DeWalt DW743N User Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Saw
  5. DW743N
  6. User manual

DeWalt DW743N User Manual

Flip-over saw dw743n
Hide thumbs Also See for DW743N:
Table of Contents

Advertisement

Quick Links

DW743N
www.
.eu

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DW743N

Summary of Contents for DeWalt DW743N

  • Page 1 DW743N www.
  • Page 2 Copyright D WALT...
  • Page 3 10 11...
  • Page 4 30 31 33 32...
  • Page 7 62 63 60 61...
  • Page 8 3-8 mm...

  • Page 11: Technical Data

    E NG L I S H FLIP-OVER SAW DW743N The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 61029 Congratulations! and may be used to compare one tool with another. It may be used for You have chosen a D WALT tool.

  • Page 12: Safety Instructions

    EN G LI S H 13. Do not overreach. Keep proper footing and balance at all times. 14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing Horst Grossmann accessories.

  • Page 13: Additional Safety Rules For Mitre Saws

    ENGLISH – gloves for handling saw blades and rough material. Saw blades • Do not use cracked or damaged saw blades. should be carried in a holder wherever practicable. • Do not use any abrasive discs. • Refrain from removing any cut-offs or other parts of the work piece •...

  • Page 14: Additional Safety Rules For Table Saws

    ENG LI SH • Always keep the push stick in its place when not in use. Do not use the riving knife when using the machine in the mitre saw mode. Make sure that the riving knife is secured in •...

  • Page 15: Electrical Safety

    E NG L I S H 19 Foot Electrical Safety 20 Table locking device The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating 21 Saw table retention bracket plate.
  • Page 16 ENG LI SH Mounting the Machine to the Workbench (fi g. C2) • Place the blade spanner and Hex key in their storage position. WARNING: After mounting or replacing the blade, always With the legs removed, the machine is suitable for placement on a check that the blade is fully covered by the guard.

  • Page 17: Prior To Operation

    E NG L I S H WARNING: Always make a trial cut in a piece of waste WARNING: Never use your saw in bench saw mode wood, to check for accuracy. without the upper guard correctly fitted. Adjusting the Fence (fi g. J1, J2) Mounting and Adjusting the Parallel Fence (fi...

  • Page 18: Compound Mitre

    EN G LI S H • Ensure the material to be sawn is firmly secured in place. WARNING: Do not allow the sawhead to jump back unaided to prevent damage. • Apply only a gentle pressure to the tool and do not exert side pressure on the saw blade.

  • Page 19: Optional Attachments

    ENGLISH • Set the blade height and angle. • Connect one hose to the small diameter outlet and one to the large diameter outlet using the corresponding spouts. • Insert the slide bar (83) of the mitre fence into the groove (84) provided in the left-hand side of the table (fig.

  • Page 20: Optional Accessories

    EN G LI S H GUARANTEE • Slightly oil the rotating table bearing surface where it slides on the lip of the fixed table at regular intervals. • Clean the parts subject to accumulation of sawdust and chips WALT is confident of the quality of its products and offers periodically with a dry brush.
  • Page 24 Türkiye KALE Hırdavat ve Makina A.Ş. Tel: 0212 533 52 55 Defterdar Mah. Savaklar Cad. No:15 Faks: 0212 533 10 05 Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE www.dewalt.com.tr United Kingdom WALT Tel: 01753-56 70 55 210 Bath Road Fax:...

Table of Contents