate the performance of the reel at the desired setting. Operate in a clear, unused area to determine if the desired results will be achieved.

  • Page 10: Maintenance

    Maintenance with a light coating of grease to simplify the assembly (Figure 13). Lubricating the Verticutter Each verticutter has 5 grease fittings (Figure 12) that must be lubricated weekly with No. 2 lithium grease. The lubrication points are the front roller (2), the rear roller (2), and the reel motor splines (1).

  • Page 11: Installing The Verticutter Blades

    Installing the Verticutter Blades 1. Assemble a reel blade (Figure 14). 2. Assemble a large spacer. 3. Do not invert the reel blades when reassembling on reel shaft. Note: If the blades are inverted, the blades that are in use, (rounded) will be mixed with the sharp ends of the blades which were not in use.
  • Page 12 g007790 Figure 15 6. Bearing nut 1. Rebuild kit (Part No. 114–5430) 2. Rebuild tool kit (Part No. 115–0803) 7. Inner seal tool 3. Inner seal 8. Washer 4. Bearing 9. Bearing/outer seal tool 5. Outer seal...
  • Page 13 Notes:...
  • Page 14 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
  • Page 15 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

Table of Contents