Table of Contents
Advertisement
Calling the control panel on the fixed line
Caution! - To answer incoming calls on the PSTN line, the guide message
N° 7 must be present (see paragraph 6.2.2); without this message, the
control panel ignores the call.
To call the control panel, proceed as follows:
01. Dial the control panel telephone number.
02. Interrupt the call after the second ring.
TABLE A
0 #
0 ✱ 1 #
0 ✱ 2 #
0 ✱ 0 #
2 0 ✱ 1 #
2 0 ✱ 0 #
2 0 #
2 1 ✱ 1 #
2 1 ✱ 0 #
2 1 #
X X ✱ 1 #
X X ✱ 0 #
Calling the control panel on GSM module (HSCU1GC only)
The GSM module responds immediately to the incoming calls only if the called
ID is recognised (the telephone must be enabled to send its own ID). It is also
possible to avoid sending the user code, by enabling direct access for specific
caller numbers (see PHONE BOOK – DIRECT ACCESS).
If the caller phone does not send its own number, or if the number is not
enabled for direct access, refer to the previous procedure "Calling the control
panel on the fixed line" for calling the GSM module.
9.2.10 - User called by the control panel
In the event of an alarm, the control panel makes the envisaged telephone calls.
Those called can interact with the control panel, for example to disarm it by
entry of the command described in Table A.
Those called by the control panel can interrupt the cycle of envisaged calls
(consecutive); to stop the calls, listen to the message and the end confirmation
beep and then press the # key on the telephone.
9.2.11 - Remote listening
Both when called by the control panel and when the user calls the control pan-
el, during connection on the PSTN fixed line, the user can listen to the environ-
mental noise captured by the control panel microphone.
To enable this function, press ✱ on the telephone. Press ✱ again to stop listen-
ing and proceed with sending any commands as required. If no operation is
performed, the call is terminated after 60 seconds from ending the remote lis-
tening function.
9.2.12 - Hands free conversation
(HSCU1GC and HSCU1G only, with control panel disarmed)
Both when called by the control panel and when the user calls the control pan-
el, during connection on the GSM network, the user can set communication to
hands-free mode from the microphone and loudspeaker of the control panel.
To enable this function, press ✱ on the telephone. Press ✱ again to stop listen-
ing and proceed with sending any commands as required. If no operation is
performed, the call is terminated after 60 seconds from ending the remote lis-
tening function.
A telephone call can also be initiated using the built-in GSM. To enable this
function, proceed as follows:
01. Press the key (
) to connect.
02. Dial the number to be called and press OK to confirm:
03. To terminate the call, press ESC or the key (
Caution! - The control panel HSCU1G enables the call, but the user must wait
for the GSM module to switch on and connect to the network.
9.2.13 - Remote modifications to stored telephone numbers
(HSCU1GC only)
It is possible to change the phone numbers in the phone book by means of an
SMS message sent from a telephone memorised and enabled for direct
access. To perform this operation, write the SMS message without spaces as
follows: A[old number to replace]A[new number to enter]
for example: A333555666A333777888
34
34
Querying control panel status with vocal reply
Total arming and vocal confirmation
Partial arming (zones A+B only) and vocal confirmation
Disarming and vocal confirmation
(*) Activation of relay N° 1
(*) Deactivation of relay N° 1
Check of status of relay N°1 (3 Beeps = relay active; 1 Beep = relay deactivated)
(*) Activation of relay N° 2
(*) Deactivation of relay N° 2
Check of status of relay N°2 (3 Beeps = relay active; 1 Beep = relay deactivated)
Delivery of radio control ON command to receiver N° XX (enter digit from 1 to 16)
Delivery of radio control OFF command to receiver N° XX (enter digit from 1 to 16)
(*) Note - the command sent with a telephone call has priority over other envisaged commands; for example timed set-
tings of relay 1.
).
03. Call again immediately. the control panel answers with vocal message N° 7.
04. After listening to the message, enter the user code on the telephone key-
pad, followed by the symbol #.
05. Then enter the command required (see Table A).
The control panel sends the following confirmation SMS message:
"CHANGE MADE *333777888*"
9.2.14 - Other functions on the GSM module
The control panels with GSM module offer other automatic functions (if pro-
grammed by the installer), such as:
• SMS notifying of absence and return of mains power (HSCU1GC only).
• SMS for periodic notification that the control panel is operating correctly.
• SMS notifying of SIM expiry.
• SMS notifying of low battery charge in devices.
• SMS notifying of control panel arming/disarming.
9.2.15 - Residual credit on SIM
Press
to make an automatic call to the service centre of the telephone oper-
ator and listen to an automatic message informing the user of the residual cred-
it on the SIM card (the function must be configured accordingly (see 6.2.1).
Advertisement
Table of Contents
