Advertisement
Available languages
Available languages
Package contents
The package contains:
1 Partly assembled table saw
1 Front support rail
1 Rear support rail
1 Box containing:
1 Bevel crank
1 Push block
1 Push stick
1 Saw blade
1 Mitre fence assembly
1 Mitre fence face
1 Throat plate insert
1 Riving knife and guard assembly
1 Fence head assembly
1 Combination wrench
1 Blade wrench
1 Torx wrench T50
1 Allen key 5 mm
4 Front rail brackets
1 Wrench hook
2 Hex head bolts M10 x 35
8 Hex head bolts M10 x 25
4 Coach bolts M8 x 20
4 Torx bolts T50, M10 x 30
8 Hex nuts M10
4 Hex nuts M8
4 Lock washers 8 mm
14 Lock washers 10 mm
14 Flat washers 10 mm
1 Box containing:
2 Support tables
1 Box containing:
1 Fence beam
1 Box containing:
1 Reversible fence face
1 Box containing:
1 Outfeed table
4 L-shaped brackets
2 Flat brackets
2 Coach bolts
2 Wing nuts
6 Hex head bolts M10 x 25
4 Hex head bolts M10 x 35
10 Hex nuts M10
10 Lock washers 10 mm
10 Flat washers 10 mm
1 Wiring diagram
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
Description (fig. A1 & A2)
Your D
WALT woodworker's table saw DW746/DW746T is a professional
E
machine designed for sawing wood, wood products and plastics.
Fig. A1
1 On/off-switch
2 Height adjuster
3 Bevel scale
4 Rip fence
21
5 Fence face
6 Throat plate insert
7 Riving knife
8 Blade guard
9 Power connector
10 Mitre fence
Fig. A2
11 Front rail
12 Rear rail
13 Saw blade
14 Bevel adjuster
15 Dust port 100 mm
16 Floor anchor hole
17 Outfeed table
18 Dust port 38 mm
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
2
conductor size is 1.5 mm
.
When using a cable reel, always unwind the cable completely. Also refer to
the table below.
Conductor size (mm
2
)
Cable rating (Amperes)
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
15
Voltage
Amperes
Cable rating (Amperes)
230
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
Three-phase machines should be wired directly into the mains by a
suitably qualified electrician.
Voltage drops
Inrush currents cause short-time voltage drops. Under unfavourable power
supply conditions, other equipment may be affected.
If the system impedance of the power supply is lower than 0.25 ø,
disturbances are unlikely to occur.
Assembly and adjustment
Prior to assembly and adjustment always unplug the tool.
Unpacking the saw and its parts
When moving the machine, always seek assistance.
The machine is too heavy for one person to handle.
• Remove the boxes attached to the main box.
• Cut the staples at the bottom of the main box and remove the carton
from the saw by pulling it up.
E N G L I S H
25
30
45
60
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
-
en - 3
Advertisement
