Table of Contents
Advertisement
EXAMPLE 1
(1)
1 6 / 0 5 / 0 7 1 9 : 5 9
I N S T A L
(2)
EXAMPLE 2
(2)
(1)
1 6 / 0 5 / 0 7 0 9 : 3 2 V
M A R C O
(4)
EXAMPLE 3
(1)
1 6 / 0 5 / 0 7 1 8 : 2 0
I N S E R
(2)
9.2.7 - Timed program
The control panels HSCU1GC and HSCU1C are equipped with 1 relay output
whi ch can be used to control electrical appliances. Activation can be via a com-
mand sent by means of a telephone call (see 9.2.9) or automatically at a set ti -
me. In this case the activation start and end time can be programmed as follows:
01. With the control panel disarmed, press ESC.
02. The first line of the display shows TIME ON : 00:00; the second line dis-
plays TIME OFF: 00:00.
03. Use the numerical keys to enter the required times and press OK to con-
firm.
After programming the times, the function is enabled by pressing the UP arrow
key [ ] in the main menu when the control panel is disarmed. The top left cor-
ner of the display shows the symbol "H" to indicate that the timed program is
active and the relay output will therefore be activated every day at the set times.
To disable the timed function press the DOWN arrow key [ ] (the "H" symbol
disappears from display).
9.2.8 - Remote assistance
If the installer has the specific telephone modem, a PC and relative software, the
control panel can be controlled at a distance to analyse and solve any problems.
EXAMPLE 1 - key
n°
Display
(1)
(1)
(2)
INSTALL
USER
NO PSTN LINE
NO GSM NETWORK
MAINS FAILURE
CHANGE NUM.
GSM CHECK
EXAMPLE 2 - key
n°
Display
(1)
(3)
(1)
(2)
(3)
V
OK
S
D
(5)
(4)
(name)
CONTACT ID
INSTALLER
CUST. SERV.
(5)
OK
KO:
OC
NO:
EXAMPLE 3 - key
n°
Display
(1)
(1)
(2)
ARM
IN A (or B or C)
DISARM
T E L 0 1
EXT AL
OPEN
(3)
TAMPER
ALARM
PROGR.
SUPERV
SCAN
BATT
DELETE
EXCLUD
INCLUD
Xxxxx (label)
(3)
TEL
COD
DET
WIR
USER
INSTAL
REMOTE
Meaning
date/time of event
access to menu with installer code
access to menu with user code
no connection to PSTN telephone line
no connection to GSM network
no power supply from mains
modification via SMS of a phone number in phone book
GSM activation-deactivation procedure
Meaning
date/time of call
outgoing call
incoming call
vocal message
SMS message
message in digital protocol
name of call recipient (stored in PHONE BOOK)
call to alarm receiving centre
remote assistance call
call from service centre
call successful
call failed
call failed as engaged
call failed as no answer
Meaning
date/time of event
total arming
partial arming
disarming
external alarm
door/window open
tampering
alarm
programming
supervision failure
radio disturbance
battery discharged
deletion
out of service
in service
name assigned to peripheral
remote control
keypad code
sensor/detector
wired input
access to menu with user code
access to menu with installer code
intervention via remote telephone
The remote control must be activated by the user by pressing the holding the
key for more than 5 seconds so that the control panel makes the call the
telephone number entered by the installer. During connection, the user must
avoid intervening on the control panel keypad to avoid any conflict. The user
can still monitor operations in progress on display.
Warnings for the installer - A special access code can be configured (in the
Remote management menu) to enable automatic access by the installer to the
control panel. However the installer must bear in mind that this operation can
be performed without the presence of the user and that it causes system deac-
tivation (though only temporary). As this is the specific responsibility of the
installer, a previous agreement is recommended between the installer and user
to authorise use of the remote assistance provision without the user. In any
event the user can disable this function at any time by cancelling the access
code.
9.2.9 - Remote use
All control panels can be called via the telephone, on the fixed line, by dialling
the relative number. The control panel HSCU1GC can also be called on the
GSM network, by dialling the number of the SIM card used.
The control panel HSCU1G, though equipped with the GSM module, cannot
receive calls as this module is normally switched off to reduce battery con-
sumption.
33
Advertisement
Table of Contents
