Advertisement
QQ
3 7 63 1515 0
PANEL VIEW-3
REAR PANEL
1
2
VIDEO OUTPUT
COMPONENT 2
Y
P
P
B
COMPONENT 1
Y
P
P
B
R
AUDIO OUTPUT
ANALOG
L
R
5
COMPONENT 1 VIDEO OUTPUT
1
These RCA/phono connectors can be used to connect a
TV or projector with RCA/phono component video
inputs.
The DPC-7.5 has two component video outputs, the
TE
L 13942296513
COMPONENT 1 and COMPONENT 2, however, they
output the same video signal.
COMPONENT 2 VIDEO OUTPUT
2
These BNC connectors can be used to connect a TV or
projector with BNC component video inputs.
The DPC-7.5 has two component video outputs, the
COMPONENT 1 and COMPONENT 2, however, they
output the same video signal.
S VIDEO OUTPUT
3
These connectors can be used to connect TVs or projec-
tors with S-Video inputs.
The DPC-7.5 has two S-Video output connectors. They
output the same video signal.
VIDEO OUTPUT
4
These RCA/phono connectors can be used to connect
TVs or projectors with composite video inputs.
The DPC-7.5 has two composite video output connec-
tors. They output the same video signal respectively.
ANALOG AUDIO OUTPUT
5
These RCA/phono connectors can be connected to the
analog audio inputs on your TV, hi-fi amp, AV receiver,
or surround sound decoder (Dolby Pro Logic). There are
two sets of outputs. You could connect one set to your AV
www
receiver, the other to your TV for those occasions when
you want to watch a DVD-Video but don't want to use
your AVreceiver.
The DPC-7.5 has two pairs of stereo analog audio output
.
connectors. They output the same audio signal respec-
tively.
http://www.xiaoyu163.com
3
4
R
AUDIO OUTPUT
RS 232
DIGITAL
S VIDEO
OPTICAL
COAXIAL
VIDEO
IN
IR
OUT
REMOTE
CONTROL
6
7
8
9
10
x
ao
y
i
http://www.xiaoyu163.com
8
DVD CHANGER
DPC-7.5
MODEL NO.
IR IN/OUT
6
The IR IN connector can be used to connect a commer-
cially available IR receiver, which can be used to pickup
signals from the remote controller when the DPC-7.5 is
located in another room, installed in a rack, or is out of
range of the remote controller
Q Q
3
6 7
1 3
The IR OUT connector can be used to connect a com-
mercially available IR emitter, which can be used to pass
remote controller signals received by the IR IN along to
other AV components.
REMOTE CONTROL
7
These
nected to the
Onkyo AV components for interactive control.
To use
connection between your DPC-7.5 and Integra/Onkyo
AV receiver, even if they are connected digitally
OPTICAL AUDIO OUTPUT
8
This optical digital audio output can be connected to an
optical digital audio input on a hi-fi amp, AV receiver, or
surround sound decoder (Dolby Digital, DTS).
COAXIAL AUDIO OUTPUT
9
This coaxial digital audio output can be connected to an
coaxial digital audio input on a hi-fi amp, AV receiver, or
surround sound decoder (Dolby Digital, DTS).
RS 232
10
This RS-232 port can be connected to an external con-
troller.
AC INLET
11
The supplied power cord is connected here. The other
u163
end of the power cord should be connected to a suitable
wall outlet.
.
2 9
9 4
2 8
AC INLET
11
1 5
0 5
8
2 9
9 4
(Remote Interactive) connectors can be con-
connectors on your other Integra/
you must also make an analog RCA/phono
m
co
DPC-7.5
9 9
2 8
9 9
Advertisement
