Ftg Mode Via Ebl (Local Configuration) - LG 32LG710H Owner's Manual

FTG Mode via EBL (Local Configuration)

The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV
connection. Refer to the Free-To-Guest (FTG) Configuration Application manual for further information.
Notes: • FTG Device Configuration Application software is available online at: www.LGcommercial.com/
FTGsoftware.
• If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the
FTG Channel Map and FTG Installer Menu settings. Instead, refer to and use the processes
described on pages 35 to 37 to reconfigure the TV CPU.
• If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, refer
to Reference section, "Resetting Factory Defaults on the TV(s)," for further information before
proceeding.
1. Install (if necessary) and launch the FTG Device
Configuration Application (v5.0.0 or higher) on the
PC that will be used to configure the EBL.
2. Build an FTG Channel Map using the FTG Channel
Map Editor in the FTG Channel Map Configuration
Utility (or, if applicable, open an existing FTG
Configuration [.rml] file).
Note: Up to 141 logical channels can be defined in
the FTG Channel Map.
3. Connect the PC to the TV-LINK CFG jack on the
TV's rear connections panel using a USB-to-TTL
serial cable (TTL-232R-5V-AJ). If necessary, install
the device driver on the PC.
4. Turn ON the TV.
Note: If Installer Menu item 118 POWER SAVINGS
is set to 3 (default), the TV must be ON in order for
steps 5 and 6 below to be successful.
5. "Write" the FTG Channel Map to the EBL (switches
the EBL from Pass-through Mode to FTG Mode).
Note: After a "Write" of new data, the TV will briefly
display a green text banner that shows the EBL firm-
ware version and release date.
6. "Read" the current FTG Installer Menu settings from
the EBL using the FTG Installer Menu Configuration
Utility. If necessary to make changes to Installer
Menu items, "Write" them back to the EBL in FTG
Mode.
7. Save the FTG Channel Map and FTG Installer Menu
settings to an FTG Configuration (.rml) file for future
use.
8. Tune the TV to a Logical Channel in the FTG
Channel Map.
40
LD660H/LD665H
Jack Panel
LAN2
RESET
HDMI/DVI IN
..........
2
TV-LINK CFG
LAN2
RESET
HDMI/DVI IN
..........
1
..........
2
TV-LINK CFG
..........
1
.....
.....
.....
AUDIO IN
RJP RGB IN (PC)
INTERFACE (RGB/DVI)
.....
.....
.....
AUDIO IN
RJP RGB IN (PC)
INTERFACE (RGB/DVI)
USB-to-TTL Serial Cable
Required for direct PC-to-TV
FTG configuration.
LV555H
Jack Panel
RESET
LAN1
UPDATE
HDMI/DVI IN
RESET
LAN1
TV-LINK CFG
..........
1
LAN2
UPDATE
HDMI/DVI IN
TV-LINK CFG
..........
1
LAN2
RJP
.....
.....
.....
AUDIO IN
INTERFACE RGB IN (PC)
(RGB/DVI)
RJP
.....
.....
.....
AUDIO IN
RGB IN (PC)
INTERFACE
(RGB/DVI)
USB-to-TTL Serial Cable
Required for direct PC-to-TV
FTG configuration.
TV-LINK CFG
Use for direct PC-to-
TV FTG configuration.
Laptop
PC
Laptop
PC
TV-LINK CFG
Use for direct PC-to-
TV FTG configuration.
Laptop
PC
Laptop
PC
206-4200