Download
Share
Print this page
Senco SFT10XP Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Senco Manuals
  4. Power Tool
  5. SFT10XP
  6. Operating instructions manual

Senco SFT10XP Operating Instructions Manual

Fine wire stapler
Hide thumbs Also See for SFT10XP:

Advertisement

Quick Links

Download this manual See also: Operating Instructions Manual
SFT10XP
Fine Wire Stapler
Operating Instructions

Advertisement

loading

Related Manuals for Senco SFT10XP

Summary of Contents for Senco SFT10XP

  • Page 1 SFT10XP Fine Wire Stapler Operating Instructions...

  • Page 2: Table Of Contents

    tablE oF CoNtENtS Employer’s Responsibilities ....... 2 Safety Warnings ........3 Tool Use ............ 7 Maintenance ..........9 Troubleshooting ........10 Accessories ..........10 Technical Specifications ......11 Fastener Specifications ......11 Limited Warranty ........12 EmployER’S RESpoNSibilitiES Employer must enforce compliance with the safety warnings and all other instructions which accompany this tool as shipped from the...

  • Page 3: Safety Warnings

    SaFEty WaRNiNgS Warning! Read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Save these instructions Use safety equipment. Always wear ANSI Z87.1 safety glasses with permanently attached side shields. Dust mask, non-skid safety shoes, hard hat, or hear- ing protection must be used for appropriate conditions.
  • Page 4 SaFEty WaRNiNgS Drive fasteners into work surface only; never into materials too hard to penetrate. Do not drive fasteners on top of other fasteners or with the tool at too steep of an angle; the fasteners can ricochet and hurt someone.
  • Page 5 Never use a tool that leaks air or needs repair. Use only parts, fasteners, and accessories recommended or sold by SENCO. Do not modify tool without authorization from SENCO. Use only clean, dry, regulated compressed air at recommended pressure.
  • Page 6 (5) NEVER point tool at yourself or others in work area. (6) NEVER use oxygen or other bottled gases. Explosion may occur. (7) MAX AIR PRESS. 120 PSI (8.3 BAR) Always place yourself in a firmly balanced position when using or handling the tool. For information on the “SENCO Safety First Program,” contact your SENCO representative.

  • Page 7: Tool Use

    Push latch. ② Slide rail open. Connect air supply and lay strip of staples into magazine. Use only genuine SENCO fas- teners (see Parts Chart). Do not load with trigger de- pressed. Push rail forward until it latches. to drive fasteners: ①...
  • Page 8 ② Slide rail open. Remove staples. Remove jammed fastener. Connect air supply and lay strip of staples into magazine. Use only genuine SENCO fas- teners (see Parts Chart). Do not load with trigger depressed. Push rail forward until it latches.

  • Page 9: Maintenance

    Do not use tool if trigger sticks or binds. Squirt Senco pneumatic oil (5 to 10 drops) into the air inlet daily (depending on frequency of tool use). Other oils may damage O-rings and other tool parts.

  • Page 10: Troubleshooting

    Parts Kits SFt10Xp / Dl / lN auto / auto-Dl Ⓐ YK0802 Ⓑ YK0803 YK0804 Symptom Air leak near top of tool / Sluggish operation Solution Verify air supply / Tighten screws or install Firing Ⓐ System Kit Symptom Air leak near bottom of tool / Poor return.

  • Page 11: Technical Specifications

    tECHNiCal SpECiFiCatioNS FaStENER SpECiFiCatioNS Minimum to maximum operating pressure 65–100 psi 4,5–7 bar Air Consumption (60 cycles per minute) 1.16 scfm 33 liter 6S0001N, 6S0101N 6S0011N, 6S0211N, 6S0311N Air Inlet 1/4 in. NPT 1/4 in. NPT .030" Maximum Speed (cycles per second) 30 (Automatic) 30 (Automatic) 3/16"...